Download
Share
Print this page
Honeywell 5 Nm Series Product Data
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Controller
  5. 5 Nm Series
  6. Product data
Honeywell 5 Nm Series Product Data

Honeywell 5 Nm Series Product Data

Non-spring return direct-coupled damper actuators for floating and two-position control
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
5 Nm, 10 Nm Series
NON-SPRING RETURN DIRECT-COUPLED
DAMPER ACTUATORS FOR FLOATING AND
TWO-POSITION CONTROL
GENERAL
This non-spring return direct-coupled damper actuator
provides floating and two-position control for:
• air dampers,
• VAV units,
• air handlers,
• ventilation flaps,
• louvers, and
• reliable control for air damper applications with up to
10 sq ft (0.9 sq m) / 44 lb-in. (5 Nm) and 20 sq ft (1.9 sq m)
/ 88 lb-in. (10 Nm) (seal-less damper blades; air friction-
dependent).
FEATURES
• Declutch for manual adjustment.
• Adjustable mechanical end limits.
• Removable access cover for direct wiring.
• Mountable in any orientation.
• Rotation direction and service/OFF switch.
• Available with cable on select models.

SPECIFICATIONS

Supply voltage:
MN6105/MN6110: 24 Vac/Vdc -15%/+20%, 50/60 Hz.
Nominal voltage:
MN6105/MN6110: 24 Vac/Vdc, 50/60 Hz.
All values stated herein after apply to operation under nominal
voltage conditions.
Power consumption:
MN6105/MN6110: 5 VA / 2 W.
Ambient limits:
Ambient operating limits: -5...+140° F (20...+60° C).
Ambient storage limits: -22...+176° F (-30...+80° C).
Relative humidity: 5...95%, non-condensing.
Safety:
Protection standard: IP54.
Protection class: II as per EN 60730-1.
Overvoltage category: II.
Lifetime:
Full strokes: 60000.
Repositions: 1.5 million.
General .............................................................................
Features ...........................................................................
Specifications ...................................................................
Ordering Information ........................................................
Installation ........................................................................
Wiring ...............................................................................
PRODUCT DATA
Contents
1
1
1
2
3
4
63-2632-03

Advertisement

loading

Related Manuals for Honeywell 5 Nm Series

Summary of Contents for Honeywell 5 Nm Series

  • Page 1: Specifications

    5 Nm, 10 Nm Series NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR FLOATING AND TWO-POSITION CONTROL PRODUCT DATA FEATURES • Declutch for manual adjustment. • Adjustable mechanical end limits. • Removable access cover for direct wiring. • Mountable in any orientation. •...

  • Page 2: Ordering Information

    If you have additional questions, need further information, or would like to comment on our products or services, please write or phone: 1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory). 2. Honeywell Customer Care...

  • Page 3: Mounting Instructions

    5 NM, 10 NM SERIES Limitation of Rotation Stroke • The floating/2-position run mode (“Dir” for CCW-closing dampers or “Rev” for CW-closing dampers). Two adjustable mechanical end limits are provided to limit the angle of rotation as desired (See Fig. 3). The mechanical end limits must be securely fastened in place.
  • Page 4 5 NM, 10 NM SERIES Mounting Position The access cover can be unscrewed and removed in order to gain access to the terminal block(s) and perform wiring. The actuators can be mounted in any position (IP54 is dependent upon orientation; see Fig. 8). Choose a mounting NOTE: If factory installed wires not included.
  • Page 5 5 NM, 10 NM SERIES Table 2. Signals at Terminals from MN6105/MN6110. Terminal Signal in Floating Signal in 2-Pos. Mode END SWITCHES (CLASS II-ONLY) Common ~/- Common ~/- 5° 85° 24 V ~/- 24 V ~/- (control signal) (control/power signal) 24 V ~/- 24 V ~/- (control signal)
  • Page 6 5 NM, 10 NM SERIES DIMENSIONS 1-5/8 (41) 3-11/32 (85) 5-9/32 (134) 4-1/4 (108) Service/Off 2-7/16 (62) 2-19/32 (66) 144 (3658) CABLE AND STRAIN RELIEF ON SELECT MODELS ONLY. M28937 Fig. 11. Dimensions in inches (mm). 63-2632—03...
  • Page 7 5 NM, 10 NM SERIES 63-2632—03...
  • Page 8 Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive ® U.S. Registered Trademark © 2010 Honeywell International Inc. Toronto, Ontario M1V 4Z9 EN0B-0544GE51 R0810 63-2632—03 M.S. Rev. 10-10 customer.honeywell.com Printed in U.S.A.

This manual is also suitable for:

Mn6105Mn6110