Scag Power Equipment SW Operator's Manual
  1. Manuals
  2. Brands
  3. Scag Power Equipment Manuals
  4. Lawn Mower
  5. SW
  6. Operator's manual
Scag Power Equipment SW Operator's Manual

Scag Power Equipment SW Operator's Manual

Hide thumbs Also See for SW:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
MODEL SW

Advertisement

Table of Contents
loading

Related Manuals for Scag Power Equipment SW

Summary of Contents for Scag Power Equipment SW

  • Page 1 MODEL SW...
  • Page 2 WARNING: REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR! Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment.

  • Page 3: Equipment Safety

    Make sure every operator is properly trained and thoroughly familiar with all of the controls before oper- ating the equipment. - Scag Power Equipment - GENERAL SAFETY INSTRUCTIONS...

  • Page 4: While Operating

    EQUIPMENT SAFETY CONT'D WHILE OPERATING WARNING:...

  • Page 5: Maintenance And Storage

    EQUIPMENT SAFETY CONT'D WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109 MAINTENANCE AND STORAGE OPERATION INITIAL RUN-IN...

  • Page 6: Mower Operation

    OPERATION CONT'D NOTE: MOWER OPERATION NOTE:...

  • Page 7: Cutter Deck Belt Adjustments

    OPERATION CONT'D NOTE: END OF L-SHAPED WARNING: BRACKET BELT "J" BOLT WASHER CUTTER DECK DRIVE BELT TENSION ALIGNMENT IDLER - L.H. SC400G Figure 1 WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109 BELT ADJUSTMENTS ire pressure can be adjusted for CUTTER DECK BELT ADJUSTMENTS WASHER SC401G...

  • Page 8: Drive Controls

    ADJUSTMENTS CONT'D CUTTER DECK BELT TENSION ADJUSTMENT ADJUSTMENT IDLER IDLER NEUTRAL LATCH DISCHARGE AREA NEUTRAL LOCK POSITION DRIVE POSITION CHECK BLADE DRIVE BELT TENSION HERE SC402G 3/4" Figure 3 STEERING BRAKE LEVER SC404G DRIVE CONTROLS Figure 5 NOTE: TRANSMISSION DRIVE BELT BAIL TRACTION PLUS LEVER...
  • Page 9 ADJUSTMENTS CONT'D SPACERS REPOSITIONING SPACERS SC406G Figure 7 LOW CUT (1 3/4"- 3") MID RANGE (2 1/2"- 3 3/4") HIGH CUT (3 1/4"- 4 1/2") CUTTER DECK HEIGHT ADJUSTMENT SC405G Figure 6...

  • Page 10: Cutter Blades

    ADJUSTMENTS CONT'D CUTTER BLADES BLADE HEIGHT ADJUSTMENT NOTE: NOTE: ANGLE BLADE BACK DO NOT CUT IN X MUST NOT EXCEED 1/3 BLADE WIDTH SC4O8G Figure 9 SC407G Figure 8...

  • Page 11: Lubrication And Maintenance

    LUBRICATION & MAINTENANCE BREAK-IN 8 HOURS (DAILY) 40 HOURS (WEEKLY) 100 HOURS (BIWEEKLY) 500 HRS OR ANNUALLY COMMENTS PROCEDURE REPLACEMENT PARTS Part Description 48110 Cutter Blade 16-1/2" 48184 Cutter Blade 16-1/2" High Lift 48108 Cutter Blade 18" 48185 Cutter Blade 18" High Lift 48111 Cutter Blade 21"...
  • Page 12 LUBRICATION & MAINTENANCE BREAK-IN 8 HOURS (DAILY) 40 HOURS (WEEKLY) 100 HOURS (BIWEEKLY) 500 HRS OR ANNUALLY COMMENTS PROCEDURE REPLACEMENT PARTS Part Description 48110 Cutter Blade 16-1/2" 48184 Cutter Blade 16-1/2" High Lift 48108 Cutter Blade 18" 48185 Cutter Blade 18" High Lift 48111 Cutter Blade 21"...
  • Page 13 32" & 36" CUTTER DECKS SC409GC...
  • Page 14 32" & 36" CUTTER DECKS Ref. Part Ref. Part No. Number Description 32 36 No. Number Description 32 36 48924 Pulley 46849 Cutter Deck (Includes Decals) 48926 Tapered Hub 46850 Cutter Deck (Includes Decals) 04001-01 Hex Hd. Bolt, 1/4-20 x 3/4" 46631 Cutter Spindle Assy.
  • Page 15 48", 52", 61", & 72" CUTTER DECKS 56, 56A 62, 62A 55 54 SC410GB...
  • Page 16 48, 52, 61, & 72" CUTTER DECKS Ref. Part Ref. Part No. No. Description 48 52 61 72 No. No. Description 48 52 61 72 04020-09 Nut, 5/8-11 Hex 46851 Cutter Deck (Includes decals) 48923 Pulley, Double 46751 Cutter Deck (Includes decals) 46A 48940 Pulley, Double 46752...

  • Page 17: Engine Deck

    ENGINE DECK KA Only BV Only BV Only (1 loc.) CVE Only CVE Only KA Only 40, 40A CVE Only CVE Only 390S0009...
  • Page 18 Lock Washer,7/16" 48126 Rubber Boot 32A 04001-101 Bolt, 7/16-20 x2-1/2" Hex Head 81A 43100 Wheel Axle (SW 52,61,72) * 32B 04001-102 Bolt, 7/16-20 x 1-3/4" Hex Head 81B 43085 Wheel Axle (SW36,48) * 32C 04002-15 Cpsrw, M10-1.5 x55 Metric Hex Hd...

  • Page 19: Handle Assembly

    HANDLE ASSEMBLY 45,45A REF. 57 61 TRACTION PLUS ACCESSORIES (OPTIONAL) (RVS-SM) (RVS-LG) 390S0010A...
  • Page 20 14KH 14KA 18BV 18BVE 14KH 14KA 18BV 18BVE 14KAE 14KAE 46801 Handle Assembly (Fits SW 36,48) 04050-09 Retaining Ring, 5/8 Ext. Basic 04017-06 Capscrew, 1/4-20 x 1" Ser. Flange x 46856 Handle Assembly (Fits SW52,61,72) x 04003-01 Bolt, 1/4-20 x 6" Carriage...
  • Page 21 INSTRUMENT PANEL S S C413GB REF. PART 13KH 13KA 16BV DESCRIPTION 14KH 14KA 18BV 18CVE 48717 Switch, Neutral Interlock 2A 481071 Throttle Control 2B 48946 Throttle Control 48787 Engagement Switch, Electric Clutch (Inc. hardware) 4A 48609 Key Switch (Includes hardware) 4B 48798 Key Switch (Includes hardware) 48023...
  • Page 22 PEERLESS 700-070 FOR REFERENCE ONLY ORDER PARTS FROM PEERLESS / TECUMSEH 778125 Spur Rear (35 teeth) 772083A Case, Transmisson 778239A Spur Gear (32 teeth-steel) 780086A Needle Bearing Grease Spec 778124A Spur Gear (30 teeth) 780142 Needle Bearing 778123A Spur Gear (25 teeth) 770061A Case, Transmission 778145...

  • Page 23: Handle Wire Harness - Electric Start

    HANDLE WIRE HARNESS - ELECTRIC START FUSES PART NO. 481267 RELAY MOWER ENGAGE KEYED SWITCH SWITCH TERMINAL BLACK GREEN BLACK BLUE OPERATOR PRESENCE WHITE TO ENGINE SWITCH DECK WIRE YELLOW HARNESS HOURMETER SC415GA MOWER ENGAGE KEY SWITCH SWITCH MOUNTING MOUNTING HOURMETER WIRE HARNESS WITH RELAY PART NO.

  • Page 24: Engine Deck Wire Harness - Kawasaki

    ENGINE DECK WIRE HARNESS - NEUTRAL KAWASAKI INTERLOCK PART NO. 481074 ENGINE REGULATOR BLACK BLACK BLUE WHITE WHITE BLADE YELLOW CLUTCH INSTRUMENT PANEL HARNESS GROUND SC417G HANDLE WIRE HARNESS - MANUAL START PART NO. 481266 MOWER ENGAGE KEYED SWITCH SWITCH TERMINAL WHITE BLACK...
  • Page 25 REGULATOR NEUTRAL INTERLOCK GREEN BLACK BLACK BLUE WHITE BLUE WHITE YELLOW BLADE CLUTCH FUSE INSTRUMENT PANEL HARNESS GROUND POS. BATTERY SOLENOID...
  • Page 26 BLADE CLUTCH NEUTRAL INTERLOCK GROUND BLACK ENGINE BLACK BLUE WHITE YELLOW WHITE WHITE YELLOW GREEN INSTRUMENT PANEL HARNESS FUEL SOLENOID (B & S) SOLENOID SOLENOID MOUNTING SOLENOID...

  • Page 27: Engine Deck Wire Harness - Kohler Command V-Twin

    ENGINE DECK BLADE CLUTCH WIRE HARNESS - KOHLER NEUTRAL (SINGLE CYLINDER) INTERLOCK GROUND & BRIGGS VANGUARD PART NO. 481073 BLACK BLACK BLUE WHITE WHITE YELLOW WIRE HARNESS ADAPTER - ENGINE INSTRUMENT SC421G PANEL HARNESS ENGINE DECK TRANSMISSION WIRE HARNESS - ENGINE GROUND KOHLER COMMAND...
  • Page 28 CAUTION BEFORE OPERATING READ OPERATORS MOWER DECK ON MANUAL AND SAFETY PULL UP AND INSTRUCTIONS PUSH FORWARD TO ENGAGE CAUTION MOWER DECK OFF KEEP BYSTANDERS AWAY PULL BACK TO DISENGAGE 481121 481121 CHOKE FAST SLOW 481122 CHOKE FAST SLOW 481270 FAST SLOW 481271...

  • Page 29: Operating Machine

    PARKING BRAKE FAST SLOW 481483 DANGER SPINNING BLADE KEEP CLEAR CONTACT CAN INJURE 48071 48404 48071 48404 WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL 481039 481039 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS: HEAVY DUTY 4,487,006 4,991,382 4,885,903...
  • Page 30 WARNING ROTATING BLADES AND BELTS KEEP HANDS, FEET & CLOTHING CLEAR KEEP ALL GUARDS IN PLACE SHUT OFF ENGINE & DISENGAGE BLADE CLUTCH BEFORE SERVICING CLEAR AREA OF DEBRIS BEFORE MOWING USE CAUTION IN DIRECTING DISCHARGE KEEP BYSTANDERS, CHILDREN & PETS AWAY READ INSTRUCTION MANUAL BEFORE OPERATING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING KIT, OR ENTIRE GRASS CATCHER INSTALLED...

This manual is also suitable for:

Sw series

Table of Contents