Lennox Hearth Products LADERA BK Installation And Operation Instructions Manual
Lennox Hearth Products LADERA BK Installation And Operation Instructions Manual

Lennox Hearth Products LADERA BK Installation And Operation Instructions Manual

Epa wood-burning fireplace

Advertisement

SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
A French manual is available upon request. Order P/N 506023-04.
Ce manuel d'installation est disponible en francais, simplement en faire
la demande. Numéro de la pièce 506023-04.
surfaces of this appliance will be hot
during operation and will retain heat
for a while after shutting off the appli-
ance. Severe burns may result.
Carefully supervise children in the
same room as appliance.
If small children are present in the home, it is
recommended that this appliance be fitted with
an adjustable safety gate or barrier screen.
WARNING
Listed to standards:
ULC-S610 and UL-127
Report # 3151759
PILADERA REV. 4 05/2013
INSTALLATION AND

OPERATION INSTRUCTIONS

Ladera™
EPA Wood-Burning Fireplace
P/N 506023-03 REV. D 05/2013
MODELS
Ladera-BK
This installation manual will enable you to obtain a safe, efficient and
dependable installation of your fireplace system. Please read and
understand these instructions before beginning your installation.
Do not alter or modify the fireplace or its components under any circum-
stances. Any modification or alteration of the fireplace system, including
but not limited to the fireplace, chimney components and accessories,
may void the warranty, listings and approvals of this system and could
result in an unsafe and potentially dangerous installation.
IHP wood-burning fireplaces are designed for use as a supplemental
heater. They are not intended for continuous use as a primary heat
source.
The fireplace cannot be operated without a door
or firescreen. Consult your dealer to select the
correct replacement door or firescreen.
cal connection must be made prior to fireplace
installation
plumb condition, using shims as necessary at
sides and/or bottom.
instructions.
WARNING
-

Advertisement

Table of Contents
loading

Summary of Contents for Lennox Hearth Products LADERA BK

  • Page 1: Operation Instructions

    INSTALLATION AND OPERATION INSTRUCTIONS Ladera™ EPA Wood-Burning Fireplace P/N 506023-03 REV. D 05/2013 MODELS Ladera-BK This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system. Please read and understand these instructions before beginning your installation. Do not alter or modify the fireplace or its components under any circum- stances.
  • Page 2: Safety Rules

    WARNING WARNING PRECAUTIONS. READ AND Be careful adding wood fuel to the Use care when selecting window treatments for windows located fire or handling fireplace tools such near the fireplace. Avoid using as shovels, tongs or pokers. combustible flowing window WARNING treatments such as curtains on WARNING...
  • Page 3: Table Of Contents

    OPTIONAL EQUIPMENT Order Separately - See Pages 21 through 24 When you purchased your new fireplace, you joined the ranks of thousands of individuals whose answer to their home heating needs reflects their concern for aesthetics, efficiency and our environment. We extend our continued support to help you achieve the maximum - AC Chimney Starter Section AC Chimney benefit and enjoyment available from your new fireplace.
  • Page 4: Starting And Maintaining A Fire

    First Fires The main source of air (primary air) entering For instance, a long chimney will necessitate the firebox can be diminished by moving the closing the damper more. To obtain the proper Before using the fireplace make sure to remove air combustion control from left to right.
  • Page 5: Important Cautions

    A. Negative pressure in the house 5. Check outside to ensure that sparks and hot As the fire burns, air goes up the chimney. embers coming out of the chimney are not This air must be replaced through leakage igniting the roof. Creosote - Formation and Need for Removal into the house or through the outside air duct 6.
  • Page 6: Disposing Of Ashes

    DISPOSING OF ASHES Remove ashes only when the fire is out and the ashes are cold (24 to 48 hours after the fire is out). Do not leave the ashes in the house as they give off carbon monoxide and other toxic gases. WARNING Disposal of Ashes: Ashes should 1.
  • Page 7: Glass Care - Replacement

    GLASS CARE Gasket Replacement If possible, you should choose a location where Remove the door from the unit (see Page 6) the chimney will pass through the house without Glass Replacement cutting floor or roof joists (see fireplace dimen- and lay it on a clean unabrasive surface. To The glass used for the Ladera™...
  • Page 8: Optional Cast Facade Installation

    Optional Cast Facade installation WARNING: THE HEARTH EXTEN- Install the Facade per instructions provided in Fireplace Facade Kit (ordered separately - see Page 21). AS ILLUSTRATED. Framing, Facing And Mantel The crack between the fireplace The construction of the framing, facing, and and the hearth extension must be Safety Metal Strip sealed with a non-combustible...
  • Page 9: Framing Dimensions

    Back Wall of Chase/Enclosure OUTSIDE CHASE Including Finishing Materials, if any Corner Installation FRAMING DIMENSIONS 20-5/8” 35-7/8 911 mm 37-5/8” 956 mm * Zero Clearance 29-1/8” 740 mm From Back Spacer to Wall 12-1/2” 318 mm 70” 1778 mm 35” 889 mm Rough Framing Face (Unfinished Shown) 18-5/8”...
  • Page 10: Nailing Flanges

    Insulate Joists Same As Ceiling Insulated Chase Construction Storm Collar Roof Support Flashing Draft Stops Attic Radiation Shield NOTE: It is recommend- Floor ed that the chase walls Ceiling Firestop and floor be insulated in Wall the same manner, using the same insulation, as CTDT Termination...
  • Page 11: Fireplace Blower

    Once the repair is done, it is mandatory to apply a new high temperature black cement Only non-combustible mate- Frame rial should be superposed or projecting over the front of sealing the access plate and all screw holes. Grill the fireplace. Because the Ladera™...
  • Page 12: Central Forced Air Kit

    Central Forced Air Kit Rain Cap NOTE: Not tested under EPA certification. If installed, this appliance no longer qualifies for EPA certification. Flashing Collar Flashing The knock-outs provided on the back and on the sides of the Ladera™ fireplace allow the Roof Support connection of insulated flexible pipe which Attic Radiation Shield...
  • Page 13: Outside Air Kit

    Adaptor Insulated Flex Pipe Figure 17 Insulation Blower Flex 5” Diameter Tightening Collar Aluminum Tape Figure 18 OUTSIDE AIR KIT The outside air kit is optional on the Ladera™ fireplace, but mandatory on the AC chimney. It can be burned drawing air only from the house. When the fireplace is in operation with the door closed, it will pull only a slight amount of air from the house.
  • Page 14: Chimney System

    Outside Air Installation The outside air assembly may be installed according to the following Chimney Installation Notes requirements: 1. If possible, install an interior chimney as it will provide better perfor- A) Duct length should be kept to a minimum. The maximum length of a mance.
  • Page 15: Chimney Installation Instructions

    Attic Radiation Shield INSTRUCTIONS Attic Radiation ASHT / S2100 Air Cooled Pipe * Shield HT6103+ / HT6000+ 1. Cut and frame the holes in the ceiling, floor Solid Packed Pipe * and roof where the chimney will pass (see Figure 23). center of the holes.
  • Page 16: Offset Chimney Installation

    elbow, proceed as follows: Air Cooled Chimney * Chimney ASHT+ / HT6103+ / S-2100+ / HT6000+ Collar Chimneys Spacer (built 1. Install the first elbow; turn it in the required direction. Fasten it to the chimney with provided with the elbow. 2.
  • Page 17 Offset Dimensions Total Height Horizontal Offset Chimney Elbow Offset & One Length Between Elbows Two Lengths Between Elbows Height 6” 8” 12” 18” 24” 36” 48” 8” & 48” 12” & 48” 18” & 48” 24” & 48” 36” & 48” 48”...
  • Page 18: Angled Wall Radiation Shield

    ANGLED WALL RADIATION SHIELD When traversing a combustible wall with the chimney at a 30º or 45º Chimney AC angle, an angled firestop or wall radiation shield must be installed. Only one is required. RSMI45 NOTE: 45º angle for Canada only ( In cold climate locations (climates where temperatures will fall below 32°...
  • Page 19: Chimney Support Installation

    Universal Roof Support When installing a support, slightly lift the chimney system so the weight will lie on the support, not on the fireplace to reduce expansion noises. This support has three possible uses: roof to support the chimney 2. It may be used on a floor, ceiling or roof above an offset to support the chimney above the offset.
  • Page 20: Masonry Application Instructions

    Follow these steps: 1. Position the fireplace in its location. Temporarily install the ASHT+ WARNING: Before starting the installation, the masonry chimney must elbow on the top of the fireplace and, using a level, mark with an oval the location where the flue liner will enter the masonry chimney. 2.
  • Page 21: Installation Accessories

    OPTIONAL INSTALLATION ACCESSORIES Central Forced Air Kit Accessories Central Forced Air Kit, Central forced air kit including: Installation Accessories BISFWK-1 pipe adapter (BISAVF), back draft damper (BISBD), aluminium Description Cat./ Part No. tape, BISFWK-1 Flexible pipe 5” I.D. x 15 ft. Long, 5FLEX15 5FLEX15 Outside Air Kit Flexible pipe 5”...
  • Page 22: Replacement Parts

    REPLACEMENT PARTS LIST SPECIFICATIONS Ladera™ Replacement Parts Cat. No. Model Description H7162 Ladera-BK Ladera EPA Wood-Burning Fireplace Description Part/Cat. No. Andiron (2 pieces) PR-SR2897 Bottom refractory PR-SR2825 Product Reference Information Back refractory PR-SR2826 Weight 215 lbs Left side refractory PR-SR2828 Height Right side refractory PR-SR2827...
  • Page 23: Chimney Components Lists

    The components listed below must be ordered from Security Chimneys International™. Contact your Security Chimneys Distributor or Dealer for ordering information. Security Chimneys International Limited 450-973-9999 2125 Monterey, Laval, Quebec Canada, H7L 3T6 www.securitychimneys.com Secure Temp ASHT 1” High Temp. Insulated Stainless Steel Chimney ®...
  • Page 24 The components listed below must be ordered from Security Chimneys International™. Contact your Security Chimneys Distributor or Dealer for ordering information. Security Chimneys International Limited 450-973-9999 2125 Monterey, Laval, Quebec Canada, H7L 3T6 www.securitychimneys.com Tubinox™ LL Chimney Lining System Gravity Kit Accessories Rigid Stainless Steel Liner For Relining A Masonry Chimney, 6”...
  • Page 25 NOTES...
  • Page 26: Product Reference Information

    Normally, all parts should be ordered through your IHP distributor or dealer. Parts will be shipped at prevailing prices at time of order. Your fireplace is covered by a limited warranty. Please read the warranty When ordering repair parts, always give the following information: to be familiar with its coverage.

This manual is also suitable for:

Ladera-bk

Table of Contents