Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
LAN Control Utility
User Manual (for XD3500U)
Preparation/SetUp .........................................................................2
Preparation before using the network function ...........................................2
Connection ..................................................................................................3
Installation ...................................................................................................3
Setting the IP address of the projector .......................................................5
When using a DHCP server ...........................................................................................6
When not using a DHCP server .....................................................................................7
Telnet setting ...............................................................................................8
Setting the password (Password Setup) .......................................................................9
Setting the display language of ProjectorView (language) ..........................................10
Setting the LAN control (LAN-Controlled Mode) .........................................................10
Setting the PJLink™ certifi cation (PJLink certifi cation Mode) .....................................11
Save and exit ...............................................................................................................11
ProjectorView ...............................................................................12
Using the ProjectorView ............................................................................12
How to start up ............................................................................................................12
VIRTUAL REMOTE controller .......................................................................................14
E-mail notifi cation function ..........................................................................................14
Initial setting .................................................................................................................15
Support for the PJLink™ function ...............................................16
Contents
EN-1
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric XD3500U
Summary of Contents for Mitsubishi Electric XD3500U
-
Page 1: Table Of Contents
LAN Control Utility User Manual (for XD3500U) Contents Preparation/SetUp .................2 Preparation before using the network function ...........2 Connection ....................3 Installation ....................3 Setting the IP address of the projector ............5 When using a DHCP server ...................6 When not using a DHCP server ..................7 Telnet setting ....................8... -
Page 2: Preparation/Setup
Preparation/SetUp Preparation before using the network function This projector is equipped with the network function to control and monitor the projector’s operations using a Web browser and to send e-mail notifi cation. Before using the network function, perform the following three preparation steps. (1) Setup of the application software “Projector-Control Device Installer”... -
Page 3: Connection
Preparation/SetUp (continued) Connection Computer LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) To LAN terminal External HUB LAN cable (option) (100BASE-TX or 10BASE-T should be supported.) • Use a straight-through category-5 cable for LAN connection. • Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from your body, causing damage to the projector. - Page 4 Preparation/SetUp (continued) Select a folder to install the program, and click Next. Click Next. Installation starts. • The progress of the installation process is displayed as shown on the right. When the installation process is completed, click Close. How to remove Projector-Control Device Installer Select [Start] - [Control Panel] - [Add or Remove Programs] - [Projector-Control Device Installer] and click ®...
-
Page 5: Setting The Ip Address Of The Projector
Preparation/SetUp (continued) Setting the IP address of the projector Before setting the IP address, check that the projector has been LAN-networked and turn on the main power of the projector. • When using multiple projectors, connect and confi gure them one by one. If you turn on the powers of the projectors that are connected but not yet confi... -
Page 6: When Using A Dhcp Server
Preparation/SetUp (continued) When using a DHCP server Select [Obtain an IP address automatically] and click Next. Click Next. • Check that the options are marked with checkmarks as shown on the right. Keep them unchanged for normal use. Click Assign. Click Finish. -
Page 7: When Not Using A Dhcp Server
Preparation/SetUp (continued) When not using a DHCP server Select [Assign a specifi c IP address] and click Next. Enter a fi xed IP address (for example, 192.168.0.1) and click Next. (Note) Do not use 0 or 255 for the last digit of the IP address. -
Page 8: Telnet Setting
Preparation/SetUp (continued) Telnet setting Setting of password, display language, LAN control, and PJLink™ certifi cation using telnet. This section describes how to set the password, display language on the ProjectorView screen, LAN control, and PJLink™ certifi cation that are necessary for the operation state control tool (commercially available) that uses the projector operation control/monitor tool ProjectorView and the industry standard PJLink™... -
Page 9: Setting The Password (Password Setup)
Preparation/SetUp (continued) Setting the password (Password Setup) Enter “0” and press the Enter key. Input the old (current) password and press the Enter key. (Default password is admin.) • If you input a wrong password, an error message appears and the setting menu is displayed again. In this case, set the password again. -
Page 10: Setting The Display Language Of Projectorview (Language)
Preparation/SetUp (continued) Setting the display language of ProjectorView (language) Enter “1” and press the Enter key. Enter “0” for English or “1” for Japanese. Setting the LAN control (LAN-Controlled Mode) Enter “3” and press the Enter key. To enable the e-mail notifi cation function of ProjectorView, enter “1”... -
Page 11: Setting The Pjlink™ Certifi Cation (Pjlink Certifi Cation Mode)
Preparation/SetUp (continued) Setting the PJLink™ certifi cation (PJLink certifi cation Mode) Enter “5” and press the Enter key. • When you don’t use PJLink™ protocol communication, skip this item. (See page 16 for PJLink™.) To enable the PJLink™ certifi cation, enter “1” and press the Enter key. -
Page 12: Projectorview
ProjectorView Using the ProjectorView This section describes ProjectorView, a tool to control and monitor the projector’s operations by a Web browser. The major functions of ProjectorView are: • Power on/off • Input source switching • State information indication (projector’s name, temperature, lamp operation time, error/alert, etc.) •... - Page 13 ProjectorView (continued) The password input screen appears. Enter the password you set. • The default password is admin. (Note) If you input a wrong password 4 successive times, the Web browser is closed. In this case, repeat from step 1. The ProjectorView main screen appears.
-
Page 14: Virtual Remote Controller
The lamp has reached its maximum usage. Replace the lamp and reset lamp counter. See user guide for complete instructions. Projector name : abc Projector model : XD3500U Projector location : 10Factory-5F Serial number : 12345 Operating hours : 2146 hours and 43 minutes... -
Page 15: Initial Setting
ProjectorView (continued) Initial setting To load information on the projector such as model name and lamp operating time, set the projector data in advance. Click the SETUP button on the ProjectorView main screen. The Projector Setup screen appears. Enter data according to the description of each setting item. (Note) •... -
Page 16: Support For The Pjlink™ Function
INF1? Inquiry about the “MITSUBISHI” is returned. manufacturer name INF2? Inquiry about the “XD3500U” is returned. model name INF0? Inquiry about other No other information is available. No parameter is returned. information CLSS? Inquiry about the “1” is returned. - Page 17 Support for the PJLink™ function (continued) [Notes on Instant Shut Down] Instant shutdown of the projector during control using the network function may cause ProjectorView to fail to display data correctly. • The operating time and temperature may not be displayed correctly. In this case, close the browser, recognize this projector using Projector-Control Device Installer, and then start the browser again.