Table of Contents
Advertisement
Cordless
Steel
Wood
Driver Dr i I I
Wood
screw
Machine screw
Nuts
MODEL 6012HD
MODEL 6012HDW
With Fast Charger and Carrylng Case
6 5
mm
1114"l
INSTRUCTION MANUAL
1 5 mm
5 . 1 mm
x
55
mm
6 mm
261
mm
1.6 kg
1518")
13/16"
x
2-118")
1114")
I
: E m )
1
400
'
lrloo
1
110-114")
1
13.5 lbsl
S PECl F I CAT1
0
N S
Battery Cartridge 9 0 0 0
Model 6012HD
9
Model DC9700 Fast Charger
Voltage
Input
output
Charging time
*
Manufacturer reserves the right to change specifications without notice
* Note: Specifications may differ from country to country.
Advertisement
Table of Contents
Related Manuals for Makita 6012HD
Summary of Contents for Makita 6012HD
- Page 1 Driver Dr i I I Cordless MODEL 6012HD MODEL 6012HDW With Fast Charger and Carrylng Case INSTRUCTION MANUAL S PECl F I CAT1 Model 6012HD Steel Wood Wood screw Machine screw Nuts 1 5 mm 5 . 1 mm 6 mm 1.6 kg...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 DISCONNECT TOOLS. When not in use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on.
- Page 4 SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) AWG Size of Cord not operate charger w i t h damaged cord or plug - replace them imme- diately. Do not operate charger if has received a sharp blow, been dropped, or otherwise damaged in any way;...
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE BELOW 10°C (5O0F1 Do not charge Battery Cartridge when temperature is or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used.
- Page 6 Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both Set plate sides of the cartridge while withdrawing it from the barrel.
- Page 7 When charge new battery cartridge or battery cartridge which has not been used for a long period, it may not accept a full charge. This i s normal condition and does not indicate problem. You can recharge the battery cartridge fully after discharging almost completely a couple of times.
- Page 8 Drill *Punch small hole in the metal to pre- vent the bit from skitterring when start- ing to drill a hole. machine oil on the bit to facilitate drill ing. .Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve t o damage the tip of your drill bit, decrease your drilling per- formance and shorten the service of the tool.
- Page 9 Screw Item Nominal diameter (mm) Match vour bit to vour screw. Wood screw Machine screw M2 - - 2.7 M2.6 Phillips bits Phillips bit No. 2-65 mm is standard M5.5 equipped. Select your screws and nominal diameter with the chart on the right.
- Page 10 Speed changeover change the speed, turn the speed change knob 180" while the drill is run- ning. Be sure that the speed change knob i s turned to the correct speed setting before you begin operation. See arrow indication. Use the right speed for the job.
- Page 11 *The hole the heel of the tool is a con- venient way to carry it by a cord, hook or other means.
- Page 12 ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk injury to persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 13 Tool carrying case Tool holster Part No. 823085-7 (Steel case) has some bits storage space. No. 824145-8 Part (Plastic case) holster t o carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No.
- Page 14 CORDLESS DRIVER DRILL Model 6012HD Note: The switch and other part configurations may differ f r o m country to country...
- Page 15 MODEL 6012HD F e b - 1 9 - 8 6 DESCRIPTION ' , " I ; , DESCRIPTION MACHINE ______ Head Screw M5x18 Steel Ball 4 8 Drill Chuck S 1 0 Clutch Cam Spindle Conical Compression Spring 1 6 - 2 1 Pi"...
- Page 16 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.