™ Product features may vary from the picture above. Owner’s Manual with Assembly Instructions Please read this manual and save it with your original sales receipt. For Model 74558 Tools needed for assembly: Phillips Screwdriver, Hammer, and Pliers (not included). Cap Nut Assembly Tool (included).
• Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle.
• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
Vehicle Body Cowling Seat Wheel - 4 Hubcap - 4 Cap Nut - 6 Steering Column Right Mudflap 6 Volt Battery - 2 Key Assembly Microphone Parts Diagram Radio Knob - 2 Right Hand Grip Handlebar Housing - Top Half Handlebar Housing - Bottom Half Front Fairing...
WARNING • The batteries must be handled by adults only. The batteries are heavy and contain sulfuric acid (electrolyte). Dropping the batteries could result in serious injury. • Never allow children to charge the batteries. Battery charging must be done by adults only.
Thermal Fuse Backing • Install a thermal fuse in each battery: - Peel the backing from the underside of the plastic thermal fuse casing and discard the backing. - Insert the thermal fuse, prong side down, into the battery. Make sure the prongs are fully inserted into the battery.
Round Hole Right Fender Bottom View • Position the vehicle body upside down. Note: The mudflaps are marked “R” and “L” to designate right and left. • With the “R” marking facing up, align the two round holes in the right mudflap with the pegs on the underside of the right fender.
Motor Assembly Pins Rear Axle Assembly Rear Wheel Driver • Position the vehicle body upright. • Fit and hold a rear wheel driver against the motor pins on one end of the motor assembly. • While holding the rear wheel driver in place, slide the rear axle into the hole in the opposite side of the motor assembly.
Side Shifter Handle • Press the tab under the back of the seat and lift to remove the seat. • Fit the rectangular opening in the cowling over the shifter handle. • Align the front, side and rear tabs on the cowling with the slots in the vehicle body but do not snap the tabs into the slots.
Hole Lock Nut Neck • Position the handlebar so that the side with the three holes and circular indentation faces up. • Fit the neck against the bottom of the handlebar, with the holes in the handlebar and neck aligned. •...
Handlebar Groove Steering Column • Slide the bottom half of the handlebar housing onto the end of the steering column. Make sure the rim on the bottom of the handlebar housing fits into the hole in the vehicle body. • Slide the handlebar, neck side down, onto the end of the steering column.
Screw Screw Handlebar Assembly • Fit the front fairing onto the handlebar assembly. Make sure that the screw tabs on the handlebar assembly are aligned with the screw pegs on the front fairing. • Insert four #8 x " screws through the top half of the handlebar housing and into the front fairing and tighten the screws with a Phillips screwdriver.
Label Decoration Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: • Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. •...
Important Note: Use only Power Wheels Power Wheels ® thermal fuses installed. Use of any other batteries or fuses will damage your vehicle. Make sure that you charge the batteries for at least 18 hours using the enclosed Power Wheels ®...
Battery Care and Disposal Care If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. See information below for proper disposal. If acid comes in contact with skin or eyes, flush with cool water for at least 15 minutes and call a physician.
WARNING • Adult supervision is required. Children do not have the judgement necessary to avoid many accidents. Be sure that children operating this vehicle can do so safely and that they are supervised at all times. • Never use near steps, driveways, steep inclines, roadways, alleys, swimming pool areas or other bodies of water.
As assembled, your vehicle is ready to roll in low speed (2 mph, maximum). When your child is ready to drive the vehicle in high speed (5 mph, maximum), follow the instructions to disconnect the high speed lock-out. Beginner Use - Low Speed Drive Shifter REMOVE LOCK-OUT SCREW ON SIDE...
How to Operate Your Vehicle Advanced Use - High Speed Drive Disconnecting the High Speed Lock-Out Shifter REMOVE LOCK-OUT SCREW ON SIDE OF SHIFTER FOR HIGH SPEED OPERATION Before you disconnect the high speed lock-out, make sure your child knows how to start and stop the vehicle and knows the rules for safe driving.
Problems and Solutions Guide IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a problem, please contact Power Wheels toll-free at 1-800-348-0751 between 8 AM and 5 PM (EST) Monday through Friday. Or, contact your local Power Wheels the Authorized Service Center list beginning on page 25.
Problems and Solutions Guide Problem Vehicle was running Tripped thermal fuse butsuddenly stopped Short run time (Less than Undercharged batteries 1 - 3 hours per charge) Overcharged batteries Batteries are old and will not accept full charge Wrong type or improperly installed fuse Tripped thermal fuse Vehicle runs sluggishly Undercharged batteries...
Problems and Solutions Guide Problem Problem Vehicle runs sluggishly Batteries need charging Wrong type or improperly installed fuses Batteries are old and will not accept full charge Vehicle is overloaded Driving conditions are too stressful Vehicle runs in low speed but High speed lock-out does not run in high speed not disconnected...
We are continually expanding our Authorized Service Center Network. Please check this listing for the Authorized Service Center nearest you. If there is not one in your area, please call Power Wheels ® Consumer Affairs at 1-800-348-0751. ALABAMA BIRMINGHAM - Frigid Service & Sales, 701 Graymont Ave.
INDIANAPOLIS - Sullivan Hardware Do-It Center, 7021 N. Keystone, 46220, (317) 255-9230 NEW ALBANY - Wells Hardware, Inc., 1011 Vincennes Street, 47150, (812) 944-4523 SOUTH BEND - Ray’s TV and Appliance, 60717 US 31 South, 46614, (219) 291-1630 SOUTH BEND (OSCEOLA) - AAA Appliance Service Co., 11868 Lincoln Way West, 46561, (219) 679-4981 TERRE HAUTE - Corey Electronics,1101 S.
HICKORY - First Flight Bicycles, 2435 N. Center Street, 28601, (704) 324-9350 RALEIGH - Authorized Appliance Service Center, 800 North Person Street, 27604, (919) 834-3476 STATESVILLE - First Flight Bicycles, 216 S. Center St., 28677, (704) 878-9683 WILMINGTON - American Tool & Tractor, 102 Eastwood Road, Ste.