Download
Share
Print this page
Daewoo 14Q1 Service Manual
  1. Manuals
  2. Brands
  3. Daewoo Manuals
  4. CRT TV
  5. Super Vision 14Q1
  6. Service manual

Daewoo 14Q1 Service Manual

38 / 48 / 51 cm mono colour television chassis : cp-370
Hide thumbs Also See for 14Q1:

Advertisement

Quick Links

See also: Instruction Manual
Service Manual
38 / 48 / 51 Cm Mono Colour Television
DAEWOO ELECTRONICS CO., LTD.
CHASSIS : CP-370
MODEL : 14Q1/20Q1/21Q1
14Q2/20Q2/21Q2
14Q3/20Q3/21Q4
14T1/20T1/21T1
14T2/20T2/21T2
14T3/20T3
@@ PP

Advertisement

loading

Related Manuals for Daewoo 14Q1

Summary of Contents for Daewoo 14Q1

  • Page 1 Service Manual 38 / 48 / 51 Cm Mono Colour Television CHASSIS : CP-370 MODEL : 14Q1/20Q1/21Q1 14Q2/20Q2/21Q2 14Q3/20Q3/21Q4 14T1/20T1/21T1 14T2/20T2/21T2 14T3/20T3 @@ PP DAEWOO ELECTRONICS CO., LTD.

  • Page 2: Table Of Contents

    CONTENTS Specifications ........................ 1 Safety Instruction ......................2 Circuit block Diagram ....................3 Alignment Instructions ....................4 IC Description ........................ 7 Circuit Description ....................... 31 PCB Layouts PRINTED CIRCUIT BOARDS ..................38 SCHEMATIC DIAGRAM ..................... 39 Trouble Shooting Charis ..................... 40 Important IC Voltage Charts ....................

  • Page 3: Specifications

    Specifications Q : 1SPEAKER MODEL, T : 2SPEAKER MODEL VM : WITHOUT TXT. MODEL, TM : WITH TXT. MODEL TV Standard PAL/SECAM-B/G, D/K, I, H, NTSC-3.58/4.43 Mains Voltage 100~250V AC, 50/60Hz Power Consumption 14”Q = 69W, 14”T = 74W 20”Q = 79W, 20”T = 84W 21”Q = 79W, 21”T = 84W Sound output .

  • Page 4: Safety Instruction

    Safety Instruction WARNING: Before servicing this chassis, read the “X-RAY RADIATION precaution”, “safety precaution” and “product safety notice” below. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially voltage should be checked. It is recommended hazardous X-RAY RADIATION.To avoid such the reading of the high voltage recorded as a part hazards, the high voltage must not exceed the of the service records.

  • Page 5: Alignment Instructions

    Alignment Instructions 1. AFT 1.1 Standard B/G,D/K,I 1) Set a Signal Generator with - RF FREQUENCY = 38.9 MHz, - RF OUTPUT LEVEL = 80 5 dBuV - System = PAL / SECAM - B/G, D/K, I NTSC - 3.58/4.43 2) Connect the Signal Generator RF Output to P101 (Tuner IF Output).
  • Page 6 6. GEOMETRY 6.1 VERTICAL CENTER 1) Set the TV to NOR I mode. 2) Pressing the V-SIZE UP/DOWN KEY, the lower half of the screen is blanked. 3) Adjust the border line of blanked picture coincident with the mechanical center marks of the CRT using the V-CENTER UP/DOWN KEY.
  • Page 7 If EEPROM(1703) has been changed ; - Option data has to be changed and - all alignment function has to be readjusted. The initial state of adjustment are as follows; - V-Center, V-Slope V-Size, H-Center, R, G, B, AFT = Center (30/64 - 33/64) - S-Correction = 00/64 - AGC = 15~60/64 Service Remocon...

  • Page 8: Ic Description

    IC Description DW370ASM* (Micro-controller for Non-Teletext Model) =TMS370C08A05 ( TI Type No.) (1) General Description The TMS370C08A05 devices are members of the cMCU370 family single-chip microcontrollers. The cMCU370 family provides cost effective real-time system control through use of the PRISM methodology. The PRISM methodology modular fabrication process integrates analog, digital, linear and power technologies on a single chip, thereby maximizing the total integration strategy.
  • Page 9 • 09 CMOS Compatible I/O Pins - All Peripheral Function Pins Software Configurable for Digital I/O - 6 Bidirectionals, 3 Input Pins • Plastic 42 YSDP Pins Package (3) Block Diagram...
  • Page 10 DW5255M*(Micro-controller & West/East Teletext Decoder) DW5255RM*(Micro-controller & Cyrillic Teletext Decoder) =SDA5255-A*** (SIEMENS Type No.) (1) General Description The TDA5255 contains a slicer for VPS and TTX, an accelerating acquisition hardware module, a display generator for “LEVEL 1” TTX data and a 8 bit u-controller running at 333 nsec cycle time. The controller with dedicated hardware guarantees flexibility, does most of the internal processing of TTX acquisition , transfers data to/from the external memory interface and receives/transmits data via I2C and UART user interfaces.
  • Page 11 • Controller: - 8 bit configuration - 18 MHz internal clock - 0.33 us instruction cycle - eight 16-bit data pointer registers (DPTR) - two 16-bit timers - watchdog timer - serial interface (UART) - 256 bytes on-chip RAM - 1 Kbyte on-chip extended RAM (access via MOVX) - 8 Kbyte on-chip ACQ-buffer-RAM (access via MOVX) - 6 channel 8-bit pulse width modulation unit - 2 channel 14-bit pulse width modulation unit...
  • Page 12 (4) Pin Description * A : DW5255M*/DW5255RM*, *B : DW370ASM* Name Description Symbol B* A* P3.1 T1IC1/CR NTSC OUT for switching SAW filter K6259 - PAL/SECAM : L - NTSC : H P0.7/Open Drain BUSSTOP I2C BUS STOP IN for Computer controlled alignment in Factory ( Active Low ) P0.6/Open Drain...
  • Page 13 Name Description Symbol B* A* CVBS CVBS CVBS IN P2.3/8 bit ADC Not Used 22 P2.2/8 bit ADC B0/AN0/ADC IF AGC INPUT for Auto Tuning System 23 P2.1/8 bit ADC B1/AN1/ADC Local KEY SCAN IN 24 P2.0/8 bit ADC B2/AN2/ADC S/SW Not Used 25 VSS...
  • Page 14 24LC08B (EEPROM) (1) Features • Single supply with operation down to 2.5V • Page-write buffer for up to 16 bytes • Low power CMOS technology • 2ms typical write cycle time for page-write - 1mA active current typical • Hardware write protect for entire memory - 10 A standby current typical at 5.5V •...
  • Page 15 TDA8374A (Single chip TV Processor for Negative modulation IF ) TDA8374 (Single chip TV Processor for Negative & positive modulation IF) (1) General Description The TDA8374(A) is I2C-bus controlled single chip TV processors which are intended to be applied in PAL/NTSC television receiver.
  • Page 16 (3) Block Diagram...
  • Page 17 (4) Pin Description Name Description SOUND IF INPUT The sound equivalent input impedance is 8k5 ohm // 5pF which has to be taken into account for proper termination of the ceramic filters. The DC impedance is very high. The minimum input signal for catching is l mV rms. EXT AUDIO INPUT An external sound signal (500mVrms) for example from SCART can be applied to this pin via a coupling capacitor.
  • Page 18 Name Description A voltage detection circuit is connected to both pins. - pin12 if V12 <6.8V than a power on reset, POR, is generated. The Hout output is disabled immediate. - pin37 if V37 <5.8V than the horizontal output is disabled immediate. INT CVBS INPUT It is recommended that the CVBS1 int and CVBS2 ext input amplitudes are EXT CVBS INPUT...
  • Page 19 Name Description to the luminance input pin 27. The pin is internally AC coupled to the luminance clamp via a capacitor of 50pF; clamping action occurs during burstkey period. LUMINANCE The luminance output signal is approximately l V black-white with typical OUTPUT output impedance of 25O ohm.
  • Page 20 Name Description A flash protection becomes active when this pin is forced >6V. The horizontal drive is switched-off immediately. Once the voltage is <6V the horizontal drive is switched-on again via the slow start procedure. PHI-1 FILTER The loopfilter connected to pin 43 is suitable for various signal conditions as strong/weak and VCR signal.
  • Page 21 TDA4665(Base Band Delay Line) (1) Features • Two comb filters, using the switched-capacitor technique,for one line delay time (64µs) • Adjustment free application • No crosstalk between SECAM colour carriers • Handles negative or positive colour-difference input signals • Clamping of AC-coupled input signals(±(R-Y)and±(B-Y)) •...
  • Page 22 TDA8395 (Secam Decoder) (1) Features Fully integrated filters Alignment free For use with baseband delay (2) Description The TDA8395 is a self-calibrating,fully integrated SECAM decoder. The IC should preferably be used in conjunction with the PAL/NTSC decoder TDA8362 and with the switch capacitor baseband delay circuit TDA4665.
  • Page 23 TDA6106Q ( Video Output Amplifier ) (1) General Description The TDA6106Q is a monolithic video output amplifier (5MHz bandwidth) in a SIL 9 MPpackage, using high-voltage DMOS technology, and is intended to drive the cathode of CRT directly . To obtain maximum performance, the amplifier should be used with black-current control. (2) Feature •...
  • Page 24 I802 PC817 (1) General Description The specification applies to the structures and characteristics of Model No. PC817 (2) Block Diagram (3) Absolute maximum ratings Parameter Symbol Rating Unit Forward current *1) Peak forward current Input Reverse voltage Power dissipation Collector-emitter voltage VCEO Output Emitter-collector voltage...
  • Page 25 TDA8356 (DC-coupled vertical deflection circuit) (1) General Description The TDA8356 is power circuit for use in 90 and 110 color deflection systems for field frequencies of 50 to 120 Hz. The circuit provides a DC driven vertical deflection output circuit, operating as a high efficient class G system. (2) Feature •...
  • Page 26 TDA7056 (BTL AUDIO OUTPUT AMPLIFIER) : 1 SPEAKER MODEL (1) Features • No external components • No switch-on/off clicks • Good overall stability • Low power consumption • Short circuit proof • ESD protected on all pins (2) General Description The TDA7056 is a mono output amplifier contained in a 9 pin medium power package.
  • Page 27 STR-S5707 (Hybrid IC for a Switching Regulator) (1) General Description The STR-S5707 is a Hybrid IC with a built in power transistor and a separate excitation control IC, designed for converter type switching mode power supply applications. The IC is capable of quasi-resonant mode and requires small number of external component. (2) Feature •...
  • Page 28 Electrical Characteristics of Control Part (Ta=25 ) Description Terminal Symbol Rating Unit On-state Voltage IN(ON) Off-state Voltage IN(OFF) Operating Circuit Current IN(ON) Stand-by Circuit Current IN(OFF) On Time Off Time OCP terminal Threshold Voltage -1.12 -0.88 INH terminal Threshold Voltage 1 0.65 0.75 0.85 INH-1...
  • Page 29 TDA8138 (5.1V+12V regulator with Disable and Reset) (1) General Description The TDA8138 is a monolithic dual positive voltage regulator designed to provide fixed precision output voltages of 5.1V and 12V at currents up to 1A. A internal reset cuicuit generates a reset pulse when the output 1 decrease below the regulated voltage value. Output 2 can be disabled by TTL input.
  • Page 30 TDA 1519B(AUDIO OUTPUT AMPLIFIER); 2 SPEAKER MODEL (1) Features • Requires very few external components for • AC and DC short-circuit-safe to ground and Vp Bridge Tied Load(BTL) • Thermally protected • Stereo ot BTL application • Reverse polarity safe •...
  • Page 31 PCA84C 122A(IC REMOCON) (1) Features • ROM, RAM and I/O is device dependent • Two test inputs T0, T1 • 3 Single-level vectored interrupt sources • 8 bit programmable timer/counter with 5-bit pre-scaler • Single supply voltage from 2.0V to 5.5V •...

  • Page 32: Circuit Description

    Circuit Description Vision IF amplifier, AFC, video demodulator The IF signal from the tuner is fed through a SAW filter to the differential IF input (pin 48 and 49). The first IF stage consists of 3 AC-coupled amplifiers with a total gain control range of over 66 dB. The reference carrier for the video demodulator is obtained by a PLL carrier regenerator (eliminating notch filter compromises, as in reference tuned circuits for passive carrier regeneration).
  • Page 33 This compensates for the storage time of the horizontal deflection transistor. - 2 loop filter (C) is externally connected to pin 42. The horizontal phase can be given a static off set via I2C-but (HSH “horizontal shift”) A dynamic correction is possible by current feedback into the - 2 loop filter capacitor.
  • Page 34 Integrated video filters The TDA8374 has alignment-free internal luminance delay, chroma bandpass and chroma trap. They are implemented as gyrator circuits tuned by tracking to the frequency of the chroma Xtal oscillator. The chroma trap in the Y signal path is by-passed when Y/C input is selected (S-VHS ). For SECAM an extra luminance delay is build-in, for correct delay of the luminance signal.
  • Page 35 TDA8395 SECAM decoder The TDA8395 is an alignment-free SECAM colour decoder, including a Cloche filter, demodulator and line identification circuit. The Cloche filter is a gyrator-capacitor type. Its frequency is calibrated in the vertical retrace period. The calibration reference( pin 1 ) is obtained from the TDA8374 color X-tal oscillator (pin 33). Pin 7 is a decoupling for the Cloche reference.
  • Page 36 TDA8356 vertical deflection. The TDA8356 is a vertical deflection circuit. It can be used in 90 deflection systems with frame frequencies from 50 up to 120 Hz With its bridge configuration the deflection output can be DC coupled with few external components. Only a supply voltage for the scan and a second supply for the flyback are needed.
  • Page 37 Video amplifiers Three TDA6106Q integrated video amplifiers drive cathode of the picture tube directly. They are protected against CRT flashover discharges and ESD (electro static discharge). The three video amplifiers, have a beam current output I black, used by the TDA8374 black current loop to control the black level on the cathodes.
  • Page 38 Stand-By Mode While being in remote control stand-by mode, the output voltage is kept on providing to the secondary side and the power transistor operates at A class mode. By connecting INH terminal (Pin 6) to the GND, the OFF-time of the power transistor is fixed at set time = 50usec at Ta = 25 ) of the built-in oscillator, and only ON-time changes depending on input and output conditions of the power supply.
  • Page 39 Trouble Shooting Charts 1. NO RASTER CHECK MAIN B+(+123V/+110V) LINE ABNORMAL NORMAL CHECK VOLTAGE AT CHECK HEATER VOLTAGE, (+) OF C807(220 F 400V) VIDEO B+(200V) LINE, 310Vdc AT AC 220V 16.5V & 48V LINE NORMAL ABNORMAL NORMAL ABNORMAL CHECK / REPLACE CHECK HORIZONTAL CHECK / REPLACE F801 I801(STR-S5707)
  • Page 40 2. NO PICTURE(RASTER OK) CHECK VIDEO SIGNAL AT PIN 13 OF I501(TDA8374A) [REFER TO WAVEFORM ABNORMAL NORMAL CHANGE INPUT MODE CHECK WAVEFORM AT RF AV RF PIN 29, PIN 30 OF I501 CHECK / REPLACE I701 ABNORMAL ABNORMAL NORMAL ABNORMAL &...
  • Page 41 3. NO VERTICAL SCANING(ONE HORIZONTAL LINE ON SCREEN) CHECK / REPLACE P401 & DY CHECK VERTICAL Vcc +16.5V AT PIN3 & +48V AT PIN6 OF I301(TDA 8356) NORMAL ABNORMAL CHECK SIGNAL CHECK / REPLACE AT PIN1 & PIN2 D401(BYV95C) OF I301 [REFER TO D409(BYV95C) WAVEFORM R303(1W 15K)
  • Page 42 4. NO COLOR CHECK VIDEO SIGNAL AT PIN13 OF I501(TDA8374A) [REFER TO WAVEFORM REFER TO ABNORMAL NO PICTURE CHART NORMAL CHECK SYSTEM MODE AUTO PAL SECAM N3 N4 N5 CHECK SIGNAL AT PIN29, PIN30 OF I501 ABNORMAL NORMAL CHECK / REPLACE CHECK / REPLACE I501 X501(4.43MHz X-TAL) X502(3.58MHz x-tal)
  • Page 43 5. NO SOUND(PICTURE OK) CHECK AUDIO SIGNAL AT PIN15 OF I501 ABNORMAL CHECK MUTE VOLTAGE AT PIN20 OF I701 *MUTE : HIGH ABNORMAL NORMAL CHECK SIF SIGNAL CHECK /REPLACE AT PIN1 OF I501 R619, C602, Q604 D605, Q606, I701 ABNORMAL NORMAL CHECK SIGNAL WAVEFORM CHECK / REPLACE I501...
  • Page 44 6. NO EXTERNAL A/V(RF OK) CHECK EXTERNA AUDIO & VIDEO SIGNAL AT PIN2 & 17 OF I501 RESPECTIVELY ABNORMAL NORMAL CHECK WAVEFORM CHECK RCA JACK AT PIN7 & 8 OF I501 ABNORMAL CHECK / REPLACE I701 CHECK / REPLACE I501 7.
  • Page 45 8. REMOTE CONTROL UNIT TROUBLE(LOCAL CONTROL OK) CHECK PULSE AT COLLECTOR OF Q1(TRANSMITTER BOARD) ABNORMAL CHECK / REPLACE CHECK PULSE Q1 / LED1 AT PIN36 OF I701 (TRANSMITTER BOARD) CHECK IC1 (DHR-001S) ABNORMAL NORMAL CHECK / REPLACE CHECK / REPLACE CHECK / REPLACE I701 &...
  • Page 46 IC DC Voltage Charts • Input signal - Video : color BAR(PM5518)-PAL -Audio : 1khz sine wave • User’s control condition - Contrast, Brightness, Color, Volume(Normal condition) • Line Voltage - AC 220V, 50HZ • All the Voltage in each point are measured with multimeter •...
  • Page 47 • I501(TDA8374A) PIN NO V(DC) 6.64 8.0 100mv PIN NO V(DC) 3.76 PIN NO V(DC) PIN NO V(DC) • I301(TDA8356) PIN NO V(DC) 16.8 • I502(TDA4665) PIN NO V(DC) • I503(TDA8395) PIN NO V(DC) • I802(TDA8138) PIN NO V(DC) 13.0 14.0 4.82 5.05...

  • Page 48: Electrical Part List

    DTC-14Q1VM 6520010100 STAPLE PIN 18M/M J D O 6520010200 STAPLE PIN #3417 M801 485803871D BOX CARTON SW-2 M811 4858179200 EPS 14Q1 M821 4858210702 BAG P.E L.D.P.E T0.03X1150X1000 M822 4858211400 POLY BAG P.E FILM T0.03X600X550 2TF01612CL TAPE FILAMENT 12MMX55ME CLEAR ZZ131...
  • Page 49 LOC. PART-CODE PART-NAME PART TYPE REMARK ZZ220 PTSPPWA499 SPEAKER AS DTC-14Q1VM PA601 4850703S03 CONN AS YH025-03+YST025+ULW=200 SP01 4858306810 SPEAKER 3W 16 OHM F2035C03-3 ZZ290 PTMPMSA499 PCB MAIN MANUAL AS DTC-14Q1VM 2193102005 SOLDER BAR SN:PB=63:47 S63S-1320 2193011101 SOLDER WIRE RS 60-1.2 1.6A 2291050615 FLUX SOLDER DF-2012U...
  • Page 50 LOC. PART-CODE PART-NAME PART TYPE REMARK I901 1TDA6106Q- IC AMP TDA6106Q I902 1TDA6106Q- IC AMP TDA6106Q I903 1TDA6106Q- IC AMP TDA6106Q JA01 WP-1BK1715 WIRE LEAD 1007 AWG22 1/0.65 BK 5-170-5 JA02 WP-1BK1715 WIRE LEAD 1007 AWG22 1/0.65 BK 5-170-5 JV03 4859104250 JACK PIN BOARD YSC-0406(YW+YW+RD+RD)
  • Page 51 LOC. PART-CODE PART-NAME PART TYPE REMARK Z503 5PTPS60MB- FILTER CERA TPS 6.0MB(EFC-S6ROME3) Z504 5PTPS65MB- FILTER CERA TPS 6.5MB(EFC-S6R5ME3) ZZ200 PTMPJ0A499 PCB MAIN (RHU) AS DTC-14Q1VM C308 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16) TP C412 CEXF2C339V C ELECTRO 160V RSS 3.3MF (8X16) TP C417 CEXF2E330V C ELECTRO...
  • Page 52 LOC. PART-CODE PART-NAME PART TYPE REMARK C115 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP C116 CMXM2A223J C MYLAR 100V 0.022MF J TP C117 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C119 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C301 CMXB1H104J C MYLAR 50V EU 0.1MF J (TP)
  • Page 53 LOC. PART-CODE PART-NAME PART TYPE REMARK C702 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP C706 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C707 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11) TP C710 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C711 CMXM2A104J C MYLAR...
  • Page 54 LOC. PART-CODE PART-NAME PART TYPE REMARK Q507 TKTA1266Y- KTA1266Y (TP) Q601 TKTC3198Y- KTC3198Y Q602 TKTC3198Y- KTC3198Y Q603 TKTC3198Y- KTC3198Y Q604 TKTC3198Y- KTC3198Y Q605 TKTC3198Y- KTC3198Y Q606 TKTA1266Y- KTA1266Y (TP) Q702 TKTC3202Y- KTC3202Y (TP) Q703 TKTC3198Y- KTC3198Y Q705 TKTC3198Y- KTC3198Y Q706 TKTC3198Y- KTC3198Y Q707...
  • Page 55 LOC. PART-CODE PART-NAME PART TYPE REMARK C122 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z (AXIAL) C302 CCZB1H181K C CERA 50V B 180PF K (AXIAL) C303 CCZB1H181K C CERA 50V B 180PF K (AXIAL) C401 CBZR1C472M C CERA 16V Y5R 4700PF M (AXIAL) C403 CBZR1C222M C CERA...
  • Page 56 LOC. PART-CODE PART-NAME PART TYPE REMARK DA04 DUZ9R1BM— DIODE ZENER UZ-9.1BM 9.1V DA06 DUZ9R1BM— DIODE ZENER UZ-9.1BM 9.1V DA09 DUZ9R1BM— DIODE ZENER UZ-9.1BM 9.1V DO401 DUZ5R1BM— DIODE ZENER UZ-5.1BM D102 D1N4148—- DIODE 1N4148 (TAPPING) D301 DUZ5R1BM— DIODE ZENER UZ-5.1BM D401 DBYV95C—- DIODE BYV95C (TAPPING)
  • Page 57 LOC. PART-CODE PART-NAME PART TYPE REMARK D813 DBYV95C—- DIODE BYV95C (TAPPING) D814 DBYV95C—- DIODE BYV95C (TAPPING) L101 5CPZ100K04 COIL PEAKING 10UH 10.5MM K (LAL04TB) L103 5CPZ220K02 COIL PEAKING 22UH K (AXIAL 3.5MM) L401 5CPZ109M02 COIL PEAKING 1UH M (AXIAL 3.5MM) L501 5CPZ150K02 COIL PEAKING...
  • Page 58 LOC. PART-CODE PART-NAME PART TYPE REMARK R310 RD-4Z392J- R CARBON FILM 1/4 3.9K OHM J R311 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R312 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R313 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R314 RD-4Z223J- R CARBON FILM...
  • Page 59 LOC. PART-CODE PART-NAME PART TYPE REMARK R530 RD-AZ203J- R CARBON FILM 1/6 20K OHM J R531 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J R532 RD-AZ361J- R CARBON FILM 1/6 360 OHM J R533 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J R534 RD-AZ103J- R CARBON FILM...
  • Page 60 LOC. PART-CODE PART-NAME PART TYPE REMARK R703 RD-AZ272J- R CARBON FILM 1/6 2.7K OHM J R705 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R708 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R709 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R710 RD-AZ100J- R CARBON FILM...
  • Page 61 LOC. PART-CODE PART-NAME PART TYPE REMARK R762 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R763 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R764 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R765 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R766 RD-AZ104J- R CARBON FILM...
  • Page 62 LOC. LOC. PART-CODE PART-CODE PART-NAME PART-NAME PART-DESCRIPTION PART-DESCRIPTION REMARK REMARK R625 RD-AZ221J- R CARBON FILM 1/4 220 OHM J R628 RD-AZ221J- R CARBON FILM 1/4 220 OHM J C621 CEXF1E470V C ELECTRO 25V RSS 47MF C623 CEXF1E470V C ELECTRO 25V RSS 47MF P603 4859231725 CONN WAFER...
  • Page 63 Q / T Difference Part List PART NAME Q MODEL(1spk) T MODEL(2spk) I601 IC AMP TDA 7056 TDA 1519B I601A HEAT SINK 4857025400(A1050P-H24 T2) 4857026402(AL EX BK) PA601 CONN AS YH025-03+YST025+ULW=200 YH025-03+YST025+ULW=300 PA602 CONN AS YH025-03+YST025+ULW=600 SP01 SPEAKER 3W 16 F2035C03-3 7.5W 8 95BF03LC SP02 SPEAKER...

  • Page 64: Inch Difference Part List

    CP-370 Inch Difference Part List PART NAME 14” MODEL 20” MODEL 21” MODEL REMARK R407 R-CARBON 1/4W 82K 1/4W 68K 1/4W 68K C410 C-MYLAR 1.6KV 6900PF 1.6KV 7500PF J 1.6KV 6000PF C411 C-MYLAR 200V 0.33MF J 200V 0.36MF J 200V 0.3MF R415 R-FUSIBLE 1W 1.2OHM...

This manual is also suitable for:

14q214t114q314t214t320q1 ... Show all