Vivotek FE8172V Quick Installation Manual

Fixed dome network camera, 5mp, 360 surround view, poe, ip66, vandal-proof
Hide thumbs Also See for FE8172V:

Advertisement

Quick Links

FE8172V
Quick Installation Guide
繁中
簡中
日本語
English
Indonesia
Dansk
5MP • 360˚ Surround View • PoE • IP66 • Vandal-proof
Fixed Dome
Network Camera
Français
Español
Deutsch
Türkçe
Português
Italiano
Русский
Česky
Svenska
Polski
Nederlands

Advertisement

Table of Contents
loading

Summary of Contents for Vivotek FE8172V

  • Page 1 FE8172V Fixed Dome Network Camera Quick Installation Guide Русский Česky Svenska 繁中 簡中 日本語 Nederlands Türkçe English Français Español Deutsch Português Italiano Polski Indonesia Dansk 5MP • 360˚ Surround View • PoE • IP66 • Vandal-proof...
  • Page 2: Package Contents

    Do not insert sharp or tiny objects Do not drop the Network Camera. into the Network Camera. Package Contents FE8172V Mounting Plate / Screwdriver Alignment Stickers Screws / Dessicant Bag / Double-sided Tape / Rubber Seal...
  • Page 3: Physical Description

    Physical Description Inner View Contacts for Internal Microphone (B) Lens Spring Contacts (A) Align (B) to (A) when attaching the dome cover Header (J6) Ethernet 10/100 RJ45 Socket Header (J7) Status LEDs Reset Button MicroSD/SDHC/SDXC Card Slot EN - 2...
  • Page 4: Built-In Microphone

    Outer View IP66-rated Vandal-proof Dome Cover Built-in Microphone IMPORTANT: Record the MAC address under the 083236 camera base before installing the camera. Hardware Installation First, use the supplied screwdriver to loosen the four screws and detach the dome cover from the camera base.
  • Page 5: Connecting Dc Power Cable

    Connecting RJ45 Ethernet Cable RJ45 Cable Dimension (unit: mm) Recommended cable gauge: 24AWG (0.51 mm) Assembly Steps Rubber Seal Plug 1. Drill a hole on the rubber seal plug and in- sert an Ethernet cable through the opening. 2. Strip part of the sheath from the Ethernet cable.
  • Page 6 Ceiling/Wall Mount without Mounting Plate (Choose this mounting type if you want to feed the cables form the bottom of the camera) 1. Attach the supplied alignment sticker for camera base to the ceiling/wall. 2. Using the three circles on the sticker, drill three pilot holes into the ceiling. Then hammer the three supplied plastic anchors into the holes.
  • Page 7 Ceiling/Wall Mount with Mounting Plate (Choose this mounting type if you would like to feed the cables form the side) 1. Attach the supplied alignment sticker for the supplied mounting plate to the ceiling/wall. 2. Using the three circles on the sticker, drill three holes into the ceiling. Then hammer the three supplied plastic anchors into the holes.
  • Page 8: Network Deployment

    You may also use the diagonal holes on the mounting plate, marked as A, B, or C, to install the camera to a standard 4 in. junction box. Network Deployment General Connection (without PoE) 1. Connect RJ45 Ethernet cable to a switch. 2.
  • Page 9 Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ether- net cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable.
  • Page 10: Assigning An Ip Address

    2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program. 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN.
  • Page 11 P/N:625018200G Rev.: 1.0 All specifications are subject to change without notice. Copyright 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. VIVOTEK USA, INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. 2050 Ringwood Avenue, San Jose, CA 95131 |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com...

Table of Contents