This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered,
brush-
covered or grass-covered
land unless the enginds
exhaust system is equipped with a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required
by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark
arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department,
Page 1
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 36113! Cleveland, Ohio 44136-0019. TROY-BILT LLC.P.O.BOX 361131, CLEVELAND, OHIO 44136-0019 PRINTED IN U.S.A. FORM NO. 769-00830A...
Page 2
TABLEOFCONTENTS Content Page Content Page Important Safe Operation Practices Maintaining Your Chipper Shredder Assembling Your Chipper Shredder Trouble Shooting Illustrated Parts List Know Your Chipper Shredder Operating Your Chipper Shredder Warranty FINDINGMODELNUMBER This Operator's Manual is an important part of your new chipper shredder. It will help you assemble, prepare and maintain the unit for best performance.
Page 3
SECTION 1: IMPORTANT SAFEOPERATION P RACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Page 4
i. Never s tore themachine orfuelcontainer Never operate without the shredder hopper, inside where thereisanopenflame, s park, chipper chute, or chute deflector properly attached or pilotlight(e.g.furnace, waterheater, to the machine. Never empty or change discharge spaceheater, c lothes dryer, e tc.) bag while the engine is running.
Page 5
SAFETY LABELS FOUND ONYOURUNIT " ROTATING CUTTmNG BLADES. KEEP BANDS AND FEET OUT OF OPENRNG WHILE MACHINE IS RUNNING. DO NOT OPERATE THIS MACHINE UNLESS THE CHUTE DEFLECTOR HAS BEEN PROPERLY RNSTALLED AND RS SECURED WITH HAND KNOBS, SECTION 2: ASSEMBLING Y OUR CHIPPER SHREDDER IMPORTANT: This unit is shipped without gasoline or oil in the engine.
Page 6
Attaching TheDebrisCollection Bag Attaching TheTowBar(Model CS4210 Only) • To attach the bag, place the opening of the bag • To attach the tow bar, remove the spring pin and completely over the chute deflector. clevis pin from the end of the tongue. •...
Page 7
pper Handle_ Chipper Chute i Latch Starter Handle... --Chute Deflector -Wing Knob Two Bar -Lock (Model CS4210 Only) Figure 4 SECTION 4: OPERATING Y OUR CHIPPER SHREDDER • Open fuel shut-off valve shredder can result in foreign objects being (Model CS4210). WARNING: The operation of any chipper...
Page 8
Grasp the starter handle and pull the rope out Observe the following guidelines when shredding yard debris: slowly until resistance is felt. When it becomes slightly harder to pull the rope, slowly allow the rope • Never attempt to shred material other than normal to recoil.
Page 9
• Applyintermittent pressure ( force, i nshortpulses) whilefeeding larger (2-3-inch diameter) branches Locking Buckle intothechipper c hute, t oavoid bogging orstalling theengine. IMPORTANT: Never f eedbranches witha diameter greater t hanthree(3)inches intothechipper c hute. Doing socanresult i nserious damage toyourunit's chipper b lades, flailsorimpeller.
Page 10
ChuteDeflector: L ubricate t hepivotpoints onthe _'hute ..chutedeflector withlightoiloncea season. ---- Deflector Engine:Refer t othe Briggs & Stratton Owner/Operator Ill\ S)II Shredder manual packed with your unit for lubrication Screen instructions. Maintenance Housing Engine Refer to the Maintenance section of the Briggs & Stratton Owner/Operator manual packed with your unit.
Page 11
Chipper Blade Lock Washer & Nut Support Impeller Hex Bolts & ..Internal ..Hex Screw Saddle Washers Figure 9 Figure NOTE: Use a 3/16" hex key (Allen) wrench on the Chute Deflector outside of the blade and a 1/2" box (or socket) wrench on the inside of the impefler.
Page 12
StoringYourChipper Shredder • Clean the equipment thoroughly. • Wipe equipment with an oiled rag to prevent rust. • Refer to engine manual for correct engine storage instructions • Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer.
Page 14
Models CS4265& CS4210 t Model CS4210 Only :_ Model CS4265 Only...
Page 15
ModelsCS4265& CS4210 Ref. Ref. Part No. Part Description Part Description Part 681-04006 681-04002 Upper Chipper Chute Assembly Outer Flail Housing Assembly 681-04007 710-0157 Lower Chipper Chute Assembly Hex Cap Screw, 5/16-24 x.75 710-0106 710-0502A Hex Sems Screw, 3/8-16 x 1.25 Hex Cap Screw, 1/4-20 x 1.25 710-3013...
Page 16
Damage resulting from the shall bind Troy-Bilt. During the period of the warranty, the installation or use of any part, accessory or attachment exclusive remedy is repair or replacement of the product approved...