Central Machinery 44846 Assembly And Operating Instructions Manual
Central Machinery 44846 Assembly And Operating Instructions Manual

Central Machinery 44846 Assembly And Operating Instructions Manual

34 inch floor radial drill press

Advertisement

34 inch floor radial
asseMbly and operating instructions
Visit our website at: http://www.harborfreight.com
read this material before using this product.
failure to do so can result in serious injury.
saVe this Manual.
Copyright
2000 by Harbor Freight Tools
©
tained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not
be included.
for technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10b

drill press

Model
. All rights reserved. No portion of this manual or any artwork con-
®
44846

Advertisement

Table of Contents
loading

Summary of Contents for Central Machinery 44846

  • Page 1: Drill Press

    Manual. Copyright 2000 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork con- © ®...
  • Page 2: Specifications

    When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. Rev 10b SKU 44846 Page 2...
  • Page 3 Do not use the tool if any switch does not turn On and Off properly. 17. guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures. 18. replacement parts and accessories. When servicing, use only identical SKU 44846 Page 3...
  • Page 4 Before drilling, turn on the motor and check for bit wobble or machine vibration. If this is found, correct the problem before drilling. Set the proper spindle speed for the specific drilling operation. SKU 44846 Page 4...
  • Page 5 When unpacking, check that all parts are included. Refer to the Parts Lists and Assembly Drawings located at the end of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. assembly Assembly hardware is located in one box and one bag.
  • Page 6 - Place the long side of a combination square on the Table. - Align the short side of the square to the drill bit. - If the Table is not square to the bit, loosen Hex Bolt (B12) with Hex Bolt (B12) SKU 44846 Page 6...
  • Page 7: Operation

    Pull out the Guide Pin (16) and turn it 90 degrees so that it’s cross pin rests on top of the outlet. Align the mark on the Column Guide (18) with the Scale (33). Once the Head is tilted to the desired angle, retighten the Clamping Lever. SKU 44846 Page 7...
  • Page 8 The Drill Press has five different Chuck speeds. Refer to the speed chart in the Belt Guard (A25). Lift the Belt Guard lid. Loosen the Thumb Nut (28). The belt tension should release. Move the V-belt (A1) to the desired level (speed) on the pulleys. SKU 44846 Page 8...
  • Page 9: Maintenance

    Move the Chuck to its uppermost position and lock in place. Insert a screwdriver in the lower-front notch of the Cap Spring (8). Hold it in place and, using a wrench, remove the (outer) Hex Nut (7) only. SKU 44846 Page 9...
  • Page 10: General Maintenance

    Monthly, check the tightness of all mounting screws and bolts in the Base, Column, and Head assemblies. Check belt for wear and replace if frayed or damaged in any way. Lubricate Spindle assembly with a light oil, weekly. Store in a clean and dry location. SKU 44846 Page 10...
  • Page 11: Troubleshooting

    SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 44846 Page 11...
  • Page 12: Head Assembly Parts List

    Roll Pin Moving Bar Scale Screw, Socket Hd. Head Feed Knob Feed Rod Locking Shoe Guide Pin Ring, Depth Stop Retaining Ring Column Guide Depth Lock Screw Pin Stop Horizontal Tube Cover Mount head assembly drawing SKU 44846 Page 12...
  • Page 13 Washer, Rubber Motor Pulley Quill Tube Screw, M6x10 Chuck Key Belt Guard Chuck Form Washer Arbor pulley and spindle assembly drawing When ordering a part from this drawing, add an “A” prefix to the part number. SKU 44846 Page 13...
  • Page 14 Hex Bolt, M16x35 base and table assembly drawing Table Clamp Extend Arm Support Clamp Gear, Helical Worm, Elevation Column Collar Table Wire Stabilizer When ordering a part from this drawing, add an “B” prefix to the part number. SKU 44846 Page 14...
  • Page 15: Limited 1 Year / 90 Day Warranty

    1 year / 90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high qual- ity and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.

Table of Contents