Page 1
Quick Response Swing with Remote Control Model Number: B0323, B3002 Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. Tools needed for assembly: Phillips Screwdriver and Scissors (both not included). Requires four “D” (LR20) alkaline batteries for swinging and sound operation;...
Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.
Page 3
Parts 2 Front Legs (Longer) Motor Housing Front Base Seat with Restraint 2 Seat Wire Caps Seat Wire 3.5mm x 1.25cm Screw - 4 Shown Actual Size Remote Control and Holder Housing 2 Rear Legs (Shorter) Rear Base Bracket 2 Seat Tubes M4 Screw - 4 M4 Bolt - 1 Shown Actual Size...
Page 4
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts. Front Legs...
Page 5
Assembly Holder • Position the holder so that the hole in the holder aligns with the hole in the front leg. • Insert the M4 bolt through the holder, front leg and into the lock nut. • Tighten the bolt with a Phillips screwdriver. Do not over-tighten.
Page 6
Assembly Pull Rear • Pull both rear legs out until they “snap” into place. Press Button Front Rear Base Base • Place the rear base on a flat surface so that the buttons face the front base. • While pressing the buttons on each side of the rear base, fit the rear legs onto the rear base.
Page 7
Assembly M4 Lock Nut Rounded Side Shown Actual Size Seat Lock Nut Tubes Hexagonal Opening • Position the bracket so that the tall end is toward the bottom edge of the seat. Hint: The M4 lock nuts have been assembled to the bracket at the factory.
Page 8
Assembly Slots • Lift the seat tubes slightly. • With the seat wire hanging down, insert the ends of the seat wire through the slots in the seat, as shown. Rounded Edge Up Seat Wire Cap Hole Seat Wire Ends of Seat Wire Seat Wire •...
Page 9
Assembly Frame Hub Push Button Swing Tube Front of Seat Curved Front Base • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs.
Page 10
Assembly Elastic Loop • Fit the bottom edge of the pad around the bottom edge of the seat. • Hook the elastic loops on each side of the pad to the peg on the back of the accessory bins. 3.5mm x 1.25cm Screw - 4 Shown Actual Size Elastic Loop...
Battery Installation Hint: We recommend using alkaline batteries for longer battery life. Compartment Swing • Locate the battery compartment door on the swing frame. • Insert a coin into the battery compartment door and pry the battery compartment door off of the swing frame. •...
Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
Adjusting the Seat Upright Recline Adjust the seat angle in any of three positions: Upright, Semi-Recline or Recline. To adjust the seat angle: • Push down on the seat back to position the seat wire in the desired groove in the bracket for Upright, Semi-Recline or Recline.
Page 14
Swinging IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs less than 24 lbs., but is really active and appears to be able to climb out of the swing, immediately discontinue its use. • Slide the power switch to on If you do not use the remote, this swing continues swinging until the power switch is turned off Power L.E.D.
Page 15
Storage Press Buttons • Fit the bottom of the remote into the cupped portion of the holder. • Push to “snap” the top of the remote under the holder clips. • Turn the toybar back to its storage position. • Press the button on the inside of each housing and push the rear legs toward the front legs.