Portable Model WSLP1100 . . . 13–15 Washer Connections for Stationary Models WSLS1100 and WSLM1100 ... . . 11–12 Troubleshooting Tips Before You Call For Service . . 16–19 Status Indicators ....16 Consumer Support Consumer Support .
PROPER INSTALLATION This washer must be properly installed and located in accordance with the Installation Instructions before it is used. Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
5 years. Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside. READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY. SAVE THESE INSTRUCTIONS www.GEAppliances.com...
Page 4
Special washer features. Before starting the washer: • Load the laundry in the washer. Add the detergent and fabric softener to the dispenser drawer. • • Add bleach (if needed) to the bleach dispenser. Detergent and Fabric Softener Dispenser Drawer...
SPIN ONLY WASH LOAD OPTIONS Before starting the washer: • Load the laundry in the washer. • Add the detergent and fabric softener to the dispenser drawer. • Add bleach (if needed) to the bleach dispenser. To Use Automatic One-Touch Washing...
Page 6
LOAD SIZE The water level should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer basket. WASH CYCLE These wash cycles control the length of the washing process. The chart below will help match the WASH CYCLE setting to your specific laundry needs.
Page 7
Loading the Washer Load dry items loosely, no higher than the top row of holes in the washer tub. When loading wet items make sure you set the load/water level high enough to allow the items to move freely. Water level should just cover the clothes.
Loading and using the washer. Fabric Care Labels Below are fabric care label “symbols” that affect the clothing you will be laundering. WASH LABELS Machine wash cycle Water temperature DRY LABELS Tumble Heat setting High Special instructions BLEACH LABELS Bleach...
15 or 20 amp circuit breaker or time- delay fuse. If the washer is plugged into the dryer’s 115 volt outlet, then the dryer needs to be on a dedicated circuit. TOOLS REQUIRED Pliers ⁄...
CAUTION: Before plugging in washer, read the following electrical requirements. ELECTRICAL REQUIREMENTS CAUTION: For personal safety, do not use an extension cord or adapter plug with this appliance. Do not, under any circumstances, cut or remove the third grounding prong from the power cord. Follow National Electrical Codes or prevailing local codes and ordinances.
WASHER CONNECTIONS FOR STATIONARY MODELS WSLS1100 AND WSLM1100 WARNING: Make sure the washer is unplugged. FLUSH WATER LINES Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog up the water valve screens.
WASHER CONNECTIONS FOR STATIONARY MODELS WSLS1100 AND WSLM1100 (CONT.) PLUG THE POWER CORD INTO A GROUNDED OUTLET Insure proper ground exists before use RUN THE WASHER THROUGH A COMPLETE CYCLE Check for water leaks and proper operation. ALCOVE OR CLOSET INSTALLATION...
WASHER CONNECTIONS FOR PORTABLE MODEL WSLP1100 – ONE-FAUCET CONNECTIONS Use the hose connector provided with the washer for a one-faucet connection. TO CONNECT THE WASHER: REMOVE THE UNI-COUPLE HOSE FROM INSIDE THE WASHER BASKET Drain Connection Faucet Connector COLD Water...
WASHER CONNECTIONS FOR PORTABLE MODEL WSLP1100 – ONE-FAUCET CONNECTIONS (CONT.) MAKE SURE THE TEMPERATURE SELECTOR IS SET AT COLD/COLD SLOWLY TURN ON THE WATER FAUCET ALL THE WAY TO THE DESIRED TEMPERATURE SETTING PLUG THE POWER CORD INTO A 3-PRONG GROUNDED OUTLET The electrical power cord is on the back of the washer.
WASHER CONNECTIONS FOR PORTABLE MODEL WSLP1100 – TWO-FAUCET CONNECTIONS If you have two separate water connections, your washer can be connected to both the hot and cold water faucets. This kit can be purchased from your dealer or from Parts and Accessories.
Make sure the drain hose is not kinked and is connected properly. Wash load is unbalanced. Distribute laundry evenly in the basket. Make sure washer is level. See Leveling the Washer . Washer lid is not closed. Close lid. Any time the total time required is more than 99 minutes,...
Page 17
• Make sure house water heater is delivering water at 120°F.–140°F.(48°C.–60°C.). • Straighten drain hose and make sure washer is not sitting on it. • Top of drain outlet should be less than 8 ft. above floor.
Page 18
• Make sure load size selector matches clothes load size. • Check fabric softener package for instructions and follow directions for using dispenser. • While this is not caused by the washer, you can slow the pilling process by washing garments inside out.
Page 19
• Press the START/PAUSE button to stop the washer, open the lid and redistribute the load evenly. Close the lid and restart. • Pull washer away from the wall; about 4 is needed. • This is normal. WHAT TO DO •...
Page 21
You can rest easy, knowing that all your valuable household products are protected against expensive repairs. Place your confidence in GE and call us in the U.S. toll-free at for more information. *All brands covered, up to 20 years old, in the continental U.S.
After mailing the registration below, store this document in a safe place. It contains information you will need should you require service. Our service number is 800 GE CARES (800-432-2737). Model Number Model Number Last Name E-mail Address State Phone...
Page 23
Any part of the washer which fails due to a defect in materials or workmanship. During this One Year full one-year warranty, GE will also provide, free of charge, all labor and in-home service to replace From the date of the the defective part.
Caution must be exercised, since improper servicing may cause unsafe operation. Contact Us If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations Register Your Appliance Register your new appliance on-line—at your convenience! Timely product registration will allow for...