1. Manuals
  2. Brands
  3. Seagate Manuals
  4. Storage
  5. HAWK 4 Famil
  6. Installation manual

Seagate HAWK 4 Famil Installation Manual

Wide bus
Hide thumbs
Table of Contents

Advertisement

Quick Links

. . . . . . . . . . . . . . . . . . . . . . .
HAWK 4 Family:
. . . . . . . . . . . . . . . . . . . . . . .
(Wide Bus)
. . . . . . . . . . . . . . . . . . . . . . .
ST15230W/WD/WC
. . . . . . . . . . . . . . . . . . . . . . .
ST15230DC
. . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . .

Advertisement

Table of Contents
loading

Related Manuals for Seagate HAWK 4 Famil

Summary of Contents for Seagate HAWK 4 Famil

  • Page 1 ..... . . HAWK 4 Family: ..... . . (Wide Bus) .

  • Page 2: Table Of Contents

    Product repair and return information ..... 11 Technical support services......12 Drive specifications..........15 Initial set-up information ........18 Drive configuration ..........23 Drive installation ........... 33 © 1994 Seagate Technology, Inc. All rights reserved Publication Number: 77767477, Rev. A October 1994 ® ® Seagate...

  • Page 3: Introduction

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Introduction Before attempting any installation, please read through all applicable sections of this document, including all warnings and cautions. Warning. This equipment generates, uses and can radiate radio frequency energy and if not installed in accordance with these instruc- tions, may cause interference to radio com- munications.
  • Page 4 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ The physical design characteristics of the drive(s) described herein, serve to minimize EMI radiation when installed in an enclosure that provides reason- able shielding. As such, the drive(s) are capable of meeting the Class B limits of the FCC Rules and the Regulations of the Canadian Department of Communi- cations.

  • Page 5: Before You Begin

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Before you begin Verify that the system is switched off and discon- nected from main power before any installation is attempted. Protect yourself, the drive, and your valuable pro- grams and data by reading the following cautions and warnings.
  • Page 6 • When transporting or shipping a drive or system, please ensure that they are correctly packed in original Seagate approved (or equivalent) container and shipped via an air-ride carrier experienced in handling computer equipment. Caution. The circuit assemblies and components con-...
  • Page 7 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ To insure optimum reliable equipment op- eration, it is required that technical support personnel discharge themselves by wearing a grounding strap around the wrist and be connected to a grounding terminal while working in the vicinity of, and while handling EOS/ESD susceptible assemblies/parts.
  • Page 8 4. The power supply must satisfy the safety require- ments for SELV (Safety Extra Low Voltage) cir- cuits. 5. Service is to be provided by trained Seagate ser- vice personnel. 6. The incorporation of the disc drives listed in this...
  • Page 9 3. Die Versorgungsspannungen werden im Kapitel 1.0 (Produkt Information) gezeigt. 4. Die Versorgungsspannung muss SELV entspre- chen. 5. Alle Arbeiten dürfen nur von ausgebildetem Seagate Service-Personal durchgefürhrt werden. 6. Der Einbau des Drives muss den Anforderungen gemäss DIN VDE 0805:1993 oder EN60950: 1992 (IEC 950).

  • Page 10: Installation Overview

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Installation Overview Installation of the drive can be divided into distinct phases as outlined below. Some of these may not be applicable to your particular installation requirements. Refer to the individual drive installation sections for specific information on your drive model.
  • Page 11 If an installed drive is low-level formatted, all user data stored on the drive will be lost. Note. Seagate Technology assumes no liability for lost user data. • Partitioning and high level formatting: A drive can be sub-divided into "partitions"...

  • Page 12: Product Repair Information

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Product repair information Service requirements The special facilities required for the manufacture of these drives generally prohibit repair in the field. If problems occur during installation, please contact your supplier for assistance. Do not attempt to disassemble or repair.

  • Page 13: Shipping

    Shipping: When transporting or shipping a drive, a Seagate approved container must be used. Keep your original box. They are easily identified by the Seagate Approved Package label. Shipping a drive in a non- approved container voids the drive warranty.

  • Page 14: Technical Support Services

    . Technical support services Please contact your dealer for technical support and installation troubleshooting. Product Technical Sup- port is available for all Seagate products by calling the SeaFAX, SeaFone, SeaTDD or SeaBOARD services. These are toll calls. SeaFAX:...
  • Page 15 This service is available from 8:00 AM to 5:00 PM PST, Monday through Friday. SeaBOARD: The Seagate Technical Support Bulletin Board System (BBS) is available 24 hours a day, 7 days a week. A modem is required to access this service. Modem...
  • Page 16 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ With this service you can access: • Specifications and jumper configurations for all Seagate products. • Reprints of Seagate documentation. • A directory of information and helpful utilities that you can download to your own computer. Modem Location...

  • Page 17: Drive Specifications

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Drive specifications Product Hawk 4 family (wide) Information ST15230W ST15230WD ST15230WC ST15230DC Interface [7] SCSI-2 Fast SCSI-2 Fast Cache Type Multi-segmented, 256 Kb* Capacity MB Unformatted 5170 5170 Formatted [1] 4294 4294 Cylinders 3992...
  • Page 18 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Notes. [1] Standard units are factory formatted with 512 data bytes per sector. ST15230 OEM standard models have twelve spare sectors per cylinder and 2 cylinders at inner tracks reserved for spares. [2] Does not Include on-board controller overhead.

  • Page 19: Initial Setup Information

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Initial setup information For the initial setup connect the cables, set the SCSI bus address and enable or disable (as required by system configuration), the SCSI I/O line terminator resistors (model "W" drives only). Note whether the drive model number ends in W, WC, DC or WD.
  • Page 20 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ J1-Auxiliary Power +12V +12V ret + 5V ret + 5V 68 Pin SCSI I/O DC Power Connector Connector Figure 1. DC power connection, 68 pin SCSI I/O connector ST15230WC and ST15230DC model drives receive power from the host computer through the 80 pin combined SCSI I/O and power connector (not shown, since a separate DC power cable not required).
  • Page 21 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ If the drive LED shows no on/off activity when the host is trying to communicate with it, an incorrect bus address selection at the drive (or remote ID select location) should be suspected. On "WC and DC"...
  • Page 22 "WD" model drives on the same I/O bus. Do not mix "WC" and "DC" model drives on the same bus. Read/Write head auto-park Seagate disc drives described herein mentioned in this drive park the heads automatically at power off. This feature requires no operator intervention.
  • Page 23 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ J1-DC Power Pin 1P J1-Auxiliary Pin 1A J1 Pin 1 68 Pin SCSI I/O Connector Figure 2a. Hawk 4 family ST15230W/WD model I/O con- nection 68 pin SCSI I/O and DC power con- nector).

  • Page 24: Drive Configuration

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Drive configuration Each disc drive has option select header connectors on the back, side and front where jumper plugs are in- stalled to select the way that the drive is to be config- ured and to select its ID (0 - 15) on the I/O bus.
  • Page 25 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ ST15230WC/DC family 80 pin SCSI I/O drives On Hawk 4 family, ST15230WC/DC model drives there is no J1-auxiliary. J6 can be used to set drive ID, but the host probably does it over the 80 pin interface. J6 may be used to drive the external drive activity LED.
  • Page 26 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Pin 1 SCSI I/O Connector Drive Front SCSI I/O Figure J1-DC Power Auxiliary Connector Pin 1 Figure 3a. Drive configurator Hawk 4 family ST15230W/WD model (Wide bus)
  • Page 27 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ 68 Pin SCSI I/O J1-Auxiliary Drive Connector Pin 1 Pin 1A [2] J1-DC Power 3P 2P SCSI ID = 0 SCSI ID = 1 SCSI ID = 2 SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6...
  • Page 28 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Drive with HDA up, Pin 1 End PCB down, viewed from front Pin 1 Drive Front Ground Reserved A 2 A 1 A 0 SCSI ID = 0 SCSI ID = 1 Pin 1 SCSI ID = 2 Jumper...
  • Page 29 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Notes for Figure 3a, 3b and 3c: [1] Notes explaining the functions of the various jump- ers on jumper header connectors J2, J1-auxiliary and J6 are given below in left to right order of jumper position.
  • Page 30 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ [4] The drive time-shares the ID and LED functions of J6 and J1-auxiliary. That is, a cable may be at- tached to one of these headers to pick up the signal that lights the external LED indicator.
  • Page 31 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Jumper. Position Jumper Function Description (Applies to "W" models only) With the jumper installed, the optional on- board (non-removable) terminator circuits are enabled (connected to the I/O lines). Default is jumper installed. Terminator circuits not connected to I/O lines.
  • Page 32 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ continued from previous page Entire drive is write protected. Drive is not write protected. Default is no WP jumper installed. Parity checking and parity error reporting by the drive is enabled. Default is PE jumper installed.
  • Page 33 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ continued from previous page TP TP (Not applicable to "WC and DC" model drives) Off Off No terminator power is connected to drive terminators or SCSI bus I/O pin 26. On Off Drive supplies its own terminator power only.
  • Page 34 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ J6 and J1-Auxiliary Jumper Installation Jumper Function Description *Drive ID on SCSI Bus. The drive ID is binary coded positionwise i.e., jumper in position A is drive ID 8, in position A drive ID 4, in position A is ID 2, position A is ID 1 and no jumpers is ID 0.

  • Page 35: Drive Installation

    Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Drive installation This section describes the physical mounting of the drive in the host cabinet and the logical installation as a system member, which is called drive setup. Disc drive mounting Do not touch the connector pins or any PCB compo- nents without observing static-discharge precautions.
  • Page 36 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Notes: Mounting holes three on each side, 6-32 UNC. Max screw length into side of drive 0.15 in. (3.81 mm). Screw tightening torque 6.0 in-lb (.675 NM) max with minimum thread engagement of .12 in.
  • Page 37 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Notes: Mounting holes three on each side, 6-32 UNC. Max screw length into side of drive 0.15 in. (3.81 mm). Screw tightening torque 6.0 in-lb (.675 NM) max with minimum thread engage- ment of .12 in.
  • Page 38 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Do not power up the host system until the drive is mounted and the system cover is replaced. • Connect DC power connector to the drive. (does not apply to "WC and DC" models which have DC power lines in the 80 pin I/O connector).
  • Page 39 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ SCSI interface drives The SCSI interface handles both drive geometry and defect management internally. The "no drive installed" option is selected for systems with SCSI drives. All SCSI interface drives are low-level formatted at the factory.

  • Page 40: Publication Number: 77767477, Rev. A

    Seagate Technology, Inc. 920 Disc Drive Scotts Valley, CA. 95066-4544, USA Publication Number: 77767477, Rev. A Printed in USA...

This manual is also suitable for:

Hawk 4St15230wSt15230wdSt15230wcSt15230dc

Table of Contents