Talon AC3102-55SC User Manual

Talon AC3102-55SC User Manual

Advertisement

USER MANUAL
Petrol Chain Saws
SAFETY OPERATION MAINTENANCE
43Þ
CKA
This product has been tested at a computed kickback angle (CKA) of no greater than 43 degrees.
WARNING • PLEASE READ
Beware of kickback. Hold chain saw firmly with both hands during use. For your own safety, please
read and follow the safety precautions in this manual before attempting to operate your chain saw.
Improper use can cause serious injury.
MODEL NO. AC3102-55SC/AC310220S
9096-31B203
WARRANTY INFORMATION
C H A I N
S A W
The benefits conferred by this warranty are in addition to all other conditions and warranties in respect of
this product which the consumer may have taken under the Trade Practices Act 1974 or by any legislation
of a State or Territory of Australia. This product is warranted by Talon Tools Australia (ABN 12 099 520
939)(the "Company") to be free from defects in material and workmanship for a period of 24 months from
the date of original purchase. The Company during the period of the warranty, will at its option, and sub-
ject to the conditions stated herein, repair or replace without charge this product or any component part,
which upon examination by an Authorised Service Agent or by the Company is found to be defective.
W a r r a n t y c o n d i t i o n s
This warranty will not apply:
(i) where this product has been subjected to misuse, abuse, accident or want of care;
(ii) where this product has been used for a purpose for which it was not designed or is not suited;
(iii) where the service of this product has been undertaken by a person not authorised by the Company
to carry out such work or where parts that have not been approved by the Company have been used;
(iv) where this product has been used for industrial purposes.
Should service become necessary during the warranty period, the purchaser should contact an Authorised
Service Agent or the Company. In order to obtain warranty service, the purchaser must present the store
receipt showing the name of the retailer and the date of purchase together with a completed Warranty
Card. The period of the warranty begins from the original date of purchase, notwithstanding any subse-
quent repair or parts replacement. No additional warranty or guarantee other than set out in this document,
whether written or verbal, is authorised to be made on the Company's behalf. The purchaser shall be
responsible for delivery or causing the product to be delivered to the Company or the Authorised Service
Agent and the purchaser shall be responsible for all charges in connection with re-delivery of the product
and/or the delivery of parts. Damage in transit is not covered by this warranty and purchasers should
remove from the product any liquids (if applicable) before sending and pack the product securely to pre-
vent damage.
W a r r a n t y e x c l u s i o n s
Normal wear parts or components are subject to seperate terms as follows: Normal wear parts, compo-
nents or service required when performing normal and regular maintenance of this product are not covered
by warranty unless it is found to be defective by an Authorised Service Agent or by the Company. Normal
wear parts include, but are not limited to:
Chains.
Chain Bar.
Spark Plugs.
Returns based on the above listed normal wear parts will not be accepted under this warranty as they
are considered consumable items and are at the expense of the purchaser.
W A R R A N T Y
Carburetor Adjustments.
Filters.
Lubricants.
Engine Tune-ups.
1
AU

Advertisement

Table of Contents
loading

Summary of Contents for Talon AC3102-55SC

  • Page 1 Trade Practices Act 1974 or by any legislation of a State or Territory of Australia. This product is warranted by Talon Tools Australia (ABN 12 099 520 939)(the “Company”) to be free from defects in material and workmanship for a period of 24 months from USER MANUAL the date of original purchase.
  • Page 2: Troubleshooting The Engine

    TROUBLESHOOTING GENERAL SAFETY RULES The following basic trouble shooting checks can be easily carried out to determine whether or not the unit is running Meaning of symbols marked on the product properly. If the unit will not operate after these checks then the product should be taken to an authorised service agent for further inspection.
  • Page 3: Specifications

    Model No........
  • Page 4: Assembly

    ASSEMBLY INSTRUCTIONS If saw chain is TOO LOOSE or TOO TIGHT, the sprock- To Test CHAIN BRAKE: et, bar, chain, and crankshaft bearings will wear more rap- The Chain Brake is DISENGAGED (chain can move) • TOOLS FOR ASSEMBLY idly. Study Fig. 4A for information concerning correct cold when BRAKE LEVER IS PULLED BACK AND You will need these tools to assemble your chain saw: tension (A), correct warm tension (B), and as a guide for...
  • Page 5: Operating

    • FUEL MIXING TABLE Activate throttle latch: depress throttle latch (A), then TEST CHAIN BRAKE AS FOLLOWS: squeeze throttle trigger (B), release trigger and then Place saw on a clear, firm, flat surface. GASOLINE 25:1 Ratio Lubricant the latch (Fig. 7E). Start engine.
  • Page 6: Maintenance Instructions

    WARNING: Never walk in front of a tree that VERTICAL CUTTING: • FUEL FILTER • BUCKING has been notched. Bucking is cutting a fallen log into lengths. Make sure you Hold the saw firmly with both hands and keep the CAUTION: Never operate your saw without a Make the felling cut (D) from the other side of...
  • Page 7: Bar / Chain Maintenance

    • SPARK PLUG BAR / CHAIN MAINTENANCE CHAIN LUBRICATION: Always make sure the automatic oiler system is working NOTE: For efficient operation of saw engine, spark plug • GUIDE BAR MAINTENANCE properly. Keep the oil tank filled with Talon Chain, Bar and must be kept clean and properly gapped.

This manual is also suitable for:

Ac310220sAc310220s

Table of Contents