GE JV536 Owner's Manual And Installation Instructions page 13

12 MARK HOLES
Select the vent option that your installation will
require and proceed to that section:
A.Outside top exhaust
(Vertical duct—3
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
" (30" hood)
13 15 ⁄
16
" (36" hood)
16 15 ⁄
16
Cabinet front
Cabinet Bottom
"
5 1 ⁄
4
Vertical duct
5"
access hole
"
1 1 ⁄
4
Wood shims
(recessed-
Center
bottom cabinets only)
B.Outside top exhaust (Vertical duct—7
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
" (30" hood)
13 15 ⁄
16
" (36" hood)
16 15 ⁄
16
Cabinet front
Cabinet
bottom
Access
"
hole for 7
round duct
Wood shims
(recessed-
Center
bottom cabinets only)
C.Outside rear exhaust
(Horizontal duct—3
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Wood shims
(recessed-bottom cabinets only)
Cabinet front
" Horizontal duct
3 ⁄
3
4
access hole
Cabinet
5
bottom
" (30" hood)
13 15 ⁄
16
" (36" hood)
16 15 ⁄
16
Hood mounting screws (4)
Installation Instructions
" "
1 ⁄ x 10 Rectangular)
4
" (30" hood)
13 15 ⁄
16
" (36" hood)
16 ⁄
15
16
"
7 1 ⁄
2
"
5 1 ⁄
4
2"
1 1 ⁄
Electrical access hole
(in cabinet bottom)
line
"
Round)
" (30" hood)
13 15 ⁄
16
" (36" hood)
16 ⁄
15
16
"
7 1 ⁄
2
"
8 DIA.
2"
HOLE
5"
1 1 ⁄
2
Electrical access
hole
(in cabinet bottom)
line
" "
1 ⁄ x 10 Rectangular)
4
" "
1 ⁄ 3 ⁄
8 4
"
"
5 1 ⁄
1 ⁄
4 4
"
7 1 ⁄
2
" (30" hood)
13 ⁄
15
16
" (36" hood)
16 15 ⁄
16
Electrical access hole
Center line
(in wall)
D.Recirculating (non-vented ductless—
Available on JV5 Series models only)
• Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
• Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
13 FOR RECESSED-BOTTOM
CABINETS ONLY
"
10 ⁄
1
2
"
2
• If the cabinets have front, side or back trim, make
2 wood shims the width of the trim and attach them
to the cabinet bottom recess on both sides. See Step
12 for marking locations.
14 CUT HOLES
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4" extra
toward the front of the cabinet so you can move the
duct freely when installing the hood. It may also ease
installation by cutting the hole 10
"
10 1 ⁄
2
"
15 RUN WIRES
Run the electrical wires through the wall or
cabinet according to National Electrical Code
and applicable local codes.
NOTE: DO NOT turn the power on until
installation is complete.
16 SCREW IN PARTWAY
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the
keyhole slots marked on the cabinet bottom.
FEED IN WIRES
17
Lift the hood into position and feed the house
wiring through the wiring knockout.
13
Wood shims
" instead of 10".
1 ⁄
2