RF-TVML70 TV Wall Mount Safety information and specifications .........2 Tools needed.................2 Package contents: parts ............3 Package contents: hardware ...........4 Installation instructions.............5 For wood-stud and concrete wall installations Assembly Guide Before using your new product, please read these instructions to prevent any damage.
The weight of your TV must not exceed 70 lbs. (31.8 kg). Rocketfish recommends that the wall be capable of supporting five times the weight of your TV and wall mount combined, or approximately 350 lbs. (159 kg).
C Horizontal rails (4) B Vertical rails (2) D Template (1) E VESA adapters (2) Dessus Dessus Parte superior RF-TVML70 Template • Gabarit • Plantilla Parte superior Tools Needed Outils nécessaires Herramientas requeridas 5.47" (139.0 mm) Note Remarque : Pour une construction à ossature de bois, localiser d'abord les montants en bois, à...
RF-TVML70 TV Wall Mount Package contents: hardware Make sure that you have all the hardware necessary to assemble your new TV wall mount: Label Hardware Qty. Label Hardware Qty. M4 × 15 mm screw Button head screw M4 × 30 mm...
RF-TVML70 TV Wall Mount Installation instructions STEP 1 - Determine whether you need the optional VESA adapters Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions.
Page 6
RF-TVML70 TV Wall Mount STEP 2 - Determine whether your TV has a flat back or an irregular or obstructed back Temporarily lay the vertical rails (B) on the back of your TV. Align the screw holes in the vertical rails or VESA adapters with the mounting screw holes on your TV.
Page 7
RF-TVML70 TV Wall Mount STEP 3 - Select screws, washers, and spacers Select the screws for your TV. A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are usually in the holes on the back of the TV.) If you don't know the correct length and diameter of the mounting screws your TV requires, test various sizes by hand threading the screws.
Page 8
RF-TVML70 TV Wall Mount STEP 4: Option 1- Attaching the vertical rails to the TV Align the vertical rails (B) with the screw holes on the back of the TV. Install the screws you identified in Step 2 (M-A, M-B, M-C, M-D, M-E, M-F, M-G, or M-H) securely into the four holes in the back of the TV, using washers (M-K or M-L) and spacers (M-I or M-J) as necessary.
Page 9
RF-TVML70 TV Wall Mount STEP 4: Option 2- Attaching the vertical rails and adapters to the TV Align the vertical rails (B) with the VESA adapters (E) with the screw holes on the back of the TV. Install the screws you identified in Step 2 (M-A, M-B, M-C, M-D, M-E, M-F, M-G, or M-H) securely into the four holes in the back of the TV, using washers (M-K or M-L) and spacers (M-I or M-J) as necessary.
Page 10
RF-TVML70 TV Wall Mount STEP 5 - Determine wall-mount location Notes: • For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder • Your TV should be high enough so your eyes are level with the middle of the screen. Normally, 40 to 60 inches from the ground.
Page 11
RF-TVML70 TV Wall Mount STEP 6 - Option 1: Installing on a wood stud wall Note: Any wallboard or material covering the wall must not exceed 5/8" (16 mm). Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.
Page 12
RF-TVML70 TV Wall Mount STEP 6 - Option 1: (continued) You’ll need Dessus Dessus Parte superior RF-TVML70 Template • Gabarit • Plantilla Parte superior Tools Needed Outils nécessaires W-A (2) Herramientas requeridas 5.47" (139.0 mm) Note Remarque : Pour une construction à ossature de bois, localiser d'abord les montants en bois, à...
Page 13
CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (W-A). 3.18 in. (80 mm) You’ll need Dessus Dessus Parte superior RF-TVML70 Template • Gabarit • Plantilla Parte superior Tools Needed Outils nécessaires Herramientas requeridas 5.47" (139.0 mm) W-A (2) Note Remarque : Pour une construction à...
RF-TVML70 TV Wall Mount STEP 7 - Attach the horizontal rails to the lift assembly Using the 4 mm Allen wrench (P-B), install the right and left horizontal rails (C) onto the lift assembly (A) using four button head screws (P-A) for each horizontal rail.
Page 15
RF-TVML70 TV Wall Mount STEP 8 - Attach your TV to the lift assembly Hang the hooks of the vertical rails (B) over the top horizontal rails (C), then lower the bottom tabs of the vertical rails (B) under the bottom horizontal rail (C).
RF-TVML70 TV Wall Mount STEP 9 - Installing the cable wrap and cable ties Connect the cable to your TV, then secure the cable to the lift assembly (A) with cable ties (G) or cable clips (H), as necessary. Install the cable tubing (E) on the cables to provide a neater appearance.
Page 17
RF-TVML70 TV Wall Mount STEP 10 - Adjusting the vertical motion and tilt Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before adjusting. This product should move smoothly and easily through the full range of motion and stay where you set it.