Roland Classic C-380 Owner's Manual

Classic organ
Hide thumbs Also See for Classic C-380:
Table of Contents

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for Roland Classic C-380

  • Page 3: Important Safety Instructions

    Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2010 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
  • Page 4: Using The Unit Safely

    Refer all servicing capable of producing sound levels that could cause to your retailer, the nearest Roland Service Center, or permanent hearing loss. Do not operate for a long an authorized Roland distributor, as listed on the period of time at a high volume level, or at a level that “Information”...
  • Page 5 • Before cleaning the unit, turn off the power and with your retailer, the nearest Roland Service Center, unplug the power cord from the outlet (p. 24). or an authorized Roland distributor, as listed on the “Information” page.....................................................
  • Page 6: Important Notes

    POWER switch, then unplug the the data, and Roland assumes no liability concerning such loss of power cord from the power outlet. For this reason, the outlet into data.
  • Page 7: Additional Precautions

    Technology Properties Limited (TPL). Roland has licensed this technology from the TPL Group. • Roland is a registered trademark of Roland Corporation in the United States and/or other countries. • All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
  • Page 8: Table Of Contents

    Attaching to the Main Unit (C-330 Only)......................20 Attaching to the Wall..............................20 Connecting the Satellite Speakers to the Organ....................21 Opening and Closing the Keyboard Cover (C-380 only) ...................22 Locking the Cover..............................22 Connecting the Power Cord ..............................22 Turning the Power On and Off............................24 Turning On the Power..............................24...
  • Page 9 Contents Performing ....................29 Playing Various Sounds .................................29 Selecting Stops (sounds)............................29 Selecting a Sound Variation (Voice Palette).....................30 Playing the Sounds of Another Division (Couplers)....................31 Using a Manual Coupler ............................31 Using the Melody Coupler............................32 Using the Bass Coupler ............................33 Adjusting the Volume and Reverberation........................34 Adjusting the Overall Volume ..........................34 Adjusting the Volume of the Satellite Speakers .....................34 Adjusting the Reverberation ..........................34...
  • Page 10 Contents Saving and Loading Settings on USB Memory.......... 62 Formatting USB Memory ..............................62 Saving and Loading Memory Banks ..........................62 Saving to USB Memory ............................62 Loading from USB Memory into Internal Memory ..................63 Deleting a Memory Bank from USB Memory....................63 Copying a Memory Bank...............................64 Saving and Loading Voice Setup ............................65 Saving to USB Memory ............................65 Loading a Voice Setup .............................66...
  • Page 11 Contents List of Preset Song/Demo Song ..............78 List of Voices (Stops)..................79 MAN I Division (Lower Keyboard)............................79 MAN II Division (Upper Keyboard).............................79 PEDAL Division (Pedalboard) ..............................79 USER/MIDI Voice ..................................80 Troubleshooting ..................82 Error Messages..................... 85 List of Shortcuts ................... 85 Glossary ......................
  • Page 12: Introduction

    Introduction Thank you, and congratulations on your choice of a Roland Classic Organ. The Roland C-380 and C-330 Classic Organs represent a new type of organ with numerous features, allowing you to enjoy full-fledged pipe organ sound in your home.
  • Page 13: Names Of Things And What They Do

    Names of Things and What They Do Names of Things on the C-380 Music Rest (p. 19) Tablets (p. 14) Keyboard Cover (p. 22) Power Switch (p. 24) Pistons (p. 15) Headphone Jack (p. 25) Display/Panel (p. 18, 27) Organ Bench (p. 19) USB Connector (p.
  • Page 14: Tablets And Pistons (C-380)

    Names of Things and What They Do Tablets and Pistons (C-380) Tablets Coupler Tablets These select the basic stops (sounds) of the organ. These allow a specific division to simultaneously play the sound of ➔ “Playing Various Sounds” (p. 29) another keyboard.
  • Page 15 Names of Things and What They Do Pistons Memory Bank Select [M–] Piston/[M+] Piston Use these pistons to switch memory banks when you want to use more than six combinations of sounds. [SET] Piston ➔ “Recalling a Registration from a Different Memory Bank” (p. 49) This stores a combination of sounds (registration) to a general memory piston or a division memory piston.
  • Page 16: Tablets And Pistons (C-330)

    Names of Things and What They Do Tablets and Pistons (C-330) Tablets Coupler Tablets These select the basic stops (sounds) of the organ. These allow a specific division to simultaneously play the sound of ➔ “Playing Various Sounds” (p. 29) another keyboard.
  • Page 17 Names of Things and What They Do Pistons [SET] Piston Melody Coupler [MEL] Piston This stores a combination of sounds (registration) to a general This causes the highest note played on the lower manual to be memory piston. sounded by the MAN II division (upper manual) sound. ➔...
  • Page 18: Display And Panel

    Names of Things and What They Do Display and Panel External Connectors OUTPUT L/MONO, R (Output) Jacks You can connect an external speaker system here so that the sound of the organ is played from the connected speakers (p. 74). INPUT L/MONO, R (Input) Jacks You can connect an external sound module or similar device here so that its sounds are heard from the organ’s speakers (p.
  • Page 19: Before You Start Playing

    Using the Music rest * The illustration shows the C-330, but the connections are the same Gently raise the music rest, then secure it in place as for the C-380 as well. shown in the figure. Adjusting the pedalboard adjuster.
  • Page 20: Installing The Satellite Speakers

    Do not attach the speakers to any other type of wall. * Replacement screws should only be obtained from the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page. Satellite speaker attachment locations Attach the left and right satellite speakers at the same height, centered on the organ.
  • Page 21: Connecting The Satellite Speakers To The Organ

    Right Speaker connect the satellite speakers to the organ. Attach the satellite speaker grill. For the C-380 Pass the speaker cables through the openings where the corners of the satellite speaker grill have been cut off. Connect the speaker cable connectors to the satellite Position the satellite speaker grill so that the side with the corners speaker jacks located on the back of the organ.
  • Page 22: Opening And Closing The Keyboard Cover (C-380 Only)

    To close the cover, use both hands to slide it toward yourself. Locking the Cover The C-380’s keyboard cover has a lock. Keep the included key out of the reach of children so that it will not be swallowed accidentally.
  • Page 23 Before You Start Playing For the C-330 First, make sure that the [POWER] switch is OFF. Upper position OFF Connect the supplied power cord to the AC Inlet connector, then plug the other end into an AC outlet.
  • Page 24: Turning The Power On And Off

    (stop). For the C-380 Adjust the volume to an appropriate level by moving the [Master Volume] knob. Decrease the Volume Increase the Volume Adjust the volume while you play the keyboard to produce sound.
  • Page 25: Turning Off The Power

    * Use stereo headphones. For the C-380 * Roland organs feature Phones jacks. These allow you to play without having to worry about bothering others around you, even at night. However, you should be careful that you don’t disturb your neighbors, since floors and walls can too easily transmit vibrations (especially vibrations from the pedalboard).
  • Page 26: Connecting The Usb Memory

    Note on using USB memory The USB connector located at the bottom center of the organ is a The USB connector holder of the C-380 will rotate 90 degrees to left servicing connector for purposes such as maintenance. Do not or right.
  • Page 27: About The Display

    Before You Start Playing About the Display Return to the Main Screen In order to perform an operation such as changing the organ’s settings, you’ll need to start by returning to the main screen. Contents of the Main Screen Press the [Value/Exit Menu] knob a number of times. Immediately after you turn on the power, the following “main screen”...
  • Page 28: Listening To The Demo Songs

    This Roland organ has several built-in demo songs. For more information of the built-in demo songs, refer to “List of * No data for the music that is played will be output from MIDI OUT Preset Song/Demo Song”...
  • Page 29: Performing

    Performing Playing Various Sounds Selecting Stops (sounds) By pressing the sound tablets you can play a variety of pipe organ sounds. The sounds assigned to the tablets are called “stops.” The sound tablets are organized into groups called “divisions.” These tablets are called “division tablets.” If the indicator of a division tablet is lit, you’ll be able to play the corresponding stop.
  • Page 30: Selecting A Sound Variation (Voice Palette)

    Performing Selecting a Sound Variation (Voice Palette) fig.stop-up-ver.eps Press the lower part of a tablet From the main screen, press the lower part of a division tablet. The “Voice Palette” screen will appear, showing the variation of the selected stop. fig.LCD016.eps * If the indicator blinks momentarily when you press the tablet, a variation is already selected for the stop.
  • Page 31: Playing The Sounds Of Another Division (Couplers)

    In the MAN I division, press the lower part of the division coupler [II/I] tablet. The indicator will light, and the coupler will be on. On the C-380, you can also turn on the coupler by pressing the [II/I] piston to make it light. Play the lower keyboard.
  • Page 32: Using The Melody Coupler

    Performing Using the Melody Coupler When you use the melody coupler, the highest note you finger on the lower keyboard will also be sounded by the stops selected in the MAN II division. This function allows you to simultaneously play accompaniment and solo registrations by fingering a single manual.
  • Page 33: Using The Bass Coupler

    Performing Using the Bass Coupler The bass coupler allows you to layer the sound of a PEDAL division onto the lowest note you’re fingering on the lower keyboard. Press the bass coupler [BASS] piston. When the bass coupler is on, the piston’s indicator will light. Press the piston once again to turn off the indicator.
  • Page 34: Adjusting The Volume And Reverberation

    Performing Adjusting the Volume and Reverberation You can adjust the volume or reverberation that is heard when you play the keyboards or when you play back a song from internal memory or USB memory. When you’re in the main screen, turning any of the following knobs will cause the “VOLUME” screen to appear for a while. fig.Volume-Tone.eps Volume of “Volume”...
  • Page 35: Changing The Type Of Reverberation

    Performing Changing the Type of Reverberation By applying reverberation you can obtain the acoustic characteristics of a performance in a concert hall. Changing the Room Type By changing the type of reverberation you can experience the sensation of performing in a variety of locations. From the main screen, press the [Select/Menu] knob.
  • Page 36: Changing The Wall Type

    Performing Changing the Wall Type You can make additional changes to the reverberation by changing the wall type (the material out of which the wall is constructed). From the main screen, press the [Select/Menu] knob. Turn the [Select/Menu] knob to select “4 Room Modeling.” fig.LCD005.eps Press the [Select/Menu] knob to access the “Room Modeling”...
  • Page 37: Adding Soft Vibrato (Tremulant)

    Performing Adding Soft Vibrato (Tremulant) The tremulant effect adds vibrato (cyclic modulation) to the sound. Use this when you want to add an expressive feel to a solo or small ensemble performance. This is often used on compositions of the romantic era, gospel, and music for worship services.
  • Page 38: Changing The Tuning (Temperament)

    Performing Changing the Tuning (Temperament) Historical styles of music such as baroque can be played in the tunings that were used during that time. Most works today are composed with the assumption that they will be played in equal temperament (the most common temperament used today).
  • Page 39: Using Baroque Pitch

    Performing Using historical temperaments By using a historical temperament when playing a composition suited for it, the beauty and tension of that work can be brought out even more greatly. In particular, when playing a work that uses a modulation-capable temperament and includes modulation, the sonority of the chords will change, adding subtle changes in the tonal character as the composition progresses.
  • Page 40: Tuning To Match The Pitch Of Another Instrument

    Performing Tuning to Match the Pitch of Another Instrument When playing in an ensemble with another instrument, you can adjust the organ’s reference pitch to the other instrument. The reference pitch is usually expressed as the pitch of the middle “A” note. By adjusting the “Tuning”...
  • Page 41: Transposing The Key

    Performing Transposing the Key The transpose function lets you shift the pitch in semitone steps without changing the keys you play on the keyboard. For example, if a song is written in a difficult key that contains numerous sharps ( ) or flats ( ), you could use this setting to play the song in an easier key.
  • Page 42: Using The Expression Pedal To Adjust The Volume Of The Organ

    Performing Using the Expression Pedal to Adjust the Volume of the Organ You can use the expression pedal to adjust the volume of the organ. Depressing the expression pedal will increase the volume, while releasing it will reduce the volume. fig.ex-pedal.eps Decrease the volume Increase the volume...
  • Page 43: Storing The Division For Which The Volume Is To Be Adjusted

    About the C-380’s MAN I & PEDAL enclosed piston The C-380 has a MAN I & PEDAL enclosed piston; when you press this piston to turn it on, you’ll be able to use the expression pedal to adjust the volume of the MAN I division (lower keyboard) and PEDAL division (pedalboard).
  • Page 44: Setting The Minimum Volume Of The Expression Pedal

    Performing Setting the Minimum Volume of the Expression Pedal You can adjust the minimum volume that will be in effect when the expression pedal is at the minimum position. From the main screen, press the [Select/Menu] knob. Turn the [Select/Menu] knob to select “8 Exp. Pedal.” fig.LCD009.eps Press the [Select/Menu] knob to access the “Exp.
  • Page 45: Using The Kick Switches

    It will switch to the adjacent general memory piston. Each time you press the kick switch, the general memory piston will switch to the next higher number. This has the same function as the C-380’s [PREV] piston. PREV It will switch to the adjacent general memory piston. Each time you press the kick switch, the general memory piston will switch to the next lower number.
  • Page 46: Storing A Combination Of Stops

    The MAN I division and MAN II division each have five division memory pistons, and each piston stores one registration. In the case of the C-380, a bank contains not only the five general memory pistons 1–5, but also the MAN I division’s memory pistons 1–5 and the MAN II division’s memory pistons 1–5.
  • Page 47: Storing Or Recalling A Registration

    Recalling a Registration Press one of the general memory pistons or division memory pistons (C-380 only). • If you press one of the general memory [1]–[5] pistons, the state of the stops for all divisions, the couplers, and the tremulant settings stored at that piston will be recalled.
  • Page 48: Using Memory Banks

    Storing a Combination of Stops Using Memory Banks The state of the general memory [1]–[5] pistons and the division memory [1]–[5] pistons (C-380 only) can be stored as a “memory bank.” You can use twenty memory banks (M01–M20). This allows you to store a total of one hundred registrations (5 x 20).
  • Page 49: Recalling A Registration From A Different Memory Bank

    Even if you press the [NEXT] piston after arriving at number 5 of memory bank M20, you will stay at memory bank M20 number 5. You can also assign the function of the [NEXT] piston, or the [PREV] piston (C-380 only) to a kick switch so that you can use your foot to switch between registrations (p. 45).
  • Page 50: Practicing Along With A Preset Song Or Performance Data

    Practicing Along with a Preset Song or Performance Data You can practice by playing along with preset songs (demo songs) that are built into the organ, or with performance data that you’ve recorded from your own playing (p. 56). • You can mute (silence) the performance of a specific division (p. 52). •...
  • Page 51 Practicing Along with a Preset Song or Performance Data Turn the [Value/Exit Menu] knob to select the media on which the song is stored. Setting Explanation Play back song data from USB memory Play back song data from internal memory Play back built-in preset song (demo song) * For more information about the built-in preset songs, refer to “List of Preset Song/Demo Song”...
  • Page 52: Muting A Specific Division During Playback

    Practicing Along with a Preset Song or Performance Data Muting a Specific Division During Playback When playing back a song, you can individually mute (silence) the performances of the MAN II division (upper keyboard), MAN I division (lower keyboard), and PEDAL division (pedalboard). From the main screen, press the [STOP] piston to access the “Song Recorder”...
  • Page 53: Playing Back A Specific Division As A Guide Tone

    Practicing Along with a Preset Song or Performance Data Playing Back a Specific Division as a Guide Tone From the main screen, press the [STOP] piston to access the “Song Recorder” screen. Choose the song that you want to play back (p. 50). Turn the [Select/Menu] knob to select “Division Mute.”...
  • Page 54: Changing The Tempo

    Practicing Along with a Preset Song or Performance Data Changing the Tempo From the main screen, press the [STOP] piston to access the “Song Recorder” screen. fig.LCD034.eps Turn the [Select/Menu] knob to select “Tempo.” fig.LCD038.eps Turn the [Value/Exit Menu] knob to adjust the tempo. Press the [Value/Exit Menu] knob twice to return to the main screen.
  • Page 55: Using The Metronome

    Practicing Along with a Preset Song or Performance Data Using the Metronome From the main screen, press the [STOP] piston to access the “Song Recorder” screen. fig.LCD034.eps Turn the [Select/Menu] knob to select “Metronome Volume.” fig.LCD039.eps Turn the [Value/Exit Menu] knob to adjust the value. Setting OFF, 1–10 Turn this “OFF”...
  • Page 56: Recording Your Performances

    Recording Your Performances Recording a Song fig.rec-play-2.eps From the main screen, press the [STOP] piston to access the “Song Recorder” screen. You can also acsess the ”Song Recorder” screen by Quick Menu. fig.LCD034.eps Press the [REC] piston; the [REC] piston will light. The [PLAY/PAUSE] piston will blink, and the organ will enter recording-standby mode.
  • Page 57: Play Back The Recorded Song

    Recording Your Performances Play Back the Recorded Song Press the [STOP] piston to return to the first measure of the song you recorded. Press the [PLAY/PAUSE] piston to play back the recorded song. You can adjust the tempo of the playback (p. 54). Press the [PLAY/PAUSE] piston, you can pause the playback.
  • Page 58 Recording Your Performances Turn the [Select/Menu] knob to select “No.”, and turn the [Value/Exit menu] knob to choose the save-destination number. fig.LCD042.eps Press the [SET] piston; the data will be saved. fig.LCD953.eps When saving is finished, the name of the newly saved song data will appear. Press the [Value/Exit Menu] knob twice to return to the main screen.
  • Page 59: Deleting A Recorded Song

    Recording Your Performances Deleting a Recorded Song Here’s how to delete song data that you saved to internal memory or USB memory. You can’t erase a preset song. If you want to delete a song that’s saved on USB memory, connect your USB memory to the external memory connector (p.
  • Page 60: Copying A Saved Song

    Recording Your Performances Copying a Saved Song Saved performance data can be copied in either direction between internal memory and USB memory. You can’t copy a preset song. Up to 99 songs can be saved in internal memory, and up to 999 songs can be saved in one USB memory unit. Connect your USB memory to the external memory connector (p.
  • Page 61 Recording Your Performances Never disconnect the USB memory or turn off the power before the copy has been completed. Otherwise, you risk damaging the USB memory or the organ’s internal memory, rendering it unusable. When copying is finished, the song name will change to the copy-source song name. Press the [Value/Exit Menu] knob twice to return to the main screen.
  • Page 62: Saving And Loading Settings On Usb Memory

    USB memory on the organ. * For the C-380, not only the settings of the general memory pistons * When you format USB memory, all songs or settings that have been but also the settings of the division memory pistons will be saved stored on that USB memory will be lost.
  • Page 63: Loading From Usb Memory Into Internal Memory

    Saving and Loading Settings on USB Memory Turn the [Select/Menu] knob to select the “No.” field. Turn the [Select/Menu] knob to select the “No.” field. fig.LCD623.eps Turn the [Value/Exit Menu] knob to select the area in which you want to save the settings. Press the [SET] piston to save the data.
  • Page 64: Copying A Memory Bank

    Saving and Loading Settings on USB Memory Turn the [Select/Menu] knob to select “Delete Memory Copying a Memory Bank Bank.” fig.LCD631.eps Here’s how a specific bank saved in internal memory or USB memory can be copied to another bank of the organ’s internal memory.
  • Page 65: Saving And Loading Voice Setup

    Saving and Loading Settings on USB Memory Turn the [Select/Menu] knob to select “Copy from,” and Saving and Loading Voice Setup turn the [Value/Exit Menu] knob to change to “USB.” fig.LCD641.eps A “Voice Setup” contains data that specifies the volume balance of each sound (stop), its brightness, and various adjustments for parameters.
  • Page 66: Loading A Voice Setup

    Saving and Loading Settings on USB Memory Turn the [Select/Menu] knob to select the “Name” field, Turn the [Select/Menu] knob to select “Load Voice and press the [Select/Menu] knob to assign a name to the Setup.” voice setup you want to save. fig.LCD653.eps For details on how to assign a name, refer to “If you want to name the data you’re saving”...
  • Page 67: Deleting A Voice Setup

    Saving and Loading Settings on USB Memory Press the [SET] piston to delete the voice setup. Deleting a Voice Setup A confirmation screen will appear. If you decide to cancel, press the [Value/Exit Menu] knob. If you want to deleting a voice setup from USB memory, fig.LCD959.eps connect your USB memory to the external memory connector (p.
  • Page 68: Other Settings

    Other Settings Turn the [Select/Menu] knob to move the cursor to the Settings for the USER/MIDI Couplers top position, and then turn the [Value/Exit Menu] knob to select the tablet that you want to assign a USER Voice. You can use the [USER/MIDI] couplers to play “USER/MIDI Voice” (p. fig.LCD072.eps 80) that are not included in the sound tablets, or to play sounds on an external MIDI sound module.
  • Page 69: Playing Sounds On An External Midi Sound Module (Midi Coupler)

    Other Settings Press the [Value/Exit Menu] knob twice to return to the Turn the [Select/Menu] knob to select the “Source/MIDI main screen. CH” item, and turn the [Value/Exit Menu] knob to change the MIDI transmit channel. The settings you make in the “USER/MIDI” screen are saved in the fig.LCD073.eps registration (p.
  • Page 70 Other Settings Settings for transmitted messages Indication Explanation Range Chorus Specifies the depth of chorus OFF, 1–127 Here’s how to specify the MIDI messages that will be transmitted when a [USER/MIDI] coupler is on. Velocity value KBD: From the main screen, press the [Select/Menu] knob. The keyboard’s velocity will be used Velocity EXP:...
  • Page 71: Midi Settings

    Other Settings MIDI Settings Local Control Setting (Local) When the organ is connected to a MIDI sequencer, change this Here you can make various settings for the organ’s MIDI setting to Local Off. functionality. Since the “Thru” function of most sequencers is turned on, the notes For more about MIDI, refer to “Connecting to MIDI Equipment”...
  • Page 72: Specifying The Type Of External Midi Sound Module (Tone Name)

    Factory reset will cause all of the recorded songs, the general * If you’re using a MIDI sound module that does not support GM2, memory pistons, and division memory pistons (C-380 only) to choose the “OFF” setting. return to their factory settings. Please copy your settings to USB memory before you proceed.
  • Page 73: Storing Your Settings (Customize)

    Other Settings Press the [SET] piston. Storing Your Settings (Customize) The Factory Reset will be executed. Do not turn off the power while the following screen is displayed. The following settings will return to their default state when you fig.LCD963.eps switch off the organ's power, but you can use the procedure described below to store these settings.
  • Page 74: Connecting External Devices

    Connecting External Devices Connecting to Audio Equipment Connecting to Amplified Speakers fig.ConnectAudio-2.eps By connecting to amplified speakers, you can play the organ’s sounds through the external speakers. You can also record your performance into a digital audio recorder or other recording device. * To make connections, use audio cables with phone plugs, such as the PCS-100PW (sold separately).
  • Page 75: Playing The Sounds Of An External Midi Sound Module Or An Audio Device

    Connecting External Devices Playing the Sounds of an External MIDI Adjusting the Volume of your Audio Device Sound Module or an Audio Device You can adjust the volume and reverb depth of the sound from the connected audio device or MIDI sound module. You can play the sounds of an external MIDI sound module or another audio device such as a digital audio player through the Press the [Select/Menu] knob.
  • Page 76: Connecting To Midi Equipment

    Connecting External Devices Connecting to MIDI Equipment Using the Organ to Play the Sounds of a MIDI Sound Module By connecting the organ with an external MIDI device to transfer performance data, you can use one device to play the other. You can use each division’s keyboard to play sounds on a separately For example, you can play or select sounds on the other device.
  • Page 77: Using V-Link

    Connecting External Devices Turn the [Select/Menu] knob to select “V-LINK,” and turn Using V-LINK the [Value/Exit Menu] knob to change the ON/OFF setting. When external, V-LINK-compatible, audiovisual presentation fig.LCD076.eps equipment is connected, you’ll be able to control the imagery presented by such equipment at the same time as you play the organ.
  • Page 78: List Of Preset Song/Demo Song

    List of Preset Song/Demo Song • All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws. • No data for the music that is played will be output from MIDI OUT. •...
  • Page 79: List Of Voices (Stops)

    List of Voices (Stops) MAN I Division (Lower Keyboard) Tablet (VP0) Bourdon 16’ Violone 16’ Principal 16’ Quintaton 16’ Principal 8’ Open Diapason 8’ Montre 8’ Prinzipal 8’ Gemshorn 8’ 2nd Diapason 8’ Voce umana II 8’ Aeoline 8’ Gedackt 8’...
  • Page 80: User/Midi Voice

    List of Voices (Stops) USER/MIDI Voice Sounds for user settings can be assigned to the [USER/MIDI] display name Voice name feet couplers and played together with the organ sounds of each 22 2 2/3 Quinte QUINTE 2-2/3’ division. The sounds that are available as user settings consist of “organ 23 2 2/3 Nazard NAZARD 2-2/3’...
  • Page 81 List of Voices (Stops) Orchestra display name Voice name feet 65 16+4 FlCélIV FLUTE CÉLESTES IV 16+4 66 16+4 Cél IV CÉLESTES IV 16’+4’ display name Voice name feet 67 16+8+4 CélVI CÉLESTES VI 16+8+4 90 Organ Harp ORGAN HARP 8’...
  • Page 82: Troubleshooting

    Troubleshooting If the C–330/C-380 does not function in the way you except, first check the following chart. If this does not resolve the problem, consult your dealer or a nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page.
  • Page 83 Keep the cell phone as far away from the You hear noise — C-330/C-380 when a call is made or received, or during a call. C-330/C-380 as possible, or turn it off. Something is wrong with the sound You’re playing outside the recommended range of pitches for when you play certain areas of the This is not a malfunction.
  • Page 84 Page We cannot guarantee operation if USB memory not manufactured by Roland is Can’t read or write USB memory You’re using USB memory not manufactured by Roland. — used. Use USB memory available from Roland. Sounds or settings have changed since you turned on the power.
  • Page 85: Error Messages

    After waiting several seconds, you may be able to play back the song by pressing the [PLAY/PAUSE] button again. Memory Full. The internal memory is full. The C-330/C-380 cannot deal with the excessive MIDI data sent from the external MIDI device. MIDI Buffer Full. Reduce the amount of MIDI data sent to the C-330/C-380.
  • Page 86: Glossary

    The round switches arranged below the manual keyboard are called tone will be affected, but the C-380 provides a MAN I & PEDAL pistons. enclosed piston which lets you turn on/off control of the MAN I division and PEDAL division while you play.
  • Page 87 Baroque organ to a French romantic era organ. Temperament The C-330/C-380 allows you to switch between several historical tuning methods (temperaments) in addition to the standard equal temperament of today.
  • Page 88: Midi Implementation Chart

    Active Sense Reset Able to choose between o and x. Notes SysEx used for stop and coupler changes. Only C-380 recognized 21–26. Mode 1: OMNI ON POLY Mode 2: OMNI ON, MONO o : Yes Mode 3: OMNI OFF, POLY...
  • Page 89: Specifications

    Specifications C-380 C-330 Keyboard Manual 2 x 61 keys (C2–C7, Tracker action) Pedal 30 keys (C2–F4, Parallel Concave) Stops (Tablet) Total 33 Stops MAN I: 9 Tablets + 2 (User/MIDI Couplers) MAN II: 10 Tablets + 2 (User/MIDI Couplers) Pedal: 8 Tablets + 2 (User/MIDI Couplers)
  • Page 90 Specifications C-380 C-330 Pedal Expression Pedal Kick Switch Speakers Woofer 2 x 20 cm Tweeter 2 x 5 cm Satellite Speakers 2 x 12 cm Phones jack (Stereo) Output jacks (L/Mono, R) Input jacks (L/Mono, R) MIDI connectors (In, Out)
  • Page 91: Index

    Index Adjuster Main Screen ............................................Amplified Speaker Manual Coupler ......................................Aux In Reverb Meantone ............................................ Aux In Volume Melody Coupler ........................................Memory Bank ..................... Metronome ......................MIDI CH BAROQUE ............................................MIDI Sound Module Bass Coupler ..................
  • Page 92 Index Tablet ......................... Temperament ..................... Tempo ......................– Transpose ....................... Tremulant ......................Tremulant Tablets ................... USB memory ......................USER/MIDI Coupler ............... USER/MIDI screen ................... – Vallotti ........................Variation ........................VENETIAN ....................... VERSAILLES ....................Vibrato ........................V-LINK ........................Voice Setup ......................VOICING ........................
  • Page 93 For EU Countries This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 94 For EU Countries For China...

This manual is also suitable for:

Classic c-330

Table of Contents