Sign in today to find solutions:

Don't have an account? Sign up

Hewlett-Packard ProLiant DL360p Maintenance And Service Manual

Hp proliant dl360p gen8 server.

 
HP ProLiant DL360p Gen8 Server
Maintenance and Service Guide
Abstract
This guide describes identification and maintenance procedures, diagnostic tools, specifications, and requirements for hardware components and
software. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in
recognizing hazards in products, and are familiar with weight and stability precautions.
Part Number: 664727-004a
September 2013
Edition: 4a
Next page ->

Summary of Contents

  • Page 1

    HP ProLiant DL360p Gen8 Server Maintenance and Service Guide Abstract This guide describes identification and maintenance procedures, diagnostic tools, specifications, and requirements for hardware components and software. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in recognizing hazards in products, and are familiar with weight and stability precautions.

  • Page 2

    © Copyright 2012, 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    Contents Customer self repair ........................5 Parts only warranty service ..........................5 Illustrated parts catalog ....................... 15 Mechanical components ..........................15 System components ............................ 18 Removal and replacement procedures ................... 25 Required tools ............................25 Preparation procedures ..........................25 Power down the server ........................25 Extend the server from the rack ......................

  • Page 4: Table Of Contents

    Hard drive backplane cabling ........................67 FBWC capacitor pack cabling........................68 DVD-ROM and DVD-RW drive cabling ......................69 Chipset SATA cable option ......................... 69 Diagnostic tools .......................... 73 Troubleshooting resources ........................... 73 HP Insight Diagnostics ..........................73 HP Insight Diagnostics survey functionality ..................74 HP ROM-Based Setup Utility ........................

  • Page 5: Customer Self Repair, Parts Only Warranty Service

    Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement.

  • Page 6

    Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés. Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation.

  • Page 7

    In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica di un addetto del centro di supporto tecnico HP.

  • Page 8

    defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den Kurier-/Frachtdienst. Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner vor Ort.

  • Page 9

    enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local.

  • Page 10

    Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma van HP. Informatie over Service Partners vindt u op de HP website (http://www.hp.com/go/selfrepair). Garantieservice "Parts Only" Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de bepalingen van de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter beschikking stellen.

  • Page 11

    No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço. Customer self repair 11...

  • Page 12

    Customer self repair 12...

  • Page 13

    Customer self repair 13...

  • Page 14

    Customer self repair 14...

  • Page 15: Illustrated Parts Catalog, Mechanical Components

    Illustrated parts catalog Mechanical components Item Description Spare part Customer self number repair (on page 5) Access panel — — a) Caged heatsink access panel 671351-001 Mandatory b) Screw-down heatsink access panel* 743499-001 Mandatory Miscellaneous hardware kit 671354-001 Mandatory a) Power supply blank —...

  • Page 16

    Item Description Spare part Customer self number repair (on page 5) a) 8 SFF hard drive cage* ** 667868-001 Mandatory b) 10 SFF hard drive cage** 692479-001 Mandatory c) 4 LFF hard drive cage* ** 667869-001 Mandatory Rack mounting hardware —...

  • Page 17

    Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen. No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt.

  • Page 18: System Components

    System components Illustrated parts catalog 18...

  • Page 19

    Item Description Spare part Customer self number repair (on page 5) Hot-plug power supplies — — a) 460 W, 92% 511777-001 Mandatory b) 460 W, Platinum Plus, 94%* 660184-001 Mandatory c) 500 W, 277 V AC, 94%* 638549-001 Mandatory d) 750 W, 277 V AC, 94%* 674890-001 Mandatory e) 750 W, Titanium 96%*...

  • Page 20

    Item Description Spare part Customer self number repair (on page 5) m) 2.50-GHz Intel Xeon processor E5-2640, 95W* ** † 670527-001 Optional n) 2.0-GHz Intel Xeon processor E5-2640v2, 95W* ** † 730239-001 Optional o) 3.30-GHz Intel Xeon processor E5-2643, 130W* ** † 670538-001 Optional p) 3.3-GHz Intel Xeon processor E5-2643v2, 130W* ** †...

  • Page 21

    Item Description Spare part Customer self number repair (on page 5) n) 8-GB, PC3-14900R-13, dual-rank x4* 715273-001 Mandatory o) 8-GB, PC3-14900R-13, quad-rank x4* 735303-001 Mandatory p) 8-GB, PC3L-12800R-11, quad-rank x4* 735302-001 Mandatory q) 8-GB, PC3-12800R-1, single-rank x4* 664691-001 Mandatory r) 8-GB, PC3L-10600R-9, dual-rank x4* 664690-001 Mandatory s) 8-GB, PC3L-10600E-9, dual-rank x8*...

  • Page 22

    Item Description Spare part Customer self number repair (on page 5) j) 400-GB, SATA, MLC SSD, 6.35 cm (2.5 in)* 653967-001 Mandatory k) 400-GB, SATA, MLC SSD, 8.89 cm (3.5 in)* 653970-001 Mandatory l) 400-GB, SAS, MLC SSD, 6.35 cm (2.5 in)* 653963-001 Mandatory m) 400-GB, SAS, SLC SSD, 6.35 cm (2.5 in)*...

  • Page 23

    Item Description Spare part Customer self number repair (on page 5) Hard drive data cable or Mini-SAS cable, 45 cm (18 in)* 667874-001 Mandatory Hard drive data cable or Mini-SAS cable, 64 cm (25 in)* 667875-001 Mandatory Power to hard drive backplane cable* 667873-001 Mandatory Front video adapter*...

  • Page 24

    Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía correspondiente al producto.

  • Page 25: Removal And Replacement Procedures, Required Tools, Preparation Procedures, Power Down The Server

    Removal and replacement procedures Required tools You need the following items for some procedures: • T-10/T-15 Torx screwdriver • HP Insight Diagnostics software ("HP Insight Diagnostics" on page 73) Preparation procedures To access some components and perform certain service procedures, you must perform one or more of the following procedures: •...

  • Page 26: Extend The Server From The Rack, Access The Hp Systems Insight Display

    This method forces the server to enter standby mode without properly exiting applications and the OS. If an application stops responding, you can use this method to force a shutdown. • Use a virtual power button selection through HP iLO. This method initiates a controlled remote shutdown of applications and the OS before the server enters standby mode.

  • Page 27

    8 SFF configuration The display can be rotated up to 90 degrees. Removal and replacement procedures 27...

  • Page 28: Safety Considerations, Preventing Electrostatic Discharge

    10 SFF configuration The display can be rotated up to 90 degrees. Safety considerations Before performing service procedures, review all the safety information. Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts.

  • Page 29: Symbols On Equipment, Server Warnings And Cautions

    • Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. • Place parts on a grounded surface before removing them from their containers. • Avoid touching pins, leads, or circuitry. • Always be properly grounded when touching a static-sensitive component or assembly. Symbols on equipment The following symbols may be placed on equipment to indicate the presence of potentially hazardous conditions.

  • Page 30: Access Panel, Drive Blank

    WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all •...

  • Page 31: Hot-plug Drive

    Remove the drive blank. To replace the component, slide the component into the bay until it clicks. Hot-plug drive CAUTION: For proper cooling, do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open.

  • Page 32: Power Supply Blank, Ac Power Supply

    Power supply blank Remove the blank. To replace the component, reverse the removal procedure. AC power supply CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. To remove the component: Power down the server (on page 25).

  • Page 33: V Dc Power Supply Option

    To replace the component, reverse the removal procedure. 48V DC power supply option One of the following optional HP input cables with pre-fastened ring tongues may be purchased from HP or an authorized reseller: • A5S97A—1.3-m (7.55-ft) 48V DC Power Cable Kit •...

  • Page 34

    Remove the safety cover. Remove the power ring tongues from the terminal block. Removal and replacement procedures 34...

  • Page 35

    Remove the ground (earthed) wire from the ground screw and washer. Attach the screws to the terminal block. IMPORTANT: The minimum nominal thread diameter of a pillar or stud type terminal must be 3.5 mm (0.138 in); the diameter of a screw type terminal must be 4.0 mm (0.157 in). Removal and replacement procedures 35...

  • Page 36

    Remove the power supply from the power supply bay. If you are not immediately replacing the power supply, install the safety cover. To replace the component: If you are not using an optional HP input cable or the ring tongues you crimped previously, with the ground cable disconnected from the 48V power source, crimp the ring tongues to the power and ground cables coming from the 48V source.

  • Page 37

    Remove the safety cover from the terminal block on the front of the power supply. Remove the screws from the terminal block. IMPORTANT: The minimum nominal thread diameter of a pillar or stud type terminal must be 3.5 mm (0.138 in); the diameter of a screw type terminal must be 4.0 mm (0.157 in). Removal and replacement procedures 37...

  • Page 38

    Attach the ground (earthed) wire to the ground screw and washer and tighten to 1.47 N m (13 lb-in) of torque. The ground wire must be connected before the positive or negative lead wires. Attach the power ring tongues to the terminal block, following the polarity label below the terminal block, and then tighten the screws to 1.47 N m (13 lb-in) of torque.

  • Page 39

    Replace the safety cover. Insert the power supply into the power supply bay until it clicks into place. Route the power cord. Use best practices when routing power cords and other cables. A cable management arm is available to help with routing. To obtain a cable management arm, contact an HP authorized reseller.

  • Page 40: Drive Cage Assembly, Dvd-rom Or Dvd-rw Drive

    Drive cage assembly The hard drive cage assembly includes the Systems Insight Display ("Systems Insight Display LEDs" on page 84), front panel LEDs and buttons (on page 78), drive backplane, and cables. To remove the component: Power down the server (on page 25). Remove all power: Disconnect each power cord from the power source.

  • Page 41

    Remove the access panel ("Access panel" on page 30). If installed, remove the FBWC capacitor pack ("FBWC capacitor pack" on page 45). For SFF drives, do the following: Disconnect the SATA DVD cable from the system board to fully remove the DVD drive from the bay ("DVD-ROM and DVD-RW drive cabling"...

  • Page 42: Fan Module

    Disconnect the SATA DVD cable from the rear of the DVD drive ("DVD-ROM and DVD-RW drive cabling" on page 69). To replace the component, reverse the removal procedure. Fan module The server has eight fans. Install fans 1 and 2 only when processor 2 is installed. When only one processor is installed, install the fan blanks in bays 1 and 2 ("Fan modules"...

  • Page 43: Fan Blank

    The illustration shows fans 1 and 2 removed for a single-processor configuration. To replace the component: Install the fan module. Install the access panel ("Access panel" on page 30). Slide the server into the rack. Power up the server. Fan blank Install fans 1 and 2 only when processor 2 is installed.

  • Page 44: Flash-backed Write Cache Procedures, Cache Module

    Remove all power: Disconnect each power cord from the power source. Disconnect each power cord from the server. Extend the server from the rack (on page 26). Remove the access panel ("Access panel" on page 30). Remove the fan blanks. To replace the component, reverse the removal procedure.

  • Page 45: Fbwc Capacitor Pack

    Extend the server from the rack (on page 26). Remove the access panel ("Access panel" on page 30). If installed, remove the FBWC capacitor pack ("FBWC capacitor pack" on page 45). Remove the PCI riser cage ("PCI riser cage" on page 50). Remove the cache module.

  • Page 46: Recovering Data From The Flash-backed Write Cache

    The server may look different than the one shown in the following illustration, depending on the server model. To replace the component, reverse the removal procedure. Recovering data from the flash-backed write cache If the server fails, use the following procedure to recover data temporarily stored in the FBWC. CAUTION: Before starting this procedure, read the information about protecting against electrostatic discharge...

  • Page 47: Front Video Adapter, Flexiblelom

    Front video adapter Depending on the model purchased, the server may look different than shown. The 10 SFF drive configuration does not support the front video adapter. Remove the component as indicated. CAUTION: Be sure to connect the video adapter to the video connector, and not to the USB connector.

  • Page 48

    Remove the existing FlexibleLOM. To replace the component: Firmly seat the FlexibleLOM in the slot, and then tighten the thumbscrew. Install the access panel ("Access panel" on page 30). Slide the server into the rack. Connect the LAN segment cables. Connect each power cord to the server.

  • Page 49: Rack Bezel, Air Baffle

    Rack bezel Remove the component as indicated. To replace the component, reverse the removal procedure. Air baffle To remove the component: Power down the server (on page 25). Remove all power: Disconnect each power cord from the power source. Disconnect each power cord from the server. Extend the server from the rack (on page 26).

  • Page 50: Pci Riser Cage

    The server may look different than the one shown in the following illustration, depending on the server model. To replace the component, reverse the removal procedure. PCI riser cage To remove the component: CAUTION: To prevent damage to the server or expansion boards, power down the server and remove all AC power cords before removing or installing the PCI riser cage.

  • Page 51: Expansion Boards

    The server may look different than the one shown in the following illustration, depending on the server model. To replace the component, reverse the removal procedure. Expansion boards To remove the component: Power down the server (on page 25). Remove all power: Disconnect each power cord from the power source.

  • Page 52: Pcie Riser Board, Dimms

    PCIe riser board To remove the component: Power down the server (on page 25). Remove all power: Disconnect each power cord from the power source. Disconnect each power cord from the server. Extend the server from the rack (on page 26). Remove the access panel ("Access panel"...

  • Page 53: Heatsink

    Remove the DIMM. To replace the component, reverse the removal procedure. Heatsink WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: The heatsink thermal interface media is not reusable and must be replaced if the heatsink is removed from the processor after it has been installed.

  • Page 54

    Caged heatsink Screw-down heatsink Removal and replacement procedures 54...

  • Page 55

    To replace the component: Remove the thermal interface protective cover from the heatsink. Install the heatsink, ensuring the alignment bracket aligns on the front of the heatsink. Caged heatsink Removal and replacement procedures 55...

  • Page 56: Processor

    Screw-down heatsink Install the access panel ("Access panel" on page 30). Slide the server into the rack. Connect each power cord to the server. Connect each power cord to the power source. Power up the server. Processor WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them.

  • Page 57

    Disconnect each power cord from the power source. Disconnect each power cord from the server. Extend the server from the rack (on page 26). Remove the access panel ("Access panel" on page 30). Remove the heatsink ("Heatsink" on page 53). Open each of the processor locking levers in the order indicated, and then open the processor retaining bracket.

  • Page 58

    To replace the component: Install the processor. Verify that the processor is fully seated in the processor retaining bracket by visually inspecting the processor installation guides on either side of the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED.

  • Page 59

    Press and hold the processor retaining bracket in place, and then close each processor locking lever. Press only in the area indicated on the processor retaining bracket. Remove the thermal interface protective cover from the heatsink. Install the heatsink, ensuring the alignment bracket aligns on the front of the heatsink: Removal and replacement procedures 59...

  • Page 60

    Caged heatsink Screw-down heatsink Install the access panel ("Access panel" on page 30). Slide the server into the rack. Connect each power cord to the server. Connect each power cord to the power source. Removal and replacement procedures 60...

  • Page 61: System Battery

    Power up the server. System battery If the server no longer automatically displays the correct date and time, you may need to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack.

  • Page 62: System Board

    To remove the component: IMPORTANT: Be sure you are using the correct spare part. The HP ProLiant DL360p Gen8 Server ships with one of two different system boards that each use specific processors and heatsinks. To identify the proper system board spare part number, see the white label on the system board that shipped with the server.

  • Page 63

    The server may look different than the one shown in the following illustration, depending on the server model. To replace the component: Align the system board on the tray, and tighten the thumbscrew to secure it. The server may look different than the one shown in the following illustration, depending on the server model.

  • Page 64

    Open each of the processor locking levers in the order indicated, and then open the processor retaining bracket. Install the processor. Verify that the processor is fully seated in the processor retaining bracket by visually inspecting the processor installation guides on either side of the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED.

  • Page 65

    Close the processor retaining bracket. When the processor is installed properly inside the processor retaining bracket, the processor retaining bracket clears the flange on the front of the socket. CAUTION: Do not press down on the processor. Pressing down on the processor may cause damage to the processor socket and the system board.

  • Page 66: Hp Trusted Platform Module

    Install the access panel ("Access panel" on page 30). Slide the server into the rack. Connect each power cord to the server. Connect each power cord to the power source. Power up the server. IMPORTANT: Install all components with the same configuration that was used on the failed system board.

  • Page 67: Cabling, Cabling Overview, Hard Drive Backplane Cabling

    Cabling Cabling overview This section provides guidelines that help you make informed decisions about cabling the server and hardware options to optimize performance. For information on cabling peripheral components, refer to the white paper on high-density deployment at the HP website (http://www.hp.com/products/servers/platforms). CAUTION: When routing cables, always be sure that the cables are not in a position where they can be pinched or crimped.

  • Page 68: Fbwc Capacitor Pack Cabling

    • FBWC capacitor pack cabling The second (left) capacitor pack cable connects to an optional Smart Array expansion board. Cabling 68...

  • Page 69: Dvd-rom And Dvd-rw Drive Cabling, Chipset Sata Cable Option

    DVD-ROM and DVD-RW drive cabling The server may look different than the one shown in the following illustration, depending on the server model. Chipset SATA cable option With the chipset SATA cable option, the chipset SATA controller can be used with a single SATA hard drive that is installed in one hard drive bay of the SFF or LFF hard drive cage.

  • Page 70

    To install the component: Power down the server (on page 25). Remove all power: Disconnect each power cord from the power source. Disconnect each power cord from the server. Extend the server from the rack (on page 26). Remove the access panel ("Access panel"...

  • Page 71

    Disconnect the SATA cable from the optical drive and the SATA connector on the system board. The optical bay is disabled with the chipset SATA cable option. Connect the chipset SATA cable: Connect the chipset SATA cable connector to the chipset SATA controller port on the system board. The chipset SATA connector on the SATA cable is narrower than the chipset SATA controller port header on the system board.

  • Page 72

    Clip the cable to the power supply air baffle when routing it along the edge of the system board. Coil the cables behind the hard drive backplane to minimize airflow impact. Install the access panel ("Access panel" on page 30). Install the server into the rack.

  • Page 73: Diagnostic Tools, Troubleshooting Resources, Hp Insight Diagnostics

    Diagnostic tools Troubleshooting resources The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, issue resolution, and software maintenance on ProLiant servers and server blades. To view the guide, select a language: •...

  • Page 74: Hp Insight Diagnostics Survey Functionality, Hp Rom-based Setup Utility, Integrated Management Log

    HP Insight Diagnostics survey functionality HP Insight Diagnostics (on page 73) provides survey functionality that gathers critical hardware and software information on ProLiant servers. This functionality supports operating systems that are supported by the server. For operating systems supported by the server, see the HP website (http://www.hp.com/go/supportos). If a significant change occurs between data-gathering intervals, the survey function marks the previous information and overwrites the survey data files to reflect the latest changes in the configuration.

  • Page 75: Usb Support And Functionality, Usb Support, Internal Usb Functionality

    USB support and functionality USB support HP provides both standard USB 2.0 support and legacy USB 2.0 support. Standard support is provided by the OS through the appropriate USB device drivers. Before the OS loads, HP provides support for USB devices through legacy USB support, which is enabled by default in the system ROM.

  • Page 76: Component Identification, Front Panel Components

    Component identification Front panel components • 8 SFF Item Description SAS/SATA/SSD drive bay 1 SAS/SATA/SSD drive bay 2 SAS/SATA/SSD drive bay 3 SAS/SATA/SSD drive bay 4 SAS/SATA/SSD drive bay 5 SAS/SATA/SSD drive bay 6 SAS/SATA/SSD drive bay 7 Systems Insight Display DVD-ROM drive (optional) SAS/SATA/SSD drive bay 8 Front video connector (front video port adapter required)

  • Page 77

    • 4 LFF Item Description SAS/SATA/SSD drive bay 1 DVD-ROM drive (optional) SAS/SATA/SSD drive bay 2 Serial number tab SAS/SATA/SSD drive bay 3 Systems Insight Display SAS/SATA/SSD drive bay 4 Front video connector (front video port adapter required) USB connectors (2) •...

  • Page 78: Front Panel Leds And Buttons

    Item Description Systems Insight Display USB connector Front panel LEDs and buttons • 8 SFF or 4 LFF Item Description Status UID button/LED Solid blue = Activated Flashing blue (1 Hz/cycle per sec) = Remote management or firmware upgrade in progress Off = Deactivated Power On/Standby button Solid green = System on...

  • Page 79: Rear Panel Components

    • 10 SFF Item Description Status UID button/LED Solid blue = Activated Flashing blue (1 Hz/cycle per sec) = Remote management or firmware upgrade in progress Off = Deactivated Power On/Standby button Solid green = System on and system power LED Flashing green (1 Hz/cycle per sec) = Performing power on sequence Solid amber = System in standby Off = No power present*...

  • Page 80: Rear Panel Leds And Buttons

    Item Description Slot 2 PCIe 3.0 x16 (full height/half length) FlexibleLOM ports (Shown: 4x1Gb / Optional: 2x10Gb) Video connector Serial connector Slot 1 PCIe 3.0 x8 (low profile) iLO management port USB connectors (4) Power supply bay 2 Power supply bay 1 Rear panel LEDs and buttons Item Description...

  • Page 81: System Board Components

    Item Description Status • AC power unavailable • Power supply failed • Power supply in standby mode • Power supply exceeded current limit Power supply 1 LED Solid green = Normal Off = One or more of the following conditions exists: •...

  • Page 82: Dimm Slots

    Item Description SAS connector B (Drives 5–8) SAS connector A (drives 1–4) NMI jumper System maintenance switch Processor 1 Fan module 8 connector Processor 1 DIMM slots Fan module 7 connector Fan module 6 connector Fan module 5 connector Processor 1 DIMM slots Fan module 4 connector Processor 2 DIMM slots Fan module 3 connector...

  • Page 83: System Maintenance Switch, Nmi Jumper

    System maintenance switch Position Default Function Off = HP iLO security is enabled. On = HP iLO security is disabled. Off = System configuration can be changed. On = System configuration is locked. Reserved Reserved Off = Power-on password is enabled. On = Power-on password is disabled.

  • Page 84: Systems Insight Display Leds

    Systems Insight Display LEDs The HP Systems Insight Display LEDs represent the system board layout. The display provides status for all internal LEDs and enables diagnosis with the access panel installed. To view the LEDs, access the HP Systems Insight Display (on page 26). Description Status Off = Normal...

  • Page 85: Systems Insight Display Led Combinations

    Systems Insight Display LED combinations When the health LED on the front panel illuminates either amber or red, the server is experiencing a health event. Combinations of illuminated Systems Insight Display LEDs, the system power LED, and the health LED indicate system status.

  • Page 86: Device Numbers

    Device numbers • 4 LFF configuration • 8 SFF configuration • 10 SFF configuration IMPORTANT: A cache module is required for a 10 SFF drive cage. Drives installed in a 10 SFF configuration do not function without a cache module. For more information, see the server user guide.

  • Page 87: Hot-plug Drive Led Definitions, Fan Modules

    Hot-plug drive LED definitions Item Status Definition Locate Solid blue The drive is being identified by a host application. Flashing blue The drive carrier firmware is being updated or requires an update. Activity ring Rotating green Drive activity No drive activity Do not remove Solid white Do not remove the drive.

  • Page 88

    When only one processor is installed, be sure the fan blanks are always installed in bays 1 and 2 to ensure proper cooling. • Two-processor configuration Install fans 1 and 2 only when processor 2 is installed. When only one processor is installed, always install the fan blanks.

  • Page 89: Storage And Expansion Diagram

    Storage and expansion diagram Component identification 89...

  • Page 90: Specifications, Environmental Specifications, Server Specifications, Power Supply Specifications

    Specifications Environmental specifications Specification Value — Temperature range* 10°C to 35°C (50°F to 95°F) Operating -30°C to 60°C (-22°F to 140°F) Non-operating — Relative humidity (noncondensing) 10% to 90% Operating 28°C (82.4°F), maximum wet bulb temperature 5% to 95% Non-operating 38.7°C (101.7°F), maximum wet bulb temperature * All temperature ratings shown are for sea level.

  • Page 91: Hp 460w Common Slot Gold Hot Plug Power Supply (92% Efficiency)

    • HP 750W Common Slot Gold Hot Plug Power Supply (92% efficiency) (on page 93) • HP 750W Common Slot Platinum Plus Hot Plug Power Supply (94% efficiency) (on page 94) • HP 750W Common Slot -48VDC Hot Plug Power Supply (94% efficiency) (on page 94) •...

  • Page 92: Hp 500w Common Slot 277vac Hot Plug Power Supply (94% Efficiency)

    460 W at 100V to 120V AC input Rated steady-state power 460 W at 200V to 240V AC input 460 W at 100V to 120V AC input Maximum peak power 460 W at 200V to 240V AC input HP 500W Common Slot 277VAC Hot Plug Power Supply (94% efficiency) Specification Value...

  • Page 93: Hp 750w Common Slot Titanium Hot Plug Power Supply (96% Efficiency)

    HP 750W Common Slot Titanium Hot Plug Power Supply (96% efficiency) Specification Value Input requirements — 200 to 240 V AC Rated input voltage 50 Hz to 60 Hz Rated input frequency 4.1 A at 200 V AC Rated input current 3.3 A at 240 V AC 820 W at 200 V AC Maximum rated input power...

  • Page 94: Hp 750w Common Slot Platinum Plus Hot Plug Power Supply (94% Efficiency)

    HP 750W Common Slot Platinum Plus Hot Plug Power Supply (94% efficiency) Specification Value Input requirements 100 to 120 VAC, 200 to Rated input voltage 240 VAC 50 Hz to 60 Hz Rated input frequency 8.5 A at 100 VAC Rated input current 4.1 A at 200 VAC 843 W at 100V AC input...

  • Page 95: Hp 1200w Common Slot Platinum Plus Hot Plug Power Supply (94% Efficiency)

    If this connection is made, all of the following must be met: This equipment must be connected directly to the DC supply system earthing electrode • conductor or to a bonding jumper from an earthing terminal bar or bus to which the DC supply system earthing electrode conductor is connected.

  • Page 96: Hot-plug Power Supply Calculations

    Hot-plug power supply calculations For hot-plug power supply specifications and calculators to determine electrical and heat loading for the server, see the HP Power Advisor website (http://www.hp.com/go/hppoweradvisor). Specifications 96...

  • Page 97: Acronyms And Abbreviations

    Acronyms and abbreviations double data rate Desktop Management Interface FBWC flash-backed write cache Integrated Lights-Out Integrated Management Log large form factor LAN on Motherboard nonmaskable interrupt NVRAM nonvolatile memory PCIe Peripheral Component Interconnect Express POST Power-On Self Test QuickPath Interconnect Acronyms and abbreviations 97...

  • Page 98

    RBSU ROM-Based Setup Utility serial attached SCSI SATA serial ATA Secure Digital small form factor Trusted Platform Module unit identification universal serial bus Acronyms and abbreviations 98...

  • Page 99: Documentation Feedback

    Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback. Documentation feedback 99...

  • Page 100: Index

    Index AC power supply 32, 91, 92, 93, 94, 95 electrostatic discharge 28 access panel 30 environmental specifications 90 air baffle 15, 25, 49 expansion boards 51 extending server from rack 26 battery 61 buttons 25, 76, 78, 80 fan blank 43 fan LED 84 fan module location 87 fan modules, installation 42...

  • Page 101

    IML (Integrated Management Log) 74 processors 56 Insight Diagnostics 73, 74 Integrated Management Log (IML) 74 internal cables 67 rack bezel 49 internal USB functionality 75 rack, extending server from 26 RBSU (ROM-Based Setup Utility) 74 rear panel buttons 80 LED, power on 78 rear panel components 79 LED, system power 78...

  • Page 102

    UID button 80 UID LED 80 USB (universal serial bus) 75 USB connector 76, 79 USB support 75 utilities 73 utilities, deployment 74 video connector 76, 79 warnings 29 Index 102...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: