Universal Remote Control CLIKR-5 UR5U-8780L Operating Instructions

Operating Instructions For 1 1 Introduction 4 4 Button Functions
The CLIKR TM -5 UR5U-8780L & UR5U-8790L is
CLIKR -5
TM
designed to operate the CISCO / SA, Pioneer,
Pace Micro, Samsung and Motorola digital
set tops, Plus the majority of TV, VCR, DVD
Cable Remote Control and AUX equipment on the market as
shown below.
CBL : Cable Set-top Box TV : Televisions
UR5U-8780L & UR5U-8790L VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Equipment, Media PC, etc.
2 2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5 5 Programming the Remote Control
3 3 Operations
IMPORTANT SETUP NOTE!
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, VCR,
DEFAULT STATE:
DVD or AUX button, depending on what device you are programming the remote to operate.
Device Default: Cable Set-Top Box (STB) There are three ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Pre-Programmed 3-Digit Code Method
through the CABLE STB. You have the option of
* The Auto-Search Method
controlling your CABLE channel and numbers
The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit code.
through the TV or VCR. Refer to section H for
This is the quickest way to set up devices made by popular manufacturers.
programming steps.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit code
Volume Default: Volume and Mute control are
numbers that correspond with the components manufacturer/brand. Code tables for this method are on the
automatically transferred to the respective
backside of the operating instructions.
Component based on the Device selected:
The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you to
CBL:TV ; TV:TV ; VCR:TV. DVD:TV ; AUX:AUX.
identify the correct code.
You have the option of controlling CABLE
Universal Remote Control, Inc.
IMPORTANT SETUP NOTE!
Volume and Mute through the TV, VCR or
www.universalremote.com This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
AUX. Refer to section G for programming
OCE-0060K Rev 07 (08/17/11) not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
steps.
A. Quick Set-Up Method C. Auto-Search Method E. Programming the AUX Device
STEP1 Turn on the equipment you want to If none of the three digit code numbers You can take advantage of the AUX function to
program. To program your TV, turn on assigned to your brand of equipment works, or
program a devices such as a media PC, gam-
the code table does not list your brand, you can
the TV.
ing console or satellite radio receiver. Follow
use the Auto Search Method to find the correct
the instruction in section B to program an AUX
STEP2 Point the remote at the component and
three-digit code number for your equipment by
device. You can also program the AUX button
press and hold the [DEVICE] key for 4
following steps:
seconds until the Device LED blinks off for a second TV, VCR or DVD player. To do this
STEP1 Turn on the equipment that you want
follow the instructions below.
and turns back on. Continue holding
the remote control to operate (Cable
the [DEVICE] key and press the number
STEP1
Turn on the 5th device you want to
Box, TV, VCR, DVD, etc.).
keys, one at a time, starting with 1, then
program (TV, VCR, DVD, etc.).
STEP2
Press the [DEVICE] button and the
2, 3...0. Stop pressing the number keys
STEP2
Press the [AUX] button and the
[OK/SEL] button simultaneously for
when the device turns off.
[OK/SEL] button simultaneously for 3
three seconds. The device LED will
STEP3 Release the [DEVICE] key to save the
seconds. The [AUX] device LED will
turn on indicating that it is ready to be
code. The Device LED will blink twice
programmed. The LED will remain on turn on for 30 seconds.
to confirm the code is stored.
for 30 seconds. The next step must be
STEP3 Press the [Device] button For the type of
Repeat the steps above for all components
entered while the LED is on.
device you want to setup. Point the
(CBL, TV, VCR, DVD, AUX).
STEP3 Press the [CH ] or [CH ] button one
remote control toward the device and
at a time or keep it pressed. The
enter the 3-digit code number assigned
B. Pre-Programmed 3-Dight Code Method
remote will emit a series of Power
to your brand.
ON/OFF code signals. Release the
STEP1 Turn on the equipment that you want
*Note : To program a second TV press TV, etc.
[CH ] or [CH ] button as soon as the
the remote control to operate (Cable
equipment turns off. STEP4 When the equipment turns off verify
Box, TV, VCR, DVD, etc.).
that you have selected the correct
*Note : You can verify that you have selected the
STEP2
Press the [DEVICE] button and the
correct code by pressing the [POWER] code by pressing the [POWER] button.
[OK/SEL] button simultaneously for
button. The equipment should turn back The equipment should turn back on.
three seconds. The corresponding
on. Then try all of the functions on the Then try all of the functions on the
device LED will turn on indicating that
remote control (i.e. volume, mute, etc.) to
remote control (i.e. volume, mute, etc.)
it is ready to be programmed. The LED
ensure you have the correct code. If any of
to ensure you have the correct code.
will remain on for 30 seconds. The
the functions do not operate as they should,
If any of the functions do not operate
next step must be entered while the
repeat the instructions from STEP3 above
as they should, enter the next 3-digit
LED is on.
to continue the Auto Search Method.
code number from the brand list.
STEP3
Point the remote control toward the
STEP4 Press the same [DEVICE] button to
STEP5 Once you have found the correct
equipment and enter the three-digit
store the code. The Device LED will
3-digit code, save it by pressing the
code number assigned to your brand
blink twice to confirm that the code
from the code tables. If there are more [AUX] button one more time. The [AUX]
has been stored.
LED light will blink twice to confirm the
than one three-digit number listed for
code was stored.
your brand, try one code number at a
D. To Identify the 3-Digit Code
time until your equipment turns off.
Programmed for a Device
F. Programming the System On/Off Button
*Note : You can verify that you have selected the
STEP1 Press the appropriate [DEVICE] button
correct code by pressing the [POWER] This allows you to program the System On/Off
and the [OK/SEL] button simultaneously
button. The equipment should turn back button so it can send up to five power On/Off
for three seconds. The device LED will
on. Then try all of the functions on the
commands with one button press.
turn on for 30 seconds. The next step
remote control (i.e. volume, mute, etc.) to
STEP1 Press the [CBL] button.
must be performed while the LED is on.
ensure you have the correct code. If any
STEP2 Press the [INFO] button. The device LED STEP2
Press the [SYSTEM ON/OFF] button
of the functions do not operate as they
will blink a number of times indicating and the [OK/SEL] button simultaneously
should, repeat the instructions from
the number of each digit for the code.
for 3 seconds. The [CBL] button will turn
STEP 3 above using the next three digit
Each digit is separated by a one second
code number from the brand list. on for 30 seconds.
interval of the LED being off.
STEP3 Press the first [DEVICE] button you want
STEP4 Store the three-digit code by pressing
Example : One blink, (pause) three blinks,
to store in the [SYSTEM ON/OFF] button
the same [DEVICE] button once
(pause) eight blinks indicates the
and then press [POWER]. Repeat this for
again. The device LED will blink twice
code number 138.
the other components you want to turn
to confirm that the code has been
*Note : Ten blinks indicates the number 0.
on/off with the [SYSTEM ON/OFF] button.
stored.
STEP4 Press the [CH ] button to save the I. Programming a 'Macro' button.
6 6 Quick Set-up Code Tables
power commands you stored. The
If your remote model has custom-programmable
CBL
[CBL] button will blink twice to confirm
Macro buttons available(See Section 4), they
the commands have been saved. Quick Number
can be programmed to act as a 'Macro' or
1
Favorite Channel button in CABLE mode. This
G. Programming Volume Control
allows you to program up to five 2-digit channels,
2
four 3-digit channels or three 4-digit channels
Volume and Mute control are factory programmed
that can be accessed with one button press.
to automatically transfer to the respective Device
TV
STEP1 Press the [CBL] button to select the CBL
mode You select, as follows:
Quick Number
mode.
CBL : TV T V : TV VCR : TV
0
STEP2 Press the [MACRO] button and
DVD : TV AUX : AUX 1
[OK/SEL] button simultaneously for 3 2
If you wish to store the CBL volume control in
3
seconds. The [CBL] button will turn
CBL mode, use the following steps.
4
on for 30 seconds.
5
STEP1 Press the [OK/SEL] button and [CBL]
STEP3 Enter the the 2, 3 or 4-digit code for the
6
button simultaneously for three
channel you want programmed first (for
7
seconds. The device LED will turn on
8
example, 007) using the Number Pad,
for 30 seconds. The next step must 9
then press the [STOP] button. Then
be performed while the LED is on.
enter the code for the next channel (for
VCR
STEP2 Press the [VOL ] button. The device example, 050), then press the [STOP]
Quick Number
button. Repeat this process for the third
LED will blink.
0
channel. The [CBL] button will blink
STEP3
Press [CBL] button. The device LED will
1
once for each channel entered.
blink twice to confirm the programming.
2
STEP4
Press the [CH ] button to store the
3
*Note : To return CBL device to TV volume
channels that were selected. The 4
repeat steps above replacing [CBL]
5
[CBL] button will blink twice to confirm
with [TV] in Step 3. 6
the storage of commands.
7
To access the programmed channels, press
H. Programming Channel Control 8
the [MACRO] button once. This will bring up 9
You can program the channel controls (Channel
the first channel. Press once again and it will
Up, Channel Down, Last and Numbers) from DVD
bring up the second channel. Press again and
one Device to operate in another Device mode.
it will bring up the third channel. Quick Number
Default channel control settings on the remote
0
J. Low Battery Warning
control are as follows: 1
2
CBL : CBL T V : CBL VCR : CBL When the batteries are low and need to be
3
DVD : DVD AUX : AUX replaced with fresh batteries, the Device LED
4
lights will blink 2 times in sequence whenever a
5
If you wish to store the TV channel controls in
[POWER] button is pressed to turn on equipment. 6
TV mode, use the following steps.
7
STEP1 Press the [OK/SEL] button and [TV] button K. Memory Lock System 8
9
simultaneously for three seconds. The
This remote control is designed to retain pro-
device LED will turn on for 30 seconds.
grammed memory for 10 years even after bat- AUX
The next step must be performed while
teries are removed from the remote control.
Quick Number
the LED is on.
0
STEP2 L. Record Your Component Set-up Codes
Press the [VOL ] button. The device
1
2
LED will blink.
TV Set-up Code Number:
3
STEP3 Press [TV] button. The device LED will
VCR Set-up Code Number:
4
blink twice to confirm the programming.
5
DVD Set-up Code Number:
6
*Note : To return TV device to CBL channel
AUX Set-up Code Number:
7
repeat steps above replacing [TV] with
8
For additional information about your remote
[CBL] in Step 3.
9
control, go to www.universalremote.com
TV
7 7 Set-up Code Tables
Manufacturer/Brand Set-Up Code Number
CBL-CABLE Converters
DWIN 257
DYNASTY 043
Manufacturer/Brand Manufacturer/Brand Set-Up Code Number
DYNEX 400
SCIENTIFIC ATLANTA/CISCO, PACE MOTOROLA 002 111 148 EIKI 187
PACE 001 005 002 ELECTROBAND 001
SAMSUNG
PIONEER 001 103 034 051 063 076 105 ELECTROGRAPH 466
MOTOROLA
SAMSUNG 001 030 ELECTROHOME 143 024 076 196
SCIENTIFIC ATLANTA/CISCO 001 003 041 042 045 046 ELEKTRA 072
ELEMENT 363 494 526 622
TV EMERSON 028 048 043 155 005 116 363 047 050 051 076 096
Manufacturer/Brand 143 153 154 052 514
Manufacturer/Brand Set-Up Code Number
ENVISION 116
SANYO
EPSON 324 590
A MARK 112 143
ESA 323
SONY
ABEX 025
FISHER 007 057
SAMSUNG
ACCURIAN 036
FUJITSU 246 198 410
LG ADMIRAL 072 251 333
FUNAI 028 043 052
ADVENT 247 388
TOSHIBA FUSION 642
ADVENTURA 002
FUTURETECH 043
PANASONIC
AIKO 103
GATEWAY 242 268
PHILIPS AKAI 116 146 248 404 405 473 475 323 387 391 615
GE 073 116 008 009 034 056 074 155 333 363
ALBATRON 017
HITACHI GEM 391
ALERON 028
SHARP GIBRALTER 116 073
AMERICA ACTION 043
GO VIDEO 026
VIZIO
AMPRO 073
GOLDSTAR 113 116 102 363 106 112 127 143
AMSTRAD 052
GRUNPY 028 043
ANAM 043 054 056 080 112
HAIER 363 501 623
AOC 116 363 112 058 616
HALL MARK 363
APEX 572
Manufacturer/Brand HANNSPREE 349 381
APEX DIGITAL 006
HARLEY DAVIDSON 028
MITSUBISHI AQUAVISION 573 574
HARVARD 043
ASTAR 477
HP HAVERMY 081
AUDIOVOX 076 454 388
HELLO KITTY 076
PHILIPS
AVENTURA 052
HIMITSU 043
JVC AVIELO 627 628
HISENSE 419 442 619 630 631
SAMSUNG AVION 441
HITACHI 011 166 009 010 012 023 075 143 158 072 363 250
AXION 039 587 613
PANASONIC
BELCOR 116
HP 378 316 327 421
PHILIPS MAGNAVOX
BELL&HOWELL 333 072
HUMAX 518
TOSHIBA BENQ 423 600
HYPERION 609
BOXLIGHT 266 HYUNDAI 337 338
PIONEER
BRADFORD 043
ILO 472 399
LG
BROCKWOOD 116
INFINITY 164
BROKSONIC 238 INFOCUS 333 230 547 548 470 532 564 595
BYDESIGN 031 032
INITIAL 035 282
CANDLE 116 002 003 363
INSIGNIA 350 400 052 164 403 454 457 604 617
Manufacturer/Brand CAPEHART 058
INTEQ 073
CARY AUDIO DESIGN 266 JANEIL 002
HITACHI
CELEBRITY 001
JBL 164
SONY CENTURION 116
JCB 001
CETRONIC 043 JCPENNEY 024 116 008 009 030 065 258 143 333 363
PHILIPS
CHANGHONG 247
JENSEN 013
SAMSUNG
CITIZEN 116 002 003 363 043 258 103 143
JVC 038 034 001 083 199 210 533 581 639 406
PHILIPS MAGNAVOX CLARION 043
KAWASHO 116 001
PANASONIC CLASSIC 043 KEC 043
CLP CLASSIC 333
KENWOOD 116 001
LG
COBY 640 641
KLEGG 466
JVC
COLORTYME 116 KLOSS 002 059
CONCERTO 363
DENON KMC 143
CONCIERGE 073
KNOLL SYSTEMS 230
PIONEER
CONTEC 043 050 051
KONKA 457
CORNEA 116 KREISEN 530
CORONADO 143
KTV 043 116 143 154
CRAIG 043 054
KURAZAI 072
Manufacturer/Brand
CROSLEY 164 LG 363 113 116 102 106 112 127 143 569 284
CROWN 043 143
LITEON 268
BOSE
CURTIS MATHES 116 258 363 143
LODGENET 072
HP
CXC 043
LOEWE 164
APPLE / iPod
CYBERHOME 015 LOGIK 072
DAEWOO 363 016 043 044 076 103 114 125 127 143
APPLE / iPod LUXMAN 363
DAYTRON 363 143
LXI 166 007 138 052 251 333 164
MICROSOFT / XBOX
DELL 320 164 363 618 MAGNAVOX 164 059 116 003 060 061 363 127 022 333 094 226
SONY / PS2 DIGITAL PROJECTION 570
390 467 431
DIMENSIA 333
LUTRON MAJESTIC 333 072
DREAMVISION 235 MARANTZ 116 164 281 562 584
X-10
DUKANE 011 025 MATSUI 164
ZINWELL
DUMONT 116 073
MATSUSHITA 080
MICROSOFT / XBOX DURABRAND 096 052 MAXENT 242