Yamaha DTX532K Assembly Manual

DTX532K/DTX562K
This manual describes the standard assembly procedure for the DTX532K and DTX562K electronic drum kits. It covers assembly and wiring of the kit as
shown below. When you have completed all of the steps described, you will be ready to turn on the drum module and start playing.
Example of standard assembly
Cymbal pad
Tom pads
Real Hi-hat Pad
Drum module
Hi-hat stand
Snare pad
Safety Precautions
The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating
the severity and immediacy of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The
instructions displayed together with these precautions are extremely important in terms of ensuring safety, and therefore, they should be fully observed.
* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.
* Be sure to also read the Assembly Manuals and/or Owner's Manuals that came with your pads and rack.
Failure to observe the precautions described below can result in
WARNING
serious injury or even death.
• Young children using this electronic drum kit should be supervised by a guardian to eliminate any
possibility of injury.
• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should
take special care whenever handling these components.
• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-
fore, you should take special care whenever handling these components.
• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In
addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads
may fall off or the rack may collapse or fall over, possibly causing injury.
• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe
surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.
• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If
someone were to trip on a cable, the kit could topple over and cause injury.
• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to
observe this precaution can result in injury or malfunction.
• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing
injury.
* Yamaha Corporation reserves the right to change or modify products or specifications at any time without prior notice.
U.R.G., Digital Musical Instruments Division
EN
Assembly Manual
IMPORTANT
This manual describes the process of assembling a drum-pad set and
Cymbal pad drum module to an already assembled RS502 Electronic Drum Rack.
Before starting the steps below, therefore, be sure to assemble your
RS502 as described in the Owner's Manual that came with it.
NOTICE
Before starting assembly, lay a drum mat (sold separately) on the floor.
Tom pad
Alternatively, you can place cardboard from the drum kit packaging or
the like on the floor to prevent it from being scratched. This is particu-
larly important when using the HS650A Hi-hat Stand and KP65 Kick
Pad.
Electronic drum
Kick pad rack
Please read carefully before proceeding.
Failure to observe the precautions described below can result in
CAUTION
injury and/or property damage.
• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during
this operation.
• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by
sharp tips if these components are not handled carefully.
• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.
• Do not use the electronic drum kit's rack to hold acoustic drums. Doing so could cause clamps to
break and the drums to fall off, which in turn could lead to injury.
NOTICE: Usage Precautions
• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In
addition, avoid placing heavy items on top of cables and do not allow them to touch sharp edges.
Failure to avoid these precautions can lead to cable breakage and disconnection.
• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe
this precaution can result in malfunction.
• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close
proximity to a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or out-
doors in wet weather). Failure to observe this precaution can lead to warping, discoloration, mal-
function, or breakdown.
• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these sub-
stances can cause warping and discoloration. Instead, we recommend you remove dust using a soft
dry cloth or wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first
wipe the dirt away using a cloth moistened with a neutral detergent solution and tightly wrung. Fol-
lowing this, wipe away the detergent solution using a cloth soaked in water and tightly wrung.
Open the boxes to reveal their contents.
1
© 2013 Yamaha Corporation
After opening up the packages containing your electronic drum kit, please verify that all of the following components are present.
211POAP*.*-01A0
Printed in Vietnam
ZE16340
Components of both DTX532K & DTX562K
 XP80 Snare Pad  PCY135 Cymbal
(x1) Pad (x2)
 HS650A Hi-hat  KP65 Kick Pad (x1)
Stand (x1)
 Stopper for
PCY135
pads (x2)
 Felt pad for
PCY135 pad (x2)
Components of DTX532K only
 TP70 Tom Pad (x3)  Clamp bolt
(for XP80; x1)
Assemble the RS502 Electronic Drum Rack.
2
For instructions on how to assemble the RS502 Electronic Drum Rack, refer to the Owner's Manual that came with it.
Assemble the pads and the drum module to the electronic drum rack.
3
Assembling the snare and tom pads
Tom pads
DTX532K: TP70
DTX562K: XP70
XP80 Snare Pad
 Snare pad
1.
Attach a clamp bolt to the snare pad and provision-
ally tighten (by five or six turns).
Clamp bolt (tighten in the di-
rection of the arrow)
Underside of snare pad
 RHH135 Real  Stand base for  Hi-hat clutch for  RS502 Electronic Drum Rack (x1)
 RS502 Owner's Manual (x1)
Hi-Hat Pad (x1) RHH135 (x1) RHH135 (x1)
 Nine-channel snake cable (x1)
 DTX502 Drum
 Cable band  Cable band for  Tuning key
(x6) RHH135 (x1) (x1)
 DTX532K/DTX562K Assembly Manual (this booklet; x1)
 Module holder (x1)
 PCY100/135/155 Owner's Manual (x1)
 RHH135 Owner's Manual (x1)
 XP70/80 Owner's Manual (x1)
 KP65 Owner's Manual (x1)
Components of DTX562K only
 Wing bolt  XP70 Tom Pad (x3)
(for TP70; x3)
 TP70 Owner's Manual (x1)
2.
Push the snare pad onto the rack's snare holder.
Ensure that the snare holder's rod is fully inserted
into the snare pad's mounting hole, and then tighten
the clamp bolt to secure the pad in place.
Snare pad
Rod
Snare holder
Push
on
Clamp bolt
3.
Loosen bolts A to D as shown below to adjust the
height and angle of the snare pad's playing surface.
When correctly positioned, be sure to securely re-
tighten the bolts before proceeding to the next step.
Bolt B
Bolt D
Bolt C
Bolt A
 Power adaptor (x1)
Module (x1)
* May not be included
depending on your
particular area. Please
check with your Yamaha
dealer.
 Module holder
screw (x2)
 DTX502 Owner's Manual (x1)
 Clamp bolt
(for XP70 or XP80; x4)
 Tom pads
1.
As with the snare pad, attach a wing bolt (DTX532K)
or clamp bolt (DTX562K) to each of the three tom
pads and provisionally tighten (by five or six turns).
2.
Push each of the tom pads onto one of the rack's
tom holders. Each time, ensure that the tom holder's
rod is fully inserted into the tom pad's mounting
hole, and then tighten the bolt to secure the pad in
place.
DTX532K DTX562K
Tom pad: TP70 Rod Tom pad: XP70 Rod
Push Push
on on
Wing bolt Tom holder Clamp bolt Tom holder
3.
Loosen bolts A to C as shown below to adjust the
height and angle of each tom pad's playing surface.
When correctly positioned, be sure to securely re-
tighten the bolts before proceeding to the next step.
Bolt B
Bolt A
Bolt C * DTX562K shown.
Continued on rear.