Page 1
27 ” Digital / Analog Television Owner’s Manual CR270TT8 TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA. IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-844-5001.
NTRODUCTION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
15. POWER LINES - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
NTRODUCTION LOCATION For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. •...
Features • DTV/TV/CATV - You can use your remote control to select channels which are broadcast in digital, conventional analog, standard definition. Also, cable subscribers can access their cable TV channels. • Program Information Display (DTV only) - You can display the title, contents and other information of the current DTV program on the TV screen.
NTRODUCTION Remote Control Function POWER AUDIO INFO CHANNEL – /ENT RETURN INPUT MENU SLEEP MUTE SELECT Installing the Batteries Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control. Battery Precautions: • Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device. •...
Control Panel Y VOLUME X L CHANNEL K MENU VIDEO L - AUDIO - R Rear Panel DIGIT A L VIDEO AUDIO OUTPUT AUDIO S-VIDEO INPUT ANT. IN COMPONENT INPUT VIDEO-1 INPUT DIGITAL AUDIO VIDEO OUTPUT AUDIO S-VIDEO ANT. IN INPUT COMPONENT INPUT VIDEO-1 INPUT...
ONNECTION Cables not included. Please purchase the necessary cables at your local store. Basic Connection This section describes how to connect the unit to an antenna, cable/satellite box, etc. Note: • Be sure your antenna or other device is connected properly before plugging in the power cord. [Antenna Cable Connection] When connecting the unit to an antenna or cable TV company (without cable/satellite box) Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
Cables not included. Please purchase the necessary cables at your local store. External Device Connection [Component Connection] This is the best method to connect this TV to video devices with the component output jack, such as DVD player, etc. It can minimize the deterioration of image quality. Use the component cable for connection.
NITIAL SETTING These operations are accessible by remote control. Some may also be accessible by controls on the main unit. Initial Setup This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and “AUTO PRESET CH”, which automatically scans and memorizes viewable channels.
• ENG/ESP/FRA You can change the language (English, Spanish, French) displayed on the main menu. (Refer to “Language Selection” on page 11.) • V-CHIP SET UP You can set the viewing limitations. (Refer to “V-chip” on page 20.) • CAPTION You can change the display format for closed caption, which displays the dialogue of a TV program or other information across the TV screen.
ATCHING TV Channel Selection Select channels by pressing [CH K /L] or [the Number buttons]. • To select the memorized channels, use [CH K/L] or [the Number buttons]. • To select the non-memorized channels use [the Number buttons]. To Use [the Number buttons] - When selecting analog channel 12 - When selecting digital channel 12-1 Be sure to press [–/ENT] before entering the minor...
Accessing External Devices Use your remote control to access an external device when they are connected to the unit. Press [INPUT SELECT] repeatedly to cycle through analog TV, digital TV, VIDEO1 and VIDEO2. INPUT SELECT • To use the video or S-video input jack on the rear of the unit, select “VIDEO1”.
ATCHING TV In the digital mode, the detailed broad casting information for the current channel such as program title, the program guides are displayed. Press [INFO] repeatedly to cycle through the available display modes. INFO INFO [BROADCASTING INFORMATION] [PROGRAM GUIDE] [Broadcasting Information] •...
Sleep Timer The sleep timer can be set to automatically turn off the unit after an incremental period of time. Press [SLEEP] to set the sleep timer. SLEEP • Sleep timer display appears on the TV screen. Press [SLEEP] repeatedly to change the amount of time until shut off.
PTIONAL SETTING Channel Add/Delete The channel add/delete function lets you add the channel that was not added by the auto channel scan due to the reception status at the initial setting. You can also delete the unnecessary channels. Press [MENU] to display the main menu. MENU Use [CH K/L] to select “CHANNEL SET”, then press [VOL X ].
Picture Adjustment You can adjust brightness, contrast, color, tint and sharpness. Press [MENU] to display the main menu. MENU Use [CH K /L] to select “PICTURE”, then press [VOL X]. e.g.) digital TV mode PICTURE CHANNEL SET [ENG]/ESP/FRA V-CHIP SET UP CAPTION [OFF] DTV SET UP Use [CH K /L] to select the picture quality type you...
PTIONAL SETTING Press [MENU] to exit. MENU Note: • To show the closed caption on your TV screen, broadcast signal must contain the closed caption data. • Not all TV programs and commercials have the closed caption or all types of the closed caption. •...
Page 19
[CAPTION SERVICE] [OFF] [SERVICE1/6] [SERVICE2/6] [SERVICE3/6] [SERVICE4/6] [SERVICE5/6] [SERVICE6/6] OFF: Select if you do not want DTVCC. This is the default. SERVICE 1 to SERVICE 6: Select one of these before changing any other item in “CAPTION” menu. Choose “SERVICE1/6” under normal circumstances.
PTIONAL SETTING [FORE COLOR] Font color of the displayed caption can be switched as below. [TRANSPARENT] [BACK OPACITY] Background opacity of the displayed caption can be switched as below. [TRANSLUCENT] [BACK COLOR] Background color of the displayed caption can be switched as below.
Page 21
A. TV Rating Use [CH K /L] to select “TV RATING“, then press [VOL X]. e.g.) analog TV mode TV RATING MPAA RATING CHANGE CODE Use [CH K /L ] to select the desired rating, then press [VOL X] repeatedly to switch between “VIEW”...
Page 22
PTIONAL SETTING B. MPAA Rating MPAA Rating is the rating system created by MPAA (Motion Picture Association of America). Use [CH K /L] to select “MPAA RATING”, then press [VOL X]. e.g.) analog TV mode TV RATING MPAA RATING CHANGE CODE Use [CH K /L], then press [VOL X] repeatedly to change the setting.
D.S.T. After the initial setting you set when you fi rst turned on the power, you can set the D.S.T. (daylight saving time) again. When you set this function to ON, the clock will automatically move forward one hour at 2:00 a.m on the fi rst Sunday in April and move back one hour at 2:00 a.m on the last Sunday in October.
ROUBLESHOOTING Troubleshooting Guide If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service. Symptom No power No picture or sound No color Sound OK, picture poor Picture distorted Weak picture Lines or streaks in picture...
Page 25
Symptom Remedy The entered channel number • Many digital channels have alternate channel numbers. The unit changes the changes automatically numbers automatically to the ones signifying the broadcasting stations. These are the numbers used for analog broadcasts. Remote control does not work •...
NFORMATION Glossary Access Code A stored 4-digit number that allows access to parental control features. Aspect Ratio The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the TV screen is almost square); widescreen models are 16:9 (the TV screen is almost twice as wide as its height).
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase.
Page 29
PARA RECIBIR LA SEÑAL DIGITAL/ANALÓGICA, DEBE CONECTAR LA ANTENA. SI NECESITA AYUDA ADICIONAL CON LA INSTALACIÓN O CON EL FUNCIONAMIENTO DESPUÉS DE LEER EL MANUAL DEL USUARIO, LLAME AL TELÉFONO GRATUITO 1-800-844-5001. Televisión Digital / Analógica de 27 Pulgadas Manual del Usuario CR270TT8...
NTRODUCCIÓN ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE APARATO A LLUVIA O HUMEDAD. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CUIDADO: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PLACA TRASERA). EL INTERIOR DE ESTE APARATO NO CONTIENE PIEZAS REPARABLES POR EL USUARIO.
15. LÍNEAS DE CONDUCCIÓN ELÉCTRICA - Un sistema de antena exterior no debe colocarse en las proximidades de líneas de conducción eléctrica aéreas u otras líneas de conducción de circuitos eléctricos, o de manera que puedan caer sobre dichas líneas o circuitos eléctricos. Cuando se instale un sistema de antena exterior, debe tenerse el máximo cuidado para no tocar dichas líneas o circuitos eléctricos, dado que el contacto podría resultar mortal.
NTRODUCCIÓN UBICACIÓN Para un funcionamiento seguro y un rendimiento satisfactorio del aparato, tenga en cuenta lo siguiente a la hora de seleccionar un lugar para su instalación: • Debe protegerlo de la luz solar directa y mantenerlo apartado de fuentes de calor intenso. •...
Características • DTV/TV/CATV - Puede utilizar su mando a distancia para seleccionar canales emitidos en formato digital, analógico convencional, definición estándar y alta definición. Además, los suscriptores de cable pueden acceder a sus canales de televisión por cable. • Pantalla de Información de Programas (solamente DTV) - Puede visualizar el título, el contenido y otra información del actual programa DTV en la pantalla del televisor.
NTRODUCCIÓN Función de Mando a Distancia POWER AUDIO INFO CHANNEL – /ENT RETURN INPUT MENU SLEEP MUTE SELECT Instalación de las Pilas Instale las pilas (AA x 2) de manera que coincida la polaridad indicada en el interior del compartimento de las pilas del mando a distancia.
Panel de Control Y VOLUME X L CHANNEL K MENU VIDEO L - AUDIO - R Panel Trasero DIGIT A L VIDEO AUDIO OUTPUT AUDIO S-VIDEO INPUT ANT. IN COMPONENT INPUT VIDEO-1 INPUT DIGITAL AUDIO VIDEO OUTPUT AUDIO S-VIDEO ANT. IN INPUT COMPONENT INPUT VIDEO-1 INPUT...
ONEXIÓN Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. Conexión Básica En esta sección se describe cómo conectar el aparato a una antena, caja de cable/satélite, etc. Nota: • Asegúrese de que su antena u otro dispositivo está conectada correctamente antes de enchufar el cable de alimentación. [Conexión de Cable de Antena] Cuando conecte el aparato a una empresa de televisión por antena o cable (sin caja de cable/satélite) Conecte el cable coaxial RF de su toma de corriente a la toma de entrada de antena de este aparato.
Cables no incluidos. Deberá adquirir los cables necesarios en su establecimiento local. Conexión de Dispositivo Externo [Conexión De Componente] Este es el mejor método para conectar el TV a los equipos de vídeo con la clavija de salida del componente, como el reproductor de DVD, etc.
JUSTE INICIAL Se puede acceder a estas operaciones mediante el mando a distancia. Algunas también pueden ser accesibles mediante los mandos del aparato principal. Configuración Inicial Esta sección le guiará a través del ajuste inicial del aparato, que incluye la selección de un idioma para sus menús de pantalla y “PREA.
• ESP / FRA / ENG Puede cambiar el idioma (Español, Francés, Inglés) visualizado en el menú principal. (Consulte “Selección de Idioma” en página 11.) • AJUSTE DE V-CHIP Puede ajustar las limitaciones de visión. (Consulte “V-chip” en página 20.) •...
ARA VER LA TELEVISIÓN Selección de Canal Seleccione los canales presionando [CH K /L] o [los botones numéricos]. • Para seleccionar los canales memorizados, utilice [CH K/L] o [los botones numéricos]. • Para seleccionar los canales no memorizados, utilice [los botones numéricos]. Para utilizar [los botones numéricos] - Cuando seleccione el canal analógico 12 - Cuando seleccione el canal digital 12-1...
Acceso a Dispositivos Externos Utilice su mando a distancia para acceder a un dispositivo externo cuando esté conectado al aparato. Presione [INPUT SELECT] repetidamente para cambiar entre TV analógica, TV digital, VIDEO1 y VIDEO2. INPUT SELECT • Para utilizar la toma de entrada de vídeo o de S-Video, en la parte posterior del aparato, seleccione “AUX1”.
ARA VER LA TELEVISIÓN En el modo digital, se muestra la información detallada de emisión del canal actual, por ejemplo el título de programa y las guías de programas. Presione [INFO] repetidamente para recorrer los modos de visualización disponibles. INFO INFO [INFORMACIÓN DE EMISIÓN] [GUÍA DE PROGRAMAS]...
Temporizador de Apagado El temporizador de apagado puede confi gurarse para apagar automáticamente el aparato después de un periodo incremental de tiempo. Presione [SLEEP] para ajustar el temporizador de apagado. SLEEP • El temporizador de apagado aparece en la pantalla del televisor.
JUSTE OPCIONAL Agregar/Borrar Canales La función de agregar/borrar canales le permite agregar el canal que no se haya agregar mediante la exploración automática de canales debido al estado de la recepción en el ajuste inicial. También puede eliminar los canales innecesarios. Presione [MENU] para visualizar el menú...
Ajuste de Imagen Puede ajustar el brillo, el contraste, el color, el matiz y la nitidez. Presione [MENU] para visualizar el menú principal. MENU Utilice [CH K /L] para seleccionar “IMAGEN”, y presione [VOL X]. p. ej.: modo TV digital IMAGEN CANAL PREP.
JUSTE OPCIONAL Presione [MENU] para salir. MENU Nota: • Para mostrar los subtítulos cerrados en la pantalla de su televisor, la señal de emisión debe contener los datos de los subtítulos cerrados. • No todos los programas y anuncios de TV contienen subtítulos cerrados o todo tipo de subtítulos cerrados.
Page 47
[SERVICIO TITULO] [OFF] [SIRVE1/6] [SIRVE2/6] [SIRVE3/6] [SIRVE4/6] [SIRVE5/6] [SIRVE6/6] OFF: Selecciónelo si no desea DTVCC. Éste es el ajuste predeterminado. SIRVE 1 a SIRVE 6: Seleccione uno de ellos antes de cambiar cualquier otro elemento del menú “TITULO”. Seleccione “SIRVE 1/6”...
JUSTE OPCIONAL [COLOR ADELANTE] El color de fuente del subtítulo mostrado puede elegirse entre los siguientes. [TRANSPARENTE] [OPACO ATRÁS] La opacidad de fondo del subtítulo mostrado puede elegirse entre las siguientes. [TRANSLUCIDA] [COLOR FONDO] El color de fondo del subtítulo mostrado puede elegirse entre los siguientes.
Page 49
A. Clase de TV Utilice [CH K /L] para seleccionar “CLASE DE TV”, y presione [VOL X]. p. ej.: modo de televisión analógica CLASE DE TV CLASE DE MPAA CAMBIAR CODIGO Utilice [CH K /L ] para seleccionar la clasificación deseada y luego presione [VOL X] repetidamente para cambiar entre “MIRAR”...
Page 50
JUSTE OPCIONAL B. Clase de MPAA Clase de MPAA es el sistema de clasifi cación creado por la MPAA (Motion Picture Association of America). Utilice [CH K /L] para seleccionar “CLASE DE MPAA” y luego presione [VOL X]. p. ej.: modo de televisión analógica CLASE DE TV CLASE DE MPAA CAMBIAR CODIGO...
Hora de Verano Después de realizar los ajustes iniciales al encender por primera vez la corriente, podrá establecer de nuevo la hora de verano. Cuando esta función está en ON, el reloj avanza automáticamente una hora a las 2:00 a.m. del último domingo de octubre.
OLUCIÓN DE PROBLEMAS Guía de Solución de Problemas Si el aparato no funciona correctamente cuando se siguen las instrucciones de este manual del usuario, compruebe la siguiente tabla antes de llamar al servicio técnico. Síntoma No hay corriente No hay imagen ni sonido No hay color Sonido correcto, imagen deficiente...
Page 53
Síntoma Solución Recepción deficiente en • Compruebe la conexión de antena o de cable con el aparato principal. determinados canales • Cuando se utilice la antena exterior, compruebe el estado del cable y de la conexión. • La interferencia eléctrica de aparatos cercanos puede afectar a la calidad de la imagen.
NFORMACIÓN Glosario ATSC Acrónimo de Advanced Television Systems Committee (Comité de sistemas avanzados de televisión) y el nombre de unas normas de emisión digital. Contraseña Un número almacenado de 4 dígitos que permite el acceso a las funciones de control parental.
(1) año desde la fecha de compra minorista original. Dos (2) años para tubo de imagen. Determinadas piezas están excluidas de esta garantía. MANO DE OBRA: FUNAI CORP. suministrará la mano de obra de forma gratuita durante un periodo de noventa (90) días desde la fecha de compra minorista original.