Ford 1999 Ranger Owner's Manual

Ford 1999 Ranger Owner's Manual

Ford motor company 1999 ford ranger owner's guide
Table of Contents

Advertisement

Before driving
Starting and driving
Servicing
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright
1998 Ford Motor Company
Contents
2
4
16
71
97
103
133
152
200
209
210
1

Advertisement

Table of Contents
loading

Summary of Contents for Ford 1999 Ranger

  • Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright 1998 Ford Motor Company...
  • Page 2: Introduction

    Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
  • Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully.
  • Page 4: Instrumentation

    Instrumentation Headlamp control (pg. 16) Instrument panel dimmer switch (pg. 17) Turn signal and wiper/washer control (pg. 62) Instrument cluster (pg. 6) CHECK ENGINE Speed control* (pg. 56) 60 70 0 0 0 0 0 0 0 0 0 km/h R N D 2 1 Driver side air (pg.
  • Page 5 Electronic sound system (pg. 24) PUSH TONE TONE VOL PASSENGER AIRBAG Passenger air bag deactivate switch (pg. 86) Instrumentation Auxiliary power point (pg. 23) SEEK TUNE Climate control systems (pg. 17) * if equipped...
  • Page 6: Warning Lights And Chimes

    Instrumentation WARNING LIGHTS AND CHIMES Standard instrument cluster CHECK ENGINE <FUEL DOOR BRAKE Optional instrument cluster CHECK GAGE CHECK ENGINE FUEL RESET Check engine Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II).
  • Page 7 The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
  • Page 8 Instrumentation Fuel reset (if equipped) Illuminates when the ignition key is turned to the ON position and the FUEL fuel pump shut-off switch has been RESET triggered. For more information, refer to Fuel pump shut-off switch in the Roadside emergencies chapter. Air bag readiness Momentarily illuminates when the ignition is turned ON.
  • Page 9 Instrumentation Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released.
  • Page 10 Instrumentation O/D off (if equipped) Illuminates when the transmission control switch has been pushed. When the light is on, the transmission does not shift into overdrive. If the light does not come on when the transmission control switch is depressed or if the light flashes when you are driving, have your vehicle serviced.
  • Page 11 Speed control This light comes on when either the SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position. Safety belt warning chime Chimes to remind you to fasten your safety belts.
  • Page 12: Fuel Gauge

    Instrumentation Optional instrument cluster gauges CHECK GAGE CHECK ENGINE FUEL RESET Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion. The ignition should be in the OFF position while the vehicle is being refueled.
  • Page 13 Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
  • Page 14: Trip Odometer

    Instrumentation Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. 60 70 0 0 0 0 0 0 0 0 0 km/h 60 70 0 0 0...
  • Page 15 Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “H” and “L”). If the gauge indicates low pressure, stop the vehicle as soon as safely possible and switch off the engine immediately.
  • Page 16: Controls And Features

    Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) Turn on the low-beam headlamps and press the foglamp control to activate the foglamps.
  • Page 17 Controls and features Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. •...
  • Page 18 Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside of the vehicle. •...
  • Page 19 • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). • When placing objects on top of your instrument panel, be careful to not place them over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield.
  • Page 20 Controls and features Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except . However, the air conditioning will only function if the outside temperature is about 10°C (50°F) or above. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you...
  • Page 21 • (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
  • Page 22 Controls and features • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
  • Page 23 Controls and features AUXILIARY POWER POINT SEEK TUNE AM-FM The auxiliary power point is located on the instrument panel. This outlet should be used in place of the cigarette lighter for optional electrical accessories. PASSENGER AIR BAG ON/OFF SWITCH This switch must be used to deactivate the passenger air bag whenever a child seat is used in the right front or center front passenger...
  • Page 24 Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo PUSH Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. TONE TONE VOL SEEK TUNE AM/FM PUSH PUSH...
  • Page 25 If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode.
  • Page 26 Controls and features Radio station memory preset The radio is equipped with four station memory preset controls. These controls can be used to select up to four preset AM stations and eight FM stations (four in FM1 and four in FM2). Setting memory preset stations 1.
  • Page 27 Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. With the electronic stereo radio, press the TONE control three times, then use the volume knob to adjust the level. Speaker fade adjust (if equipped) Speaker sound can be adjusted between the front and rear speakers.
  • Page 28 Controls and features To set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes. AM/FM stereo cassette VOL - PUSH ON SEEK TUNE BASS TREB SCAN TONE SEEK TUNE FADE SIDE SEEK TUNE...
  • Page 29 Controls and features Volume/power control Press the control to turn the audio VOL - PUSH ON system on or off. Turn the control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
  • Page 30 Controls and features Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
  • Page 31 Controls and features Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
  • Page 32 Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Tape select • To enter tape mode while in radio mode, press the TAPE AMS control.
  • Page 33 To activate the feature, momentarily depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least 4 seconds duration between programs.
  • Page 34 Controls and features The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock To set the hour, press and hold the CLK control and press: • to decrease hours and • to increase hours. To set the minute, press and hold the CLK control and press: •...
  • Page 35 AM/FM Stereo / Single CD Radio VOL - PUSH ON SEEK TUNE Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
  • Page 36 Controls and features AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play.
  • Page 37 • Press to find the next listenable station up the frequency band. Seek function in CD mode • Press to listen to the next selection. • Press to listen to the previous selection. Scan function The scan function works in radio or CD mode.
  • Page 38 Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
  • Page 39 Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select • To begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
  • Page 40 Controls and features • to decrease hours and • to increase hours. To set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes. SEEK SEEK TUNE TUNE SEEK SEEK TUNE TUNE...
  • Page 41 Premium AM/FM Stereo/Cassette/Single CD/Premium Sound VOL - PUSH ON SEEK TUNE SCAN Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control.
  • Page 42 Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes.
  • Page 43 Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs.
  • Page 44 Controls and features Seek function for CD or CD changer • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
  • Page 45 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. SIDE 1-2 COMP SHUFFLE 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
  • Page 46 Controls and features To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control then press: •...
  • Page 47 Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: •...
  • Page 48 Controls and features Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track.
  • Page 49 Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust.
  • Page 50 Controls and features To set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner.
  • Page 51 Controls and features Mute mode Press the control to mute the MUTE playing media. Press the control again to return to the playing media. CD changer (if equipped) The CD changer is located behind the driver’s seat in your vehicle. Slide the door to access the CD changer magazine.
  • Page 52 Controls and features Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward. Depending on your system, you may insert up to six or ten CDs. The magazine does not need to be full for the changer to operate.
  • Page 53 • The player’s internal temperature is above 75°C (167°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe the center out to the edge.
  • Page 54 Controls and features Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Communications (CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.9, 88.1–107.1, 107.9 MHz Not all frequencies are used in a given area.
  • Page 55 TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running.
  • Page 56 Controls and features SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
  • Page 57 To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
  • Page 58 Controls and features You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or •...
  • Page 59 Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
  • Page 60 Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light (if equipped) This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed.
  • Page 61 Controls and features When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode. TILT STEERING (IF EQUIPPED) Pull the steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position.
  • Page 62 Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
  • Page 63 One touch down • Press AUTO completely down and release quickly. The window will open fully. Depress again to stop window operation. POWER DOOR LOCKS (IF EQUIPPED) Press the top of the control to unlock all doors and the bottom to lock all doors.
  • Page 64 Controls and features CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features. These include: • utility compartment with cassette/compact disc storage • cupholders • coin holder slots • flip up armrest • removable utility bag (if equipped) Use only soft cups in the cupholder.
  • Page 65 Controls and features Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds.
  • Page 66 Controls and features Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
  • Page 67 Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following procedure: To reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) ending in ON.
  • Page 68 Controls and features SECURILOCK PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) The SecuriLock passive anti-theft system provides an advanced level of vehicle theft protection. Your vehicle’s engine can only be started with the two special SecuriLock your vehicle. Each time you start your vehicle, the SecuriLock read by the SecuriLock key identification code matches the code stored in the SecuriLock passive anti-theft system, the vehicle’s engine is allowed to start.
  • Page 69 Theft indicator The theft indicator on the instrument cluster will operate as follows: • When the ignition is OFF, the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock vehicle. • When the ignition is turned to RUN or START, the theft indicator will light for 3 seconds and then go out.
  • Page 70 Controls and features Procedure to program spare SecuriLock keys to your vehicle New SecuriLock keys must have the correct mechanical key cut for your vehicle. Conventional (non-SecuriLock ) keys cannot be programmed to your vehicle. You will need to have two previously programmed SecuriLock keys and the new unprogrammed SecuriLock key readily accessible for the...
  • Page 71: Seating And Safety Restraints

    SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
  • Page 72 Seating and safety restraints Pull lever up to adjust seatback. Using the manual lumbar support Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard and down on the seat handle.
  • Page 73 Center facing jump seat (4 door SuperCab)(if equipped) To open, pull seat assembly down, then raise seatback. To stow the seat, fold seat back down and raise seat assembly to the fully upright position. Do not install a child seat in a center facing jump seat.
  • Page 74 Seating and safety restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only.
  • Page 75 Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
  • Page 76 Seating and safety restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
  • Page 77 Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions. Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
  • Page 78 Seating and safety restraints To lower the shoulder belt height, push the button and slide the height control down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster assembly to make sure it is locked in place.
  • Page 79 Shorten and fasten the belt when not in use. Adjusting the rear center facing jump seat lap belt (if equipped) The lap belts for rear center facing jump seat occupants have automatic retractors for the belt tongue and a fixed position buckle. To fasten the belt, pull the belt all the way across your hips and insert the tongue into the buckle on your...
  • Page 80 Seating and safety restraints Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
  • Page 81 (slide bar)(if equipped), shoulder belt height adjusters (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
  • Page 82 Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag...
  • Page 83 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
  • Page 84 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
  • Page 85 The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags), • one or more impact and safing sensors, passenger air bag deactivation switch and diagnostic monitor (RCM) • a readiness light and tone •...
  • Page 86 If the light fails to illuminate when the passenger air bag ON/OFF switch is in the OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. In order to avoid inadvertent deployment of the passenger air bag, always remove the ignition key from the passenger air bag ON/OFF switch.
  • Page 87 If the light is illuminated when the passenger air bag ON/OFF switch is in the ON position and the ignition switch is in ON, have the passenger air bag ON/OFF switch serviced at your Ford or Lincoln-Mercury dealer immediately. The passenger side air bag should always be ON (the air bag OFF light...
  • Page 88 Seating and safety restraints The vast majority of drivers and passengers are much safer with an air bag than without. To do their job and reduce the risk of life threatening injuries, air bags must open with great force, and this force can pose a potentially deadly risk in some situations, particularly when a front seat occupant is not properly buckled up.
  • Page 89 3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger air bag to pose a special risk for the passenger; • makes the potential harm from the passenger air bag in a crash greater than the potential harm from turning OFF the air bag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.
  • Page 90 Seating and safety restraints • the child has a medical condition that, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: •...
  • Page 91 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child.
  • Page 92 Seating and safety restraints seat cushion. You may wish to discuss the special needs of your child with your pediatrician. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
  • Page 93 (passenger side front and outboard rear seating positions)(if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
  • Page 94 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
  • Page 95 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
  • Page 96 Do not install a child seat in a center facing jump seat. Tether anchorage hardware Tether anchorage hardware kits (part number 613D20) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision.
  • Page 97: Starting

    PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 98 Starting Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than ten minutes at high engine RPM.
  • Page 99 3. Turn the key to 4 (ON) without turning the key to 5 (START). CHECK ENGINE BRAKE CHECK GAGE CHECK ENGINE <FUEL DOOR FUEL RESET Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. •...
  • Page 100 Starting STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait ten seconds and try again.
  • Page 101 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
  • Page 102 Starting Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.
  • Page 103: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 104 Driving Using RABS • In an emergency, applying full pressure may cause the front wheels to lock. If the front brakes lock, the vehicle cannot be steered. You should apply the brakes with steadily increasing force, as if “squeezing” the brakes. If you feel the front wheels begin to lock, momentarily release the pedal and repeat the “squeeze”...
  • Page 105 With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately). Using ABS •...
  • Page 106 Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
  • Page 107 TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1.
  • Page 108 Driving Driving with a 4–speed automatic transmission (if equipped) Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift. Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone.
  • Page 109 (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate on the instrument cluster.
  • Page 110 Driving 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed.
  • Page 111 N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift...
  • Page 112 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. Transmission operates in third gear. 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
  • Page 113 5. Release the clutch slowly while pressing gradually down on the accelerator pedal. • Do not drive with your foot resting on the clutch pedal. Do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions may reduce clutch life.
  • Page 114 Driving Recommended shift speeds Upshifts when accelerating (for best fuel economy) Shift from: 1 - 2 2 - 3 3 -4 4 - 5 (Overdrive) Upshifts when cruising (recommended for best fuel economy) Shift from: 1 -2 2 - 3 3 - 4 4 - 5 (Overdrive) Shift from:...
  • Page 115 FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired. If equipped with the Electronic Shift 4WD System, and the instrument panel control is moved to 4WD Low while the vehicle is moving, the system will not engage and no damage will occur to the 4WD system.
  • Page 116 Driving Using the electronic shift 4WD system (if equipped) Positions of the electronic shift system 2WD (2WD High) – Power to rear axle only. 4X4 HIGH (4WD High) – Power delivered to front and rear axles for increased traction. 4X4 LOW (4WD Low) – Power to front and rear axles at low speeds. Shifting from 2WD (2WD high) to 4X4 HIGH (4WD high) Move the 4WD control to the 4X4 HIGH position.
  • Page 117 Driving 4. Move the 4WD control to the 4X4 LOW position. HIGH Shifting from 4X4 LOW (4WD low) to 2WD (2WD high) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission).
  • Page 118 Driving 4. Move the 4WD control to the 4X4 HIGH or 4X4 LOW position. Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
  • Page 119 Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
  • Page 120 Driving When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km/h (30 mph).
  • Page 121 DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly.
  • Page 122 Driving • GCWR (Gross Combined Weight Rating) : Maximum combined weight of towing vehicle (including passengers and cargo) and the trailer. The GCWR indicates the maximum loaded weight that the vehicle is designed to tow. • Maximum Trailer Weight Rating : Maximum weight of a trailer the vehicle is permitted to tow.
  • Page 123 Driving You may add equipment throughout your vehicle if the total weight added is equal to or less than the Total Axle Reserve Capacity (TARC) weight. You should NEVER exceed the Total Axle Reserve Capacity. Always ensure that the weight of passengers, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both Gross Vehicle Weight and Front and Rear Gross Axle Weight Rating limits.
  • Page 124 Driving Trailer towing table (4x2 manual transmission) Engine Rear Maximum axle GCWR-kg ratio (lbs.) 2.5L 3.73 2 177 (4 800) 2.5L 4.10 2 177 (4 800) 3.0L 3.73 2 721 (6 000) 0-1 234 (0-2 720) 4.0L 3.55 3 175 (7 000) 0-1 660 (0-3 660) 2.5L 3.73 2 177 (4 800) 2.5L...
  • Page 125 Trailer tow table (4x4 manual transmission) 3.0L 3.73 2 721 (6 000) 0-1 089 (0-2 400) 3.0L 4.10 2 721 (6 000) 0-1 089 (0-2 400) 4.0L 3.73 3 175 (7 000) 0-1 524 (0-3 360) 4.0L 4.10 3175 (7 000) 3.0L 3.73 2 721 (6 000) 0-1 016 (0-2 240) 3.0L...
  • Page 126 Driving Trailer towing table (4x2 automatic transmission) Engine Rear Maximum axle GCWR-kg ratio (lbs.) 2.5L 4.10 2 494 (5 500) 0-1 016 (0-2 240) Equal to frontal area 3.0L 3.73 3 401 (7 500) 0-1 814 (0-4 000) 4.0L 3.55 4 309 (9 500) 0-2 721 (0-6 000) 3.0L 3.73 3 401 (7 500) 0-1 814 (0-4 000) 4.0L...
  • Page 127 Trailer tow table (4x4 automatic transmission) Engine Rear Maximum axle GCWR-kg ratio (lbs.) 3.0L 3.73 3 401 (7 500) 0-1 751 (0-3 860) 3.0L 4.10 3 628 (8 000) 0-1 978 (0-4 360) 4.0L 3.73 4 309 (9 500) 0-2 640 (0-5 820) 4.0L 4.10 4 309 (9 500) 0-2 640 (0-5 820) 3.0L...
  • Page 128 Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches For towing trailers up to 907 kg (2 000 lb), use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure.
  • Page 129 Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Using a step bumper The optional step bumper is equipped with an integral hitch and requires only a ball with a 19 mm (3/4 inch) shank diameter.
  • Page 130 Driving Trailer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles.
  • Page 131 These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. 2WD (automatic transmissions) • Release the parking brake and place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft.
  • Page 132 Driving For automatic transmissions, maximum speed is 56 km/h (35 mph) and maximum distance is 80 km (50 miles). • If you must exceed the distance or 80 km (50 miles) and/or speed of 56 km/h (35 mph), you must remove the rear driveshaft. Mark the driveshaft and axle flanges to ensure proper position when reconnecting the driveshaft.
  • Page 133: Roadside Emergencies

    HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column.
  • Page 134 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
  • Page 135 Standard fuse amperage rating and color Fuse Mini Fuses Rating Grey Violet Pink 7.5A Brown Blue Yellow Natural Green — — — — — Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’s side door.
  • Page 136 Roadside emergencies To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 7.5A 7.5A 7.5A — 7.5A 7.5A Description Power Mirror Switch Blower Motor Relay, PAD Module, Air Bag Diagnostic Monitor Left Stop/Turn Trailer Tow Connector Left Headlamp...
  • Page 137 Fuse/Relay Fuse Amp Location Rating 7.5A 7.5A — 20A or 10A 20A: If equipped with Rear Anti-Lock Brake 7.5A 7.5A — 7.5A 7.5A Roadside emergencies Description Speed Control Servo/Amplifier Assembly, Generic Electronic Module (GEM), Shift Lock Actuator, Blend Door Actuator, A/C-Heater Assembly, Turn Signals Instrument Cluster, Daytime Running Lights (DRL), RABS Resistor...
  • Page 138 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 7.5A — — — — Power distribution box The power distribution box is located in the engine compartment near the battery. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
  • Page 139 Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. MEGAFUSE The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 50A** 40A** 50A** 20A** 50A** 10A* — 20A* 15A* — Roadside emergencies Description I/P Fuse Panel...
  • Page 140 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 10A* 30A* 30A* 20A* 15A* 15A* 30A* 15A* 30A* — — — — — — — — — — — — — — — — — — * Mini Fuses ** Maxi Fuses Description Powertrain Control Module 4 Wheel Anti-lock Brake System (4WABS)
  • Page 141 CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Temporary spare tire information Your vehicle may have a temporary or conventional spare tire.
  • Page 142 Roadside emergencies Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Jack, jack handle, wheel nut wrench Key, spare tire lock (if equipped) Removing the spare tire 1.
  • Page 143 Roadside emergencies 2. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. 3. Insert the straight end of the jack handle into the rear access hole located just above the rear bumper and below the tailgate.
  • Page 144 Roadside emergencies 4. If your vehicle is equipped with P265/75 R15 AT tires, do not stow a flat or inflated full size spare tire in the spare tire carrier. The flat full size tire should be stowed and tied down in the pickup box bed until it can be repaired.
  • Page 145 Roadside emergencies 4. Insert tapered end of the lug wrench behind hub caps and twist them off. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
  • Page 146 Roadside emergencies To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. •...
  • Page 147 Roadside emergencies Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability. Preparing your vehicle 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system.
  • Page 148 Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
  • Page 149 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
  • Page 150 Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.
  • Page 151 Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a slingbelt towing procedure. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for...
  • Page 152: Maintenance And Care

    Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
  • Page 153 • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on •...
  • Page 154 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.5L I4 engine 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Transmission fluid dipstick (automatic transmission) 4. Engine oil dipstick 5. Brake fluid reservoir 6. Clutch fluid reservoir (manual transmission) 7.
  • Page 155 Maintenance and care 3.0L V6 Vulcan engine 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil filler cap 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil dipstick 6. Brake fluid reservoir 7. Clutch fluid reservoir 8. Battery 9.
  • Page 156 Maintenance and care 4.0L OHV V6 engine 1. Windshield washer fluid reservoir 2. Engine oil filler cap 3. Transmission fluid dipstick (automatic transmission) 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Clutch fluid reservoir (manual transmission) 8.
  • Page 157 Maintenance and care ENGINE OIL Checking the engine oil Refer to the maintence guide and or maintence guide and or service guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2.
  • Page 158 Maintenance and care • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
  • Page 159 Change your engine oil and filter according to the appropriate schedule listed in the maintence guide and or service guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced.
  • Page 160 3. If necessary, add brake fluid until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic.
  • Page 161 If the fluid level drops, maintain the fluid level at the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Capacities and specifications. 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir.
  • Page 162 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
  • Page 163 If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty. If this occurs, add engine coolant to the reservoir. For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter. Automotive fluids are not interchangeable;...
  • Page 164 Before adding engine coolant, check the color of the coolant in your vehicle. For vehicles with green coolant, use Ford Premium Cooling System Fluid E2FZ-19549–AA (in Canada, Motorcraft CXC-8–B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44–A.
  • Page 165 Maintenance and care Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month.
  • Page 166 Maintenance and care 4. Check the fluid level on the dipstick. It should be between the arrows in the FULL HOT range. Do not add fluid if the level is within this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the FULL HOT range.
  • Page 167 Maintenance and care Correct fluid level The transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. However, you can check the fluid without driving if the outside temperatures are above 10°C (50°F).
  • Page 168 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
  • Page 169 Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication.
  • Page 170 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the maintenance guide and or maintenance guide and or service guide for the service interval schedules.
  • Page 171 Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
  • Page 172 Maintenance and care If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal.
  • Page 173 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.
  • Page 174 Maintenance and care Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100.
  • Page 175 SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
  • Page 176 If you do not follow these precautions, your vehicle may not drive properly and safely. Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford.
  • Page 177 Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
  • Page 178 Maintenance and care • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
  • Page 179 Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause death or permanent injury.
  • Page 180 If you must replace the fuel filler cap, replace it with a genuine Ford or Motorcraft part. The customer warranty may be void for any damage to the fuel tank or fuel system if a genuine Ford or Motorcraft fuel filler cap is not used.
  • Page 181 Maintenance and care Do not use fuel containing methanol. It can damage critical fuel systems components. Vehicles certified to meet California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California cleaner-burning, low-sulfur gasolines. If you have a California-certified vehicle and California cleaner—burning gasoline is not available when you refuel, your engine should perform adequately.
  • Page 182 Compatible” dispensing station equipment. To ensure proper operation of your FFV on fuel ethanol, refuel at stations certified by the AAMA. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
  • Page 183 Running out of fuel Avoid running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine. •...
  • Page 184 Maintenance and care The amount of Empty Reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
  • Page 185 Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. •...
  • Page 186 Maintenance and care Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried). •...
  • Page 187 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
  • Page 188 Maintenance and care Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter.
  • Page 189 Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. To remove the headlamp bulb: 1.
  • Page 190 Maintenance and care To install the new bulb: 1. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. You may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly.
  • Page 191 Maintenance and care 4. Rotate bulb socket counterclockwise about ¼ turn and remove from lamp assembly. 5. Carefully pull bulb straight out of socket and push in the new bulb. 6. Insert the bulb into the parking lamp assembly. When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly and turn to...
  • Page 192 Maintenance and care 3. Rotate bulb socket counterclockwise about ¼ turn and remove from lamp assembly. 4. Carefully pull the bulb straight out of the socket and push in the new bulb. 5. Install the bulb socket in lamp assembly by turning clockwise. 6.
  • Page 193 Maintenance and care To remove the brakelamp assembly: 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb socket from lamp assembly by rotating it 45 degrees. 3. Carefully pull bulb straight out of socket and push in the new bulb. To install the brakelamp assembly: 1.
  • Page 194 Maintenance and care Using the right bulbs Function Park/turn/side marker lamps (front) Headlamps Foglamps (if equipped) Hi-mount brakelamp Rear stop/tail lamps Rear turn lamps Rear license plate lamps Backup lamp Dome lamp Map/dome-SuperCab (if equipped) Map/dome-Regular Cab (if equipped) To replace all instrument panel lights - see your dealer. REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: •...
  • Page 195 Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent.
  • Page 196 Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up paint, repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately.
  • Page 197 Maintenance and care • 3.0L • 2.5L • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
  • Page 198 Maintenance and care Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary.
  • Page 199 Maintenance and care Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary.
  • Page 200: Capacities And Specifications

    Cylinders No. 4, 5 and 6 have a “P” suffix. If any spark plug needs to be replaced, use only spark plugs with the service part number suffix letters “PP” as shown on the engine decal. REFILL CAPACITIES Fluid Ford Part Name Engine oil Motorcraft 5W30 (includes filter...
  • Page 201 Fluid Ford Part Name Transmission Motorcraft fluid MERCON ATF Motorcraft MERCON V Engine coolant Fuel tank Transfer Case Motorcraft Fluid MERCON ATF Capacities and specifications Application 5-speed manual 4x2 vehicles with automatic and 2.5L engine 4x2 vehicles with automatic and 3.0L or 4.0L...
  • Page 202 Washer Concentrate If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your coolant is orange in color, use Ford Extended Life Engine Coolant. Refer to Adding engine coolant, in the Maintenance and Care chapter.
  • Page 203 Ford part Item name or equivalent High Brake fluid and Performance clutch fluid (if DOT 3 Motor equipped) Vehicle Brake Fluid Door weather Silicone strips Lubricant Engine coolant Ford Premium Engine Coolant (green in color) Ford Extended Life Engine Coolant (orange...
  • Page 204 (4R44E and 5R55E) Ultra-Clear Windshield Windshield washer fluid Washer Concentrate Add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. ENGINE DATA 2.5L I4 Engine engine Cubic inches Horsepower 119 @ 5000 Torque 146 lb.-ft.
  • Page 205 2.5L I4 Engine engine Spark plug 1.07-1.17 (0.042-.046 inch) Ignition EDIS system Compression 9.4:1 ratio VEHICLE DIMENSIONS Vehicle Regular Cab dimensions Short Wheel Base (SWB) mm (in) (1) Overall 4 763 (187.5) length (2) Overall 1 785 (70.3) width (3) Overall 1 575 (62.0) / height 4x2/4x4 1 655 (65.2)
  • Page 206 Capacities and specifications...
  • Page 207 Compliance Certification Label is located on the front door latch pillar on the driver’s side. Capacities and specifications MFD. BY FORD MOTOR CO. IN U.S.A. DATE: XXXXX FGAWR: XXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.
  • Page 208 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. For your protection, you will also find the vehicle identification number in the following areas: •...
  • Page 209: Reporting Safety Defects

    However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
  • Page 210: Index

    Index Air bag supplemental restraint system ...81 and child safety seats ...83 description ...82 disposal ...85 indicator light ...85 passenger air bag ...83 passenger deactivation switch ...23,86,87,88,89 Air conditioning manual heating and air conditioning system ...19,20,21 Automatic transmission driving an automatic overdrive ...108,109,110,111,112 Axle refill capacities ...200...
  • Page 211 filling your vehicle with fuel ...178,180 gauge ...12 quality ...182 running out of fuel ...183 safety information relating to automotive fuels ...178 Fuses ...134,135 Gas mileage (see Fuel economy) ...183,184,185,186 Gauges ...11,12 engine coolant temperature gauge ...13 engine oil pressure gauge ...15 GVWR (Gross Vehicle Weight Rating) calculating ...123,128,129,130...
  • Page 212 Index locking/unlocking doors ...65 replacement/additional transmitters ...67 replacing the batteries ...66 Safety belts (see Safety restraints) ...11 Safety restraints cleaning the safety belts ...81,199 extension assembly ...80 for children ...90,91 lap belt ...78,79 warning light and chime ...11,80 Seat belts (see Safety restraints) ...73,74,75,76,77 Seats ...71 child safety seats ...92...
  • Page 215: Filling Station Information

    Maintenance and care chapter. 62.4L (16.5 gallons) 75.7 (20.0 gallons) 73.8L (19.5 gallons) 4.3L (4.5 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G.
  • Page 216 Automatic transmission fluid capacity-4x4 vehicles If your engine coolant is green in color, use Ford Premium Cooling System Fluid. If your engine coolant is orange in color, use Ford Extended Life Engine Coolant. Refer to Adding engine coolant, in the Maintenance and Care chapter.

This manual is also suitable for:

Ranger 1999

Table of Contents