Husqvarna GTH2548 Owner's Manual page 13

Hide thumbs Also See for GTH2548:
Table of Contents

Advertisement

The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor
or per form ing any adjustments or repairs. We rec om mend a wide vi sion safety mask over spec-
tacles or stan dard safe ty glasses.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 8)
Your tractor is equipped with an operator presence sens-
ing switch. When engine is running, any attempt by the
op er a tor to leave the seat without fi rst setting the parking
brake will shut off the engine.
Depress brake pedal into full "BRAKE" position and
hold.
Place parking brake lever in "ENGAGED" position
and re lease pressure from brake pedal. Pedal should
re main in "BRAKE" position. Make sure parking brake
will hold tractor secure.
CHOKE
CON TROL
THROTTLE
CONTROL
LEVER
BRAKE PEDAL
"BRAKE"
POSITION
"DRIVE"
HEIGHT
PO SI TION
AD JUST MENT
KNOB
STOPPING (See Fig. 8)
MOWER BLADES -
To stop mower blades,move attachment clutch switch
to "DIS EN GAGED" po si tion.
GROUND DRIVE -
To stop ground drive, depress brake pedal into full
"BRAKE" position.
IMPORTANT: THE MOTION CONTROL LEVER RETURNS TO
NEUTRAL (N) POSITION WHEN THE BRAKE PEDAL IS FULLY
DEPRESSED.
ENGINE -
Move throttle control between half and full speed (fast)
position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stop ping may cause engine
to "backfi re".
Turn ignition key to "OFF" position and remove key.
Always remove key when leaving tractor to prevent
un author ized use.
Never use choke to stop engine.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY
TO BE DIS CHARGED, (DEAD).
OPERATION
AT TACH MENT CLUTCH SWITCH
PULL OUT TO "ENGAGE"
PUSH IN TO
"DISENGAGE"
IGNITION
KEY
MOTION
CONTROL LEVER
"DISENGAGED"
PO SI TION
PARKING BRAKE
"EN GAGED" PO SI TION
FIG. 8
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot en gine exhaust gases may
cause "browning" of grass. To eliminate this possibility, al-
ways stop engine when stopping tractor on grass areas.
CAUTION: Always stop tractor com-
plete ly, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
TO USE THROTTLE CONTROL (See Fig. 8)
Always operate engine at full throttle.
Operating engine at less than full throttle reduces
the battery charging rate.
Full throttle of fers the best mower performance.
TO USE CHOKE CONTROL (See Fig. 8)
Use choke control whenever you are starting a cold engine.
Do not use to start a warm engine.
To engage choke control, pull knob out. Slowly push
knob in to disengage.
TO MOVE FORWARD AND BACKWARD
(See Fig. 8)
CAUTION: Do not attempt to operate motion control
lever when the parking brake is set or when the
brake pedal is depressed. Doing so may result in
misadjustment to the drive con trol sys tem.
The direction and speed of movement is controlled by the
motion control lever.
Start tractor with motion control lever in neutral (N)
position.
Release parking brake.
Slowly move motion control lever to desired position.
TO ADJUST MOWER CUTTING HEIGHT
(See Fig. 8)
The cutting height is controlled by turning the height ad-
just ment knob in desired direction.
Turn knob clockwise (
Turn knob counterclockwise (
height.
The cutting height range is approximately 1-1/2" to 4-1/2".
The heights are measured from the ground to the blade tip
with the engine not running. These heights are ap proxi mate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the fi rst cut
relatively high; the second to desired height.
13
) to raise cutting height.
) to lower cutting

Advertisement

Table of Contents
loading

Table of Contents