RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 2 General Safety Rules Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.
Page 3
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 3 Power tool use and care Use the power tool, accessories and tool bits etc., in accordance with these Do not force the power tool. Use the correct instructions and in the manner intended for power tool for your application.
Page 4
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 4 Using personal safety devices and working in Never use dull or damaged bits. Sharp bits safe environment reduces risk of injury. must be handled with care. Damaged bits can snap during use. Dull bits require more After changing the bits or making any force to push the tool, possibly causing the bit adjustments, make sure the collet nut and...
Page 5
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 5 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 6 Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Drywall Router NOTE: For tool specifications refer to nameplate on your tool.
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 7 Assembly Disconnect the plug from turning it counter-clockwise until the depth the power source before guide can slide freely on the metal housing. making any assembly, adjustments or For bits with a guide point (Drywall XBITS™, changing accessories.
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 8 Operating Instructions BUMP SWITCH (ON/OFF) This tool is switched “ON” by the bump switch located on the back of the motor housing (Fig. 5). TO TURN THE TOOL “ON” slide the switch button up or “1”...
Page 9
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 9 Step 1: Be certain that the box or fixture is Step 6: Move the bit right and upward firmly mounted and all wires or other maintaining light continuous pressure toward obstructions around the opening are pushed the box (Fig.
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 10 Maintenance Service rotating it counter-clockwise (Fig. 1). Be careful not to lose the screw. Preventive maintenance performed by unauthorized 3. Using your fingernail, pry the brush door per so n nel may result in misplacing of loose and remove it from the tool.
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 11 Cleaning not at tempt to clean by inserting pointed objects through openings. To avoid accidents always dis connect the tool from Certain cleaning agents the power supply before cleaning or and sol vents damage performing any main tenance.
Page 12
RZ 2610011339 01-10:RZ 2610011339 01-10 2/3/10 11:16 AM Page 12 ZB10 Drywall Zip Drywall Zip Bits (Ø1/4”) ® ® (available in 10-pack) WD1 / WD10 Window & Door Zip Bit with ® Guidepoint (available in 1-pack or 10-pack) Do not use WD1/WD10 bits that measure 3"...