Advertisement

Quick Links

To obtain the best possible performance and to avoid damage to your boat, install your GHP 10V marine autopilot system according to the
following instructions. Read all installation instructions before proceeding with the installation. If you experience difficulty during the
installation, contact Garmin Product Support or seek the advice of a professional installer.
The GHP 10V is compatible with C3 or newer Volvo

Product Registration

Help us better support you by completing our online registration today! Connect to our Web site at http://my.garmin.com. Keep the original
sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to each component of your GHP 10V system in the spaces provided on
numbers are located on a sticker on each component.

Contact Garmin

Contact Garmin Product Support if you have any questions while installing or using your GHP 10V autopilot system. In the USA, go to
www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to
www.garmin.com/support
phone at +44 (0) 870.8501241.
Warnings
You are responsible for the safe and prudent operation of your vessel. The GHP 10V is a tool that will enhance your capability to
operate your boat. It does not relieve you from the responsibility of safely operating your boat. Avoid navigational hazards and never leave
the helm unattended.
Always be prepared to promptly regain manual control of your boat.
Learn to operate the GHP 10V on calm and hazard-free open water.
Use caution when operating the GHP 10V at high speeds near hazards in the water, such as docks, pilings, and other boats.
See the Important Safety and Product Information guide in the product box for product warnings and other important information.
Cautions
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
When drilling or cutting, always check the opposite side of the surface. Be aware of fuel tanks, electrical cables, and hydraulic hoses.
Do not connect the CCU interface connector on either the CCU cable or the Autopilot Gateway to a NMEA 2000
September 2009
GHP
10V Installation Instructions
EVC systems. Contact Volvo for information on updating older EVC systems.
®
Contact Support
and click
190-01082-02 Rev. B
for in-country support information, or contact Garmin (Europe) Ltd. by
page
2. The serial
network.
®
Printed in Taiwan

Advertisement

Table of Contents
loading

Summary of Contents for Garmin GHP 10V

  • Page 1: Product Registration

    • You are responsible for the safe and prudent operation of your vessel. The GHP 10V is a tool that will enhance your capability to operate your boat. It does not relieve you from the responsibility of safely operating your boat. Avoid navigational hazards and never leave the helm unattended.
  • Page 2: Main Components

    Serial number Cables and Connectors Use the included cables to connect the GHP 10V components to power, to each other, to an alarm (provided), and to optional devices such as a NMEA 2000- or NMEA 0183-compatible GPS device. CCU cable Use this cable to connect the CCU to the Autopilot Gateway.
  • Page 3 (Garmin replacement part number: 010-11074-00) Alarm Wire the included alarm to the CCU using the CCU cable. The alarm provides audible alerts from the GHP 10V. (Garmin replacement part number: 010-11056-00) NMEA 2000 Cables and Connectors The NMEA 2000 cables connect the CCU and the GHC 10 to the NMEA 2000 network. Use the NMEA 2000 power cable and two terminators to create a NMEA 2000 network on your boat if one does not exist.
  • Page 4 Preparation Before installing the GHP 10V autopilot system, it is important that you completely understand where all the components will be located on your boat. Temporarily place all the components where you plan to install them. Ensure that all cables can reach the necessary components before mounting any of the components.
  • Page 5 Ignition or in-line switch Red (+) 8- Vdc 1 A fuse Black (-) GHP 10V Autopilot Gateway Orange(+) White (+) Alarm buzzer Blue (-) Black (-) Yellow CCU signal wire (see page GHP 10V General Wiring Diagram GHP 10V Installation Instructions...
  • Page 6: Installation Procedures

    Installation Procedures After you have completely planned the GHP 10V installation on your boat, and have satisfied all the mounting and wiring considerations for your particular installation, you can begin mounting and connecting the components. Installing the Course Computer Unit (CCU) Install the CCU by mounting it to your boat, connecting it to the Autopilot Gateway and to a NMEA 2000 network, and wiring it to power, to the alarm buzzer, and to the yellow CCU signal wire on the GHC 10.
  • Page 7 If the red (+) and black (-) wires are not long enough, extend the appropriate wires with 22 AWG wire. 3. Solder and cover all bare-wire connections. Installing the Autopilot Gateway The Autopilot Gateway allows the GHP 10V Autopilot System to communicate with the Volvo EVC system and steer the boat. Mounting the Autopilot Gateway ➊...
  • Page 8 8. Securely tighten the four mounting screws through the GHC 10 into the drilled mounting holes. note: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainless anti- seize lubricant to the screws before installing them.
  • Page 9 2. Connect the yellow CCU signal wire from the GHC 10 power/data cable to the yellow wire on the CCU cable. If you install multiple GHC 10 units and want to turn the GHP 10V autopilot system on with any of the installed GHC 10 units, connect all of the yellow CCU signal wires from the GHC 10 units to the yellow wire on the CCU cable.
  • Page 10 The GHC 10 must also connect to the CCU with the yellow CCU signal wire in the GHC 10 power/data cable. • To add additional sensors to your NMEA 2000 network, follow the instructions included with the sensors. GHP 10V Installation Instructions...
  • Page 11 The GHC 10 is not powered by the NMEA 2000 network. It must be separately connected to the power source. • The GHC 10 must also connect to the CCU with the yellow CCU signal wire in the GHC 10 power/data cable. GHP 10V Installation Instructions...
  • Page 12 Connecting an Optional GPS Device to the GHP 10V Autopilot System To use an optional optional GPS device with the GHP 10V, either connect a NMEA 2000-compatible GPS device to the NMEA 2000 network, or connect a NMEA 0183-compatible GPS device directly to the GHC 10.
  • Page 13 GHP 10V, use the advanced configuration power-on procedure. note: The first time you power on the GHP 10V, you will be prompted to complete the Sea Trial Wizard. You do not need to power on the unit using this power-on procedure to run the wizard for the first time.
  • Page 14 When you manually adjust the acceleration limiter, make small adjustments. Test the change before entering any further adjustments. Power on the GHP 10V using the advanced configuration power-on procedure (page 13). 3. On the GHC 10, select Menu > Setup > Dealer Autopilot Configuration > Turn Fine Tuning Setup > Acceleration Limiter. GHP 10V Installation Instructions...
  • Page 15 Manually Running the Sea Trial Wizard The Sea Trial Wizard allows you to quickly define all of the important configuration settings on the GHP 10V. If, after running the wizard and manually adjusting the gains, you do not feel as though the GHP 10V is working correctly, you can run the wizard again at any time.
  • Page 16 Certain configuration settings are available when using the GHC 10 normally, such as enabling and disabling the Shadow Drive, adjusting the sensitivity of the Shadow Drive, and adjusting the Sea State Filtering setting. See the configuration section of the GHC 10 Quick Start Manual for more information. GHP 10V Installation Instructions...
  • Page 17: Specifications

    Case Material: Fully gasketed, high-impact plastic alloy, waterproof to IEC 529 IPX7 standards Power GMi 10 power input source: 8–32 Vdc Fuse: AGC/3AG - 1 A GMi 10 power usage: 2.5 W max nMea 2000 Power input: 9–16 Vdc nMea 2000 Len: 2 (100 mA) GHP 10V Installation Instructions...
  • Page 18: Nmea 2000 Pgn Information

    Navigation Data NMEA 0183 Information The GHC 10, when connected to an optional NMEA 0183-compatible GPS device, uses the following NMEA 0183 sentences: Receive—wpl, gga, grme, gsa, gsv, rmc, bod, bwc, dtm, gll, rmb, and xte. transmit—hdg. GHP 10V Installation Instructions...
  • Page 19 Detach this checklist from the installation instructions and use it to assist with the GHC 10 installation process. Read all installation instructions before installing the GHC 10. Contact Garmin Product Support if you have any questions during the installation process.
  • Page 20 All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Table of Contents