Identification and Parts Description................07-08-09 Indexing Operation........................10 Removing Drive/Live Centres....................11 Changing the Belt Speed......................12 Maintenance........................... 13 AW1416VS Parts Breakdown....................14-15 AW1416VS Parts List......................16-17-18 AW1416VS Wiring Diagram....................... 18 Declaration of Conformity... Copied from CE Certificate The undersigned, Calvin Chou authorised by The Kingcraft Machinery Company Limited No.
24 Index Pin with Magnetic Base 2 off Steel Hooks & (4) Phillips Screws 1 off Instruction Manual 1 off Guarantee Card Having unpacked your new AW1416VS woodturning lathe please dispose of the unwanted packaging responsibly. The cardboard packaging is biodegradable.
Optional Accessories... A X M I N S T E R W H I T E 1 off Extension Bed (Order No: 951249) 2 off M8 x 30mm Caphead Bolts & M8 Spring/washer General Instructions for 230V Machines... Good Working Practices/Safety The following suggestions will enable you to observe good working practices, keep yourself and fellow workers safe and maintain your tools and equipment in good working order.
General Instructions for 230V Machines... A X M I N S T E R W H I T E Keep the work area as uncluttered as is practical, this includes personnel as well as material. Under no circumstances should CHILDREN be allowed in work areas. It is good practice to leave the machine unplugged until work is about to commence, also make sure to unplug the machine when it is not in use, or unattended.
Specification... A X M I N S T E R W H I T E Axminster No. AW1416VS Rating: Trade Power: 230V 50Hz 560W Speed: 0-800,200-1,750, 400-3,600rpm Spindle Taper: Spindle Thread: M33 x 3.5mm (Ref T38) Taper Tailstock Distance Between Centres:...
Page 7
Assembly Instructions... A X M I N S T E R W H I T E Assembling the Power Cable Hooks Locate the two steel hooks & phillips screws (G) & screw them with the hooks facing inwards, into the pre-drilled holes in the lathe bed.
Page 8
(DO NOT OVERTIGHTEN). (See figs 8 & 9) Replace the carrying handle (E) & screws to the end of the extention bed (H). AW1416VS Lathe Extention Bed Illustration & Parts Description...
Page 9
Illustration & Parts Description... A X M I N S T E R W H I T E Tailstock barrel lock Access panel Access panel lock Live centre Drive centre Tailstock lock Power cable hooks Lathe bed Headstock Motor wheel Headstock Electronic inverter Tailstock wheel...
Page 10
The display provides the parameter display and shows operation status of the AC drive. The keypad provides programming interface between the user and the AC drive. For more information see manufacturer’s manual. Note: The inverter comes preset from the factory and you should not need to make any adjustments. www.axminster.co.uk...
Indexing Operation... A X M I N S T E R W H I T E The indexing facility is useful for fluted columns, clock faces and accurate hole positioning. The indexing pulley has 24 positions (15˚) indexing using the supplied index pin (F). 1-24 index Headstock Access panel...
Removing Drive/Live Centres... A X M I N S T E R W H I T E To remove the Drive Centre, locate (A) the push rod (C), while holding the tool insert the push rod (C) through the centre hole of the headstock wheel and push the drive centre out. (See figs 16,17,18) Repeat the procedure for the Live Centre in the tailstock.
Changing the Belt Speed... A X M I N S T E R W H I T E Fig 20 Fig 21 Loosen the access panel caphead screw (B) Lower the access door to give access using a Hex key. to the spindle pulley Fig 22 Fig 23...
Note: If the lathe is not going to be used for a period of time, smear a light coat of wax over the bed and place a dust sheet (Order no. 600410), over the lathe. Wax Points Motor air vent www.axminster.co.uk...