Table of Contents
Advertisement
Quick Links
©2008 Pella Corporation
INSTALLATION INSTRUCTION – INSTRUCCIONES DE INSTALACIÓN
FOR CLAD HINGED PATIO DOOR
PUERTA DE BISAGRA PARA PATIO
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
Corner
Flashing
Tape
Side
Flashing
Tape
Always read the Pella
products. By installing this product, you are acknowledging that this Limited
Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance
instructions may void your Pella product warranty. See Limited Warranty for complete details at
http://warranty.pella.com.
Installation Instructions for Typical Wood Frame Construction.
These instructions were developed and tested for use with typical wood frame wall construction
in a wall system designed to manage water. These instructions are not to be used with any other
construction method. Installation instructions for use with other construction methods, multiple
units or bow and bay windows, may be obtained from Pella Corporation or a local Pella retailer,
or by visiting http://www.pella.com. Building designs, construction methods, building materials,
and site conditions unique to your project may require an installation method different from
these instructions and additional care. Determining the appropriate installation method is the
responsibility of you, your architect, or construction professional.
Fin
Corner
Top
Flashing
Tape
Corner
Flashing
Tape
Optional
Nailing Fin
Side
Flashing
Tape
®
Limited Warranty before purchasing or installing Pella
Door Top
Door Bottom
Part Number: 801V0101
Nailing Fin
Water
Resistive
Barrier
Sheathing
Framing
Sill Flashing Tape #1
Sill Support
Sill Flashing Tape #2
Advertisement
Table of Contents
Related Manuals for Pella 801V0101
Summary of Contents for Pella 801V0101
- Page 1 By installing this product, you are acknowledging that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product warranty. See Limited Warranty for complete details at http://warranty.pella.com.
-
Page 2: Rough Opening Preparation
- DO NOT use high pressure or latex foams • Drill • Pella aluminum sill support or 2 x 4 wood blocking • Screwdrivers • Interior trim and/or jamb extensions (15 to 40 ft.) (#2 Phillips & small flat blade) -
Page 3: Setting And Fastening The Door
E. Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer 1 " than the opening width. Apply at the bottom of the opening as shown (1E) so it overhangs 1" to the exterior. 6 " Note: The tape is cut 12" longer than the width so that it will extend 6"... - Page 4 E. Plumb and square door. Place shims at each hinge and lock strike location between the door and the sides of the opening. E x t e r i o r Insert shims in other locations as needed starting up 6" from the bottom of the door to square it in the opening.
-
Page 5: Integrating The Door To The Water Resistive Barrier
INTEGRATING THE DOOR TO THE WATER RESISTIVE BARRIER Note: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant line will cover the exterior edge of the tape. -
Page 6: Interior Seal
INTERIOR SEAL Caution: Ensure use of low pressure polyurethane window and door insulating foams and strictly follow the foam I n t e r i o r manufacturer’s recommendations for application. Use of high pressure foams or improper application of the foam may cause the door frame to bow and hinder operation. - Page 7 180 grit or finer sandpaper. DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS. Remove sanding dust. Pella products must be finished per the below instructions; failure to follow these instructions voids the Limited Warranty. • On casement and awnings, it is optional to paint, stain or finish the vertical and horizontal sash edges.
-
Page 8: Exterior Finish
The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the responsibility of Pella.