Vivotek FE8171V Quick Installation Manual

Network camera
Hide thumbs Also See for FE8171V:

Advertisement

Quick Links

FE8171V
3MP‧360° Panoramic View‧Vandal-proof

Advertisement

Table of Contents
loading

Summary of Contents for Vivotek FE8171V

  • Page 1 FE8171V 3MP‧360° Panoramic View‧Vandal-proof...
  • Page 2 Warning Before Installation Power off the Network Camera Refer to your user's manual as soon as smoke or unusual for the operating temperature. odors are detected. Contact your distributor in the event of occurrence. Do not touch the Network Do not place the Network Camera on unsteady surfaces.
  • Page 3: Package Contents

    Package Contents FE8171V Mounting Plate / Screwdriver Alignment Stickers Screws / Moisture Absorber / Double-sided Tape / Rubber Seal Plug / Rubber Washer For Mounting Plate For Camera Base Quick Installation Guide / Software CD Warranty Card Power & I/O Cables...
  • Page 4: Physical Description

    Physical Description Inner View Contacts for Internal Microphone Lens Pin Header (J7) Spring Contacts Align (B) to (A) when attaching the dome cover Pin Header (J6) Ethernet 10/100 RJ45 Socket MicroSD/SDHC/SDXC Card Slot Reset Button EN - 3...
  • Page 5 Outer View IP66-rated Vandal-proof Dome Cover Built-in Microphone Network Camera Model No: FE8171V IMPORTANT! MAC: 0002D1XXXXXX Record the MAC address under the camera base before This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:...
  • Page 6: Hardware Installation

    Hardware Installation First, use the supplied screwdriver to loose the four screws and detach the dome cover from the camera base. Then, follow the steps below to install the camera to either a ceiling or a wall. Tamper-proof Screw Rubber Stopper on the hole for Power &...
  • Page 7: Connecting Rj45 Ethernet Cable

    Connecting RJ45 Ethernet Cable RJ45 Cable Dimension (unit: mm) Recommended cable gauge: 24AWG (0.51 mm) Assembling Steps Rubber Seal 1. Drill a hole on the rubber seal plug and Plug insert an Ethernet cable through the open- ing. 2. Strip part of the sheath from the Ethernet cable.
  • Page 8 Ceiling/Wall Mount without Mounting Plate (Choose this mounting type if you would like to feed the cables form the bottom of the camera) 1. Attach the supplied alignment sticker for camera base to the ceiling/wall. 2. Using the three circles on the sticker, drill three pilot holes into the ceiling. Then hammer the three supplied plastic anchors into the holes.
  • Page 9 Ceiling/Wall Mount with Mounting Plate (Choose this mounting type if you would like to feed the cables form the side) 1. Attach the supplied alignment sticker for the supplied mounting plate to the ceiling/wall. 2. Using the three circles on the sticker, drill three holes into the ceiling. Then hammer the three supplied plastic anchors into the holes.
  • Page 10: Network Deployment

    Network Deployment General Connection (without PoE) 1. Connect RJ45 Ethernet cable to a switch. Use a Category 5 Cross Cable when your network camera is directly connected to PC. 2. Connect the power cable from the Network Camera to a power outlet. 3.
  • Page 11 Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Eth- ernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE...
  • Page 12: Assigning An Ip Address

    “Next” button to continue the program. Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up. Double-click on the MAC address that matches the one printed on the camera label or the serial number on the package box label to open a browser management session with the Network Camera.
  • Page 13: Ready To Use

    Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.

Table of Contents