Related Manuals for Seagate Momentus 5400.2 SATA
Summary of Contents for Seagate Momentus 5400.2 SATA
- Page 1 Product Manual Momentus 5400.2 SATA ® ST9120821SB ST9100824SB ST98823SB ST96812SB ST94813SB 100392442 Rev. B August 2007...
- Page 2 SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registered trademarks are the property of their respective owners.
-
Page 3: Table Of Contents
Seagate Technology support services ........ - Page 4 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 5 Momentus 5400.2 SATA disc drive ........
-
Page 7: Introduction
Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.2 SATA Blade Server model drives: • ST9120821SB • ST9100824SB • ST98823SB • ST96812SB • ST94813SB These drives provide the following key features: • 5,400 RPM spindle speed. -
Page 8: About The Serial Ata Interface
Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For addi- tional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification. The specification can be downloaded from http://www.serialata.org. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 9: Drive Specifications
100.5 +/- 1.6 mm (3.96 +/- 0.063 inches) Weight (typical) 100 grams (0.22 lb) Average latency (msec) 5.56 Power-on to ready (typical) 3.5 sec Standby to ready (typical) 3.0 sec Startup current, (typical, peak) +5V: 1.1A Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... - Page 10 600,000 software-controlled power on/off cycles 5°C, 10% relative humidity 20,000 hard power on/off cycles 55°C, 16% relative humidity Supports Hotplug operation per SATA II specification Yes (requires COMPRESET from host after a hotplug event) Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
-
Page 11: Formatted Capacity
16,383 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 12: Physical Organization
8 Mbytes (8,192 kbytes) Physical characteristics Drive specification Height (mm) 9.5 +/-0.2 (inches) 0.374 +/-0.0078 Width (mm) 69.85 +/-0.25 (inches) 2.75 +/-0.0098 Length (mm) 100.5 +/-1.6 (inches) 3.945 +/-0.0098 Typical weight (grams) (pounds) 0.22 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 13: Seek Time
Time to ready ° Time to ready Typical Max @ 25 Power-on to Ready (sec) Standby to Ready (sec) Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 14: Power Specifications
0.80 watts Standby 0.28 watts Sleep 0.28 watts *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 15: Deferred Spinup
This feature does not impact time-to-ready in typical desktop systems. To accommodate the deferred spinup of multiple disc drives in an enclosure, Momentus 5400.2 SATA disc drives will spin up only after power is applied to the drive and after successful PHY (Physical layer) initializa- tion. -
Page 16: Conducted Noise
30°C (86°F max) Nonoperating 40°C (104°F max) 2.10.4 Altitude Operating –304.8 m to 3,048 m (–1,000 ft to 10,000+ ft) Nonoperating –304.8 m to 12,192 m (–1,000 ft to 40,000+ ft) Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 17: Shock
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degrada- tion in performance when subsequently put into operation are specified below 5–500 Hz: 5.0 Gs (0 to peak). Max displacement may apply below 22 Hz. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 18: Acoustics
150 kHz to 80 MHz, 3 Vrms, 80% AM with EN 61000-4-6: 97 1 kHz sine Voltage dips, interrupts 0% open, 5 seconds EN 61000-4-11: 94 0% short, 5 seconds 40%, 0.10 seconds 70%, 0.01 seconds Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 19: Reliability
Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. -
Page 20: Fcc Verification
As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. -
Page 21: Environmental Protection
Lead (Pb), in electronic products effective July 2006. A number of parts and materials in Seagate products are procured from external suppliers. We rely on the rep-resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our... - Page 22 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
-
Page 23: Configuring And Mounting The Drive
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 24: Configuring The Drive
For installations which require cables, you can connect the drive as illustrated in Figure 4. SATA interface connector Power connector SATA interface cable Power cable Figure 4. Attaching SATA cabling Each cable is keyed to ensure correct orientation. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 25: Drive Mounting
0.148 ±.010 X 90 2 .152 .399 DETAIL A (PATA) 2.430 .039 B C D .016 2 .012 .370 .160 DETAIL A DETAIL A (SATA) Figure 5. Mounting dimensions—top, side and end view Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... - Page 26 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
-
Page 27: Serial Ata (Sata) Interface
Attachment” specification. Hot-Plug compatibility Momentus 5400.2 SATA drives incorporate connectors which enable you to hot plug these drives in accor- dance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification can be downloaded from http://www.serialata.org. This device requires a COMRESET from the host after a hotplug event. - Page 28 3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. 4. All used voltage pins (V ) must be terminated. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
-
Page 29: Supported Ata Commands
Read Native Max Address Extended Read Sectors Read Sectors Extended Read Sectors without Retries Read Verify Sectors Read Verify Sectors Extended Read Verify Sectors without Retries Seek Set Features Set Max Address Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... - Page 30 Check Power Mode 98h or E5h Idle 97h or E3h Idle Immediate 95h or E1h Sleep 99h or E6h Standby 96h or E2h Standby Immediate 94h or E0h ATA-standard security commands Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 31 Command name Command code (in hex) Security Set Password Security Unlock Security Erase Prepare Security Erase Unit Security Freeze Lock Security Disable Password Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
-
Page 32: Identify Device Command
ATA-reserved 0000 PIO data-transfer cycle timing mode 0200 Retired 0200 Words 54–58, 64–70 and 88 are valid 0007 Number of current logical cylinders xxxx Number of current logical heads xxxx Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... - Page 33 Command sets enable extension 4000 Ultra DMA support and current mode xx7F (see note following this table) Security erase time 0000 Enhanced security erase time 0000 Master password revision code FFFE Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 34 Ultra DMA mode 1 is currently active. Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. Ultra DMA mode 5 is currently active. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
-
Page 35: Set Features Command
Enable read look-ahead (read cache) feature (default). Report full capacity available Note. At power-on, or after a hardware or software reset, the default values of the features are as indi- cated above. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 36: S.m.a.r.t. Commands
S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x 04 (abort) is written to the Error register. Momentus 5400.2 SATA Blade Server Product Manual, Rev. B... -
Page 37: Seagate Technology Support Services
Seagate Service Centers Presales Support Our Presales Support staff can help you determine which Seagate products are best suited for your specific application or computer system, as well as product availability and compatibility. Technical Support Seagate technical support is available to assist you online at support.seagate.com... - Page 38 Seagate Customer Service Operations (CSO) representative for warranty- related issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
- Page 39 Flush Cache Extended 23 connectors 18 Formatted capacity 5 CSA C22.2 (950) 13 Formatted Gbytes 3 current 3 Freeze Lock 23 cycles 13 Cylinders 5 cylinders 3 Gbytes 5 geometry 5 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 40 10 Read Sectors without Retries 23 Mean time between failures (MTBF) 13 Read Verify Sectors 23 Microcode 23 Read Verify Sectors Extended 23 mounting 19 Read Verify Sectors without Retries 23 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 41 Write Multiple 24 Shock, nonoperating 4 Write Sectors 24 Shock, operating 4 single-track seeks 7 Sleep 8 Sleep mode 4 sound power 4 Specification summary table 3 Spindle speed 3 Spinup 8 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 42 Momentus 5400.2 SATA Blade Server Product Manual, Rev. B...
- Page 44 Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100392442, Rev. B, Printed in USA...