1. Manuals
  2. Brands
  3. Heat & Glo LifeStyle Manuals
  4. Indoor Fireplace
  5. XLR-N-AU
  6. Owner's manual

Heat & Glo LifeStyle XLR-N-AU Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model:
XLR-N-AU
XLR-PB-AU
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• DO NOT spray aerosols in the vicinity of this
appliance while it is in operation.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This is a room sealed appliance and no other ventilation is
required than what is provided.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13
Owner's Manual
Installation and Operation
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• DO NOT place articles on or against this appliance.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
This is primarily a decorative appliance and it is not certified as
a space heater.
SAI Global
Ref No GSCS20139
AS4558
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo LifeStyle XLR-N-AU

Summary of Contents for Heat & Glo LifeStyle XLR-N-AU

  • Page 1 This is primarily a decorative appliance and it is not certified as gas supplier. a space heater. This is a room sealed appliance and no other ventilation is required than what is provided. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 2 Save this manual for future reference. Heat & Glo, a brand of Hearth & Home Technologies 7571 215 Street West, Lakeville, MN 55044 Copyright 2011 • Printed in U.S.A. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 3: Congratulations

    The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace. Type of Gas SAI Global Certification Nº: DMS (mm) Model Number Serial Number xxxx-xxx Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 4: Table Of Contents

    E. Junction Cord Information ......45 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 5 E. Contact Information ......70  = Contains updated information. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 6: Limited Lifetime Warranty

    Conditions, Exclusion, and Limitations listed Igniters, Electronic Components, and Glass 2 years Factory-installed blowers Molded refractory panels 3 years Firepots and burnpots 2000-645 (1-12) Page 1 of 3 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 7 HHT (8) modifi cation of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interrup- tions or fl uctuations of electrical power supply to the appliance. 2000-645 (1-12) Page 2 of 3 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 8 444 Swan Street 277 Lord Street 10 Martin Avenue Richmond 3121 East Perth 6000 Arncliff 2205 (03) 9429-5573 (08) 9228-2600 (02) 9597-7222 2000-645 (1-12) Page 3 of 3 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 9: Listing And Code Approvals

    Columns highlighted in gray = The gas control valve supplied with this product is approved for a maximum inlet pressure of 3.40 kPa. For pressures over 3.40 kPa, an in line pressure regulator must be installed upstream from the gas control valve. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 10: User Guide

    DECORATIVE DOORS (NOT SHOWN) SECTION 2.D. FIXED GLASS ASSEMBLY (NOT SHOWN) SECTION 14.E. CLEAR SPACE SECTION 2.C. Figure 2.1 General Operating Parts Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 11: Clear Space

    This appliance ships standard without a decorative media option. For installation and removal of these decorative media options, refer to installation instructions which ship with the media options. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 12: Control Module Operation

    SWITCH FLAME HI/LOW STATUS NG/LP GAS-TYPE SWITCH SELECTOR SWITCH INDICATOR LED Figure 2.3 Control Module Note: The HI/LO and LP/NG switches on the control module are non-functional on the XLR fireplace. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 13: Lighting Instructions (Ipi)

    See installation and operating vice agency or the gas supplier. instructions accompanying appliance. For additional information on operating your Hearth & Home Technologies fireplace, please refer to www.fireplaces.com. Final inspection by Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 14: After Fireplace Is Lit

    Wall above appliance feels hot to No action necessary. This appliance ships with a non-combustible material attached. Specifica- the touch. tions of the attached non-combustible material are listed in Section 1.E. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 15: Maintenance And Service

    - Light deposits: Use a soft cloth with soap and water - Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer) • Reinstall door or decorative front. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 16: Maintenance Tasks-Qualified Service Technician

    • Gas pressure taps are accessible by removing the deco- rative front and fixed glass assembly. Refer to section 11.A for information related to the gas valve and gas pressure settings. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 17: Getting Started

    REMAINS CLEAR ON ANY MANTEL PIECE INSTALLATION OPTIONAL WALL SWITCH HEATER MUST BE INSTALLED AND FLUE PENETRATION COMPLETE PRIOR TO FINISH SHEETING GAS LINE (SECTION 11) Figure 4.1 Typical System Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 18: Design And Installation Considerations

    1/2 - 3/4 in. (13 - 19 mm) length, #6 or #8 Self-drilling screws One 1/4 in. (6 mm) female connection (for optional fan). Caulking material (149 °C (300 °F) minimum continuous exposure rating) Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 19: Framing And Clearances

    TOP VENT ONE 90° ELBOW See Section D. Inches 19-1/4 17-3/4 Figure 5.5 & 5.6 See Section D. Millimeters 1350 1220 1910 Figure 5.5 & 5.6 Figure 5.1 Appliance Locations Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 20: Constructing The Appliance Chase

    Combustible Behind Sides of Front of Opening Opening Opening Opening to Ceiling Floor Flooring Appliance Appliance Appliance (Vent Pipe) (Height) (Depth) (Width) Inches 8-3/4 Millimeters 1070 1270 Figure 5.2. Clearances to Combustibles Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 21: Mantel And Wall Projections

    (80 mm) MIN. AIR SPACE 7 in. Figure 5.6 Non-Combustible Zone (180 mm) Figure 5.4 Non-Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening) Note: AIR SPACE denoted in Figure 5.6 is defined by the nailing tabs and metal standoffs. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 22: Termination Locations

    39.8°-42.5° ............990 42.5°-45.0° ............1 220 45.0°-49.4° ............1 520 49.4°-53.1° ............1 830 53.1°-56.3° ............2 130 56.3°-59.0° ............2 290 59.0°-60.3° ............2 440 *910 mm minimum in snow regions Figure 6.1 Minimum Height From Roof To Lowest Discharge Opening Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 23 4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a flue terminal to a LP Gas cylinder. A flue terminal is considered to be a source of ignition. MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES Figure 6.3 Minimum Clearances for Termination Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 24: Vent Information And Diagrams

    A length of straight pipe is allowed between horizontal runs may be level. two 45º elbows (see Figure 7.1). Vertical 8-1/2 in. (216 mm) Horizontal Figure 7.1 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 25 10 ft. (3.05 m) 4 ft. (1.2 m) 15 ft. (4.6 m) H Max. = 15 ft. (4.6 m) V + H Max. = 40 ft. (12.2 m) Figure 7.3 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 26 4 ft. (1.2 m) 15 ft. (4.6 m) H + H Max. = 15 ft. (4.6 m) V + H + H Max. = 40 ft. (12.2 m) INSTALLED HORIZONTALLY Figure 7.4 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 27 15 ft. - 44 ft. (4.6 m - 13.4 m), an exhaust restrictor may be needed. The exhaust restrictor can be located in the appliance manual bag. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 28 + H Max. = 40 ft. (12.2 m) * No specific restrictions on this value EXCEPT V + H cannot exceed 40 ft. (12.2 m) Note: Use SLP Series components only. Figure 7.8 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 29 Max. = 40 ft. (12.2 m) * No specific restrictions on this value EXCEPT V cannot exceed 40 ft. (12.2 m) Note: Use SLP Series components only. INSTALLED HORIZONTALLY Figure 7.9 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 30 1-1/2 ft. (457 mm) 4 ft. (1.2 m) 4 ft. (1.2 m) 4 ft. (1.2 m) 3 ft. (1.0 m) components only. Maximum= 40 ft. (12.2 m) Figure 7.10 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 31: Vent Clearances And Framing

    * Shows center of vent framing hole for top venting. The center of the hole is one 10 in. (254 mm) above the center of the horizontal vent pipe. Figure 8.2 Wall Penetration Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 32: Install The Ceiling Firestop

    Figure 8.3 Installing Ceiling Firestop INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM 3 FASTENERS PER SIDE CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 8.4 Installing the Attic Shield Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 33: Install Attic Insulation Shield

    • Bend all tabs inward 90° around the top of the shield. These tabs must be used to prevent blown insulation from getting between the shield and vent pipe, and to maintain air space clearance. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 34: Appliance Preparation

    For all venting applications, ensure that the pipe gasket is in place before attaching any pipe section. This gasket is shipped in place around the starting collar. See Figure 9.2. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 35: Securing And Leveling The Appliance

    Reference the Heat-Zone®-240V Kit instructions for the remaining installation steps. REMOVE COVER PLATE ATTACH ® HEAT-ZONE -240V HERE Figure 9.4 Remove Cover Plate Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 36: Installing Vent Pipe (Slp Pipe)

    Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 37: Assemble Slip Sections

    • Only outer pipes are sealed, sealing the inner flue is not required. • All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 38: Disassemble Vent Sections

    1/8 in. (3 mm) larger than the support box outline. • Lower the support box through the hole in the roof until its bottom is at least 2 in. (51 mm) below the ceiling (Figure Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 39: Install Metal Roof Flashing

    • Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 10.12. • Caulk the overlap seam of any exposed pipe sections that are located above the roof line. Figure 10.14 Assembling the Storm Collar Around the Pipe Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 40: Install Vertical Termination Cap

    • Once the pipe section and the termination cap have been connected, slide the wall thimble up to the interior wall surface and attach with screws provided. See Figure 10.16. Figure 10.16 Wall Thimble Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 41: Install Horizontal Termination Cap

    WARNING! Risk of Fire! the termination cap must be positioned so that the arrow is pointing up. • Use a high-temperature sealant gasket to seal between the pipe and exterior firestop. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 42: Gas Information

    Columns highlighted in gray = The gas control valve supplied with this product is approved for a maximum inlet pressure of 3.40 kPa. For pressures over 3.40 kPa, an in line pressure regulator must be installed upstream from the gas control valve. Table 11.1 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 43: High Altitude Installations

    Reduce burner orifice 4% for each 1000 ft. (305 m) above fitting. See Figure 11.4. 2000 (610 m). Figure 11.3. Remove Valve Plate 4. Lift the valve assembly up and out to make necessary service or repair. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 44: Electrical Information

    FLAME IGNITER SENSE TO JUNCTION CORD GRAY MODULE RC300 4.5V DC (AA X 3) RC100 (OPTIONAL REMOTE CONTROL) JUNCTION CORD THERMOSTAT WIRE ASSEMBLY / WALL SWITCH WIRE Figure 12.1 IntelliFire Plus™ Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 45: Electrical Service And Repair

    This can be accessed by removing the valve assembly. See WARNING! Risk of Shock! Replace damaged wire with Figures 11.1 and 11.2. type 105 °C rated wire. Wire must have high temperature insulation. Figure 12.2. Junction Cord Information Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 46: Finishing

    2. Screw each nailing tab to the adjoining framing material. Ensure that the air space clearance is maintained on Figure 13.2 Front Side Finishing Detail the sides of the fireplace. See Figure 13.2. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 47 Overlap Method of finishing. Note: Finishing materials are designed to overlap the outer edges of the finishing flanges up to the fireplace opening. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 48 All joints between the factory-installed non-combustible board and 3/8 in. (10 mm) building material (dry wall, LOWER FINISH FLANGE plywood, wood composites, etc.) can be taped and sealed with combustible drywall tape. BOTTOM COVER PANEL Figure 13.6 Lower Cover Panel Positioned Correctly Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 49: Mantel And Wall Projections

    FRAMING Figure 13.7 Clearances To Combustible Mantels Or Other Combustibles Above Appliance 1-1/2 in. (37 mm) Note: For non-combustible fireplace finish material (marble, stone, etc) specifications refer to Section 13.C. 3/8 in. (10 mm) BUILDING MATERIAL Figure 13.9 Front Side Finishing Detail Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 50: Facing Material

    TONIC DECORATIVE Figure 13.12 Non-Combustible Finish Material Diagram for 0 - 1 FRONT SHOWN in. (0 - 25 mm) Thick Overlap Fit Method (Tonic or Martini Decorative Front) NON-COMBUSTIBLE FINISHING MATERIAL 0 - 1 in. (0 - 25 mm) THICK DRYWALL OR EQUIVALENT 3/8 in. (10 mm) Figure 13.11 Overlap Fit Method (Tonic or Martini Decorative Front) Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 51 (0-102 mm) 3/4 in. (19 mm) 20-1/2 in. (520 mm) APPLIANCE OPENING (HEIGHT) 3 in. (76 mm) 0-4 in. (0-102 mm) DRYWALL OR EQUIVALENT 3/8 in. (10 mm) Figure 13.13 Inside Fit Method (Tonic Decorative Front Only) Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 52: Decorative Fronts

    (1.13 m) Figure 13.15 Tonic Decorative Front 13 in. Inside dimension decorative front (height). 327 mm 19-1/2 in. Outside dimension of decorative front (height). 495 mm Overlap Fit Only See Section 13.C. MARTINI DECORATIVE FRONT (MT-SLR-**) Figure 13.16 Martini Decorative Front Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 53: Appliance Setup

    4. Put pressure on the glass as you allow the glass assem- bly to drop into the two lower tabs. See Figure 14.1. 5. Tilt top of glass towards fireplace and engage both top spring latches Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 54: Air Shutter Setting

    7/16 in. 1.1 cm 11 mm 11 mm Butane* Full Open Full Open Full Open *Butane gas is only approved for use in Europe, Australia, and New Zealand Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 55: Troubleshooting

    Verify module is securely grounded to metal chassis of appliance. d. Module voltage output / Valve/Pilot Verify battery voltage is at least 5.7 volts. Replace batteries if volt- solenoid ohms readings. age is below 5.7. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 56 Shutter Setting Check to assure correct shutter setting for your model and gas type. c. Gas Type Assure correct fuel matches unit gas model and compo- nents. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 57 At control module, turn off fireplace by sliding the ON/OFF/ Remote control or control REMOTE switch to OFF. Warning! Risk of Burns! Fireplace is module failure hot. Use caution when accessing module. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 58: Component Access

    4. Verify the replacement module is installed to the wire BURNER CLIP diagram listed in Section 12. ON/OFF/REMOTE SWITCH GAS VALVE BASE PAN Figure 16.4 Remove Burner Assembly CONTROL BATTERY MODULE DC ADAPTER PACK Figure 16.2 Valve Components Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 59: Access Through The Valve Assembly

    See Figure 16.6. VALVE ASSEMBLY GASKET Figure 16.6 Remove Valve Plate 4. Lift the valve assembly up and out to make necessary service or repair. 5. Replace gasket before reinstalling the valve assem- bly. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 60: Gas Valve Replacement

    5. Unscrew (2) screws located under the pressure taps to remove the gas valve from the valve bracket. PILOT VALVE FITTING BRACKET GAS BALL VALVE VALVE O R I F I C E FLEX FLARE FITTING Figure 16.9 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 61: Reference Materials

    LEFT VIEW FRONT VIEW RIGHT VIEW Location Inches Millimeters Location Inches Millimeters 1218 1092 37-3/4 16-1/2 13-1/4 6-1/2 39-1/2 1006 41-3/4 1060 3-1/2 6-3/4 1195 56-1/2 9-5/16 16-3/4 Figure 17.1 Appliance Dimensions Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 62: Maintenance Tasks

    2. Replace batteries in remote transmitters and battery-powered receivers. Carbon Deposition 1. Appliances incorporating a live fuel effect, and designed to operate with luminous flames, may exhibit slight carbon deposition. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 63: Vent Components Diagrams

    (352 mm) (241 mm) 14 in. (356 mm) DRC-RADIUS Cap Shield 5 in. 12 in. (127 mm) (302 mm) 14 in. (352 mm) DVP-BEK2 DVP-HPC Cap Brick Extension Figure 17.2 Vent Components Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 64 SLP36 DVP-HSM-B SLP-PIPE SLP48 1219 Extended Heat Shield SLP6A 2 - 6 51 - 152 SLP12A 2 - 12 51 - 305 SLP-FS SLP-WS SLP-HVS Ceiling Firestop Wall Shield Firestop Horizontal Pipe Support Figure 17.5 SLP Series Vent Components Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 65 Snorkel Termination Cap Support Box-Black Termination Cap SLP-DCF-BK SLP-WT-BK SL-2DVP Ceiling Firestop Wall Thimble-Black Adapter Black 12 in. (305 mm) 7 in. (178 mm) 15-1/2 in. (394 mm) DVP-FBHT SLP90 SL-2DVP DVP-FBHT Figure 17.6 SLP Series Vent Components Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 66 8-3/8 in. (140 mm) (146 mm to 213 mm) (213 mm) 3° 87° 15 in. 10-1/2 in. (381 mm) (267 mm) 11 in. (276 mm) SLP-HRC-SS SLP-HRC-ZC-SS HORIZONTAL TERMINATION CAP Figure 17.7 SLP Series Vent Components Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 67 Burner P & B 2198-007 Base Pan 2198-115 Glass Door Assembly GLA-SLR Thermostat Wire 2118-170 Junction Cord Assembly 2222-374 Additional service part numbers appear on following page. 1/13 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 68 Power Supply 2166-305 12.13 Bracket 2143-143 Orifi ce N (#42C) 582-842 Orifi ce B (#55C) 582-855 Orifi ce P (.057C) 582-057 Additional service part numbers appear on following page. Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...
  • Page 69 P2B-XLR-AU Conversion Kit P N2PB-XLR-AU Pilot Orifi ce N 593-528 Pilot Orifi ce B 593-529 Pilot Orifi ce P 593-527 Regulator N NGK-DXF-NP Regulator P & B LPK-DXF-NP Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

  • Page 70: Contact Information

    5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending. 2000-945B Printed in U.S.A. - Copyright 2013 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev. o • 1/13...

This manual is also suitable for:

Xlr-pb-au

Table of Contents