Tascam Digital Portastudio DP-03 Owner's Manual page 24

3 – Names and Functions of Parts
INPUT B switch
6
Set this according to the signal source input through
the INPUT B — MIC B connector or LINE B jack on
the rear panel. Set it to MIC/LINE when connecting
a microphone or line level signal. Set it to INTERNAL
MIC B when using built-in MIC B.
BOUNCE button
7
Press this button to switch between
and modes.
BOUNCE
MIXDOWN/MASTERING button
8
Press this button to switch between
and
MIXDOWN MASTERING
In mode, press this button to switch
•
MULTITRACK
to mode.
MIXDOWN
In mode, press this button to switch to
•
MIXDOWN
mode if there is a stereo master track
MASTERING
or to return to
MULTITRACK
In mode, press this button to return
•
MASTERING
to mode.
MULTITRACK
NOTE
A pop-up appears when the mode changes.
REVERB button
9
Press to open the
REVERB SETTING
you can adjust reverb parameters. (See "Reverb" on
page 53.)
PHONES LEVEL knob
0
Use this to adjust the headphones output volume.
EQ button
q
Press to open the
EQ SETTING
you can adjust track EQ parameters. (See "Track EQ
(equalizer)" on page 53.)
After opening the
EQ SETTING
button, press F1 (INPUT) to open the
screen where you can adjust input EQ parameters. (See
"Using input EQ" on page 39.)
EQ HIGH/EQ LOW knobs
w
Use EQ HIGH knob to adjust high-frequency gain on
EQ setting screens, including the
and
INPUT EQ MASTERING EQ
Use EQ LOW knob to adjust the low-frequency gain
on EQ setting screens, including the
and
INPUT EQ MASTERING EQ
Display
e
This shows various types of operation information.
Function buttons
r
The functions of these buttons depend on the screen
currently displayed. The current function assignments
are shown at the bottom of the screen.
NOTE
For convenience, the four function buttons are referred to
in order from the left as F1, F2, F3 and F4 in this manual.
24
TASCAM DP-03
MULTITRACK
,
MULTITRACK
modes.
mode if not.
screen where
screen where
screen with this
INPUT EQ
,
EQ SETTING
screens.
,
EQ SETTING
screens.
REVERB knobs (TRACK 1–TRACK 8)
t
Use to adjust the level (volume) sent to the reverb
effect of the track's playback signal or the input signal
assigned to that track.
PAN knobs (TRACK 1–TRACK 8)
y
Use to adjust the stereo position of the track's playback
signal or the input signal assigned to that track. (See
"Stereo position (panning)" on page 53.)
REC buttons/indicators (TRACK 1–TRACK 8)
u
Use to arm a track for recording (turn recording
ON/OFF). To monitor a track's input sound through
headphones or a monitoring system, press that track's
REC button. When the track is armed for recording
(REC button ON), the REC indicator blinks when the
unit is stopped and lights when recording.
On the
INPUT ASSIGN
to change the assignment.s
On the screen, press these buttons to
TRACK MUTE
mute and unmute the tracks.
Press these buttons when the
open to select tracks.
Track faders (TRACK 1–TRACK 8)
i
Use to adjust the monitoring level of the track's
playback signal or the input signal assigned to the
track. (See "Levels and balance" on page 53.)
CD button
o
Press this to open the
CD MENU
MENU button
p
Press this to open the
MENU
HOME button
a
Press this to open the Home Screen.
When the unit is stopped and the Home Screen is
open, use this button to move between the time
counter divisions. (See "Direct locate function" on page
44.)
DATA wheel
s
Use this to change parameter values and select items
when using menus.
METRONOME button
d
Press this to open the
METRONOME
"Metronome" on page 59.)
TUNER button
f
Press this to open the
TUNER
page 59.)
MIC A
g
This built-in omnidirectional microphone becomes the
input source for INPUT A when set to INTERNAL MIC
A.
When using the tuner, use this built-in microphone to
input the sound of the instrument being tuned.
MASTER fader
h
Use to adjust the stereo signal level output from the
LINE OUT jacks and PHONES jack. Use also to adjust
screen, press these buttons
screen is
TRACK EQ
screen.
screen.
screen. (See
screen. (See "Tuner" on