S/M No. : WF200TA001 Service Manual Auto Washer Model: DWF-200TATC Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center.
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER...
1. SPECIFICATIONS ITEM DWF-200TATC POWER SOURCE 110V / 60HZ POWER CONSUMPTION 550 W WEIGHT 47KG DIMENSION (W X H X D) 630 X 1040 X 670 mm WASHING COURSE FULL AUTOMATIC 6 COURSE (FUZZY, HEAVY, BLANKET, LIGHT, ECO., WOOL) WATER CONSUMPTION...
2. STRUCTURE OF THE WASHING MACHINE The parts and features of your washer are illustrated on this page. Become familiar with all parts and features before using your washer. NOTE • The drawings in this book may vary from your washer model. They are designed to show the different features of all models covered by this book, Your model may not include all features.
3. DIRECTIONS FOR INSTALLATION AND USE INSTALLING PLACE Install the washer on a horizontal solid floor. If the washer is installed on an unsuitable floor, it could make considerable noise and vibration. Never install in these places The place where it would be exposed to direct sunlight.
§• §• How to Connect the Inlet Hose Be careful not to mistake in supplying between the hot(maximum : 50˚C) and cold water. In using only one water tap or in case of attached one water inlet valve, connect the inlet hose to the cold water inlet valve.
Page 7
CLEANING THE LINT FILTER • This washer has two Lint Filters in the top TUB in order to filter off lint and fuzz. Pull the Filter frame Turn the lint filter Return the filter as it was, and upward. inside out, wash to insert the filter frame into the the lint off with water.
4. FEATURE AND TECHNICAL EXPLANATION Feature of the Washing Machine 1 First applying the Radical Technology in the world ... go beyond washing, sterilize your clothes and deodorize a bad smell. 2 The first air bubble washing system in the world. 3 Quiet washing through the innovational low-noise design.
Functional Principle of Bubble Washing Machine ACROSS SECTION Air bubble Outer tub Pulsator FUNCTIONAL PRINCIPLE Bubble Motor supplies the air from the bottom of outer tub to the inner space of pulsator, the air is dispersed by the rotation of pulsator. Air-bubble is created by the centrifugal force, and rises up. Automatic Drainning time Adjustment This system adjusts the draining time automatically according to the draining condition.
Automatic Unbalance Adjustment This system is to prevent abnormal vibration during intermittent spin and spin process. FUNCTIONAL PRINCIPLE Contact of safety switch 1. When the lid is closed, the contact lever A of the safety switch is “ON” position. Lid closing 2.
Lint Filter Much lint may be obtained according to the kind of clothes to be washed and some of the lint may also stick to the clothes. To minimize this possibility a lint filter is provided on the upper part of the tub to filter the wash water as it is discharged from the water channel.
Gear Mechanism Ass y The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the small sized clothes. Sun gear Planetary gear Internal gear Motor Pulsator 1800 r.p.m (60Hz) 1500 r.p.m (50Hz) Gear unit as V-Belt 1 revolution...
5. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT Warning BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE WASHING MACHINE, DISCONNECT THE POWER CORD FROM THE ELECTRIC OUTLET. Gear Mechanism Ass’y Replacement GEAR MECHANISM ASS’Y REPLACEMENT Separate the TOP PLATE from the washing Remove CAP PULSATOR form PULSATOR machine using screw driver.
Page 14
Separate TUB I from TUB ass’y. Lay the top of the washing machine on the floor. Unscrew 4 special bolts of GEAR PROTECT using a box wrench and separate GEAR PROTECT . Unscrew 4 special bolts of GEAR MECANISM Separate GEAR MECANISM and V-BELT. using a box wrench.
MOTOR DRAIN AND VALVE REPLACEMENT (NON PUMP MODEL) Lay the top of the washing machine on the floor. Take out the wire of MOTOR DRAIN. Unscrew 2 special bolts mounting MOTOR DRAIN. Separate MOTOR DRAIN from BASE. Turn the valve using screw driver as shown picture. Separate the valve lid from VALVE DRAIN assay.
6. THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM The structure of gear mechanism TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLY Tool name Specification Q’ty Fixing jig Ratchet handle Socket and extension bar socket : 10mm, 17mm per each Cotton Yarn some THE REPAIR...
How to check the clutch spring CHECKING METHOD IN THIS CASE, YOU MUST EMPTY THE SPIN TUB FIRST. 1) TO CHECK THE REVOLUTION OF SPIN TUB. IF THE SPIN TUB DOES NOT REVOLVE AND ONLY THE PULSATOR IS TURNING, THAT IS CLUTCH SPRING DEFECT.
The Process Of Disassembling Disassembling 1 Process Notice Use wrench or driver - ratchet handle - extension bar - socket : 10mm Remove the protector Release screws marked 4-point Remove the v-belt Use fixing jig for pulley as to see fig 1. and 17mm-socket for nut Loosen the fastening nut Take out plain washer if it has...
Page 19
Disassembling 2 Process Notice Disassemble the pulley Catch the boss and pull upward with spiral rotate in the clockwise direction Disassemble the clutch boss assembly Separate coupling from clutch boss ass’y Clean the drum plate, coupling surface and contact face between drum plate and coupling It is necessary to keep cotton...
The Process Of Assembling Assembling 1 Process Notice Check the uneven face of coupling is assembled upward Assemble the coupling - Push in the clutch boss ass’y with rotating on the clockwise direction. - After assembling, rotate on the clockwise more 2~3 teeth and pull out the pulley shaft upward Assemble the new clutch boss ass’y...
Page 21
Assembling 2 Process Notice - Use fixing jig and 17mm socket wrench as if disassembling, as fastening torque about Assemble the fastening nut 100~200kgf-cm. - Check the end-play, up and downward and check the binding force, too much or not on bi-direct of rotation.
7. TROUBLE SHOOTING GUIDE NOTES 1. When replace the P.C.B. ASS’Y do not scratch the surface of the P.C.B. ASS’Y. 2. Disconnect the power cord from the electric outlet. Concerning Water Supply PROBLEM CHECK POINT CAUSE SOLUTION Do you open the water Open the water tap.
PROBLEM CHECK POINT CAUSE SOLUTION Does the water supply The water inlet valve is Change the water inlet continue while the power defective. valve. is turned off? Does the water supply start The triac of P.C.B is Change the P.C.B as soon as you press the defective.
Concerning Draining PROBLEM CHECK POINT CAUSE SOLUTION Do you install the Install the drain hose Improper installation drain hose properly. properly? Is the accumulated Remove the foreign Malfunction of foreign substance substance from drainage by the THE WASHER inside the drain the drain housing foreign substance DOES NOT...
Concerning Spinning PROBLEM CHECK POINT CAUSE SOLUTION Is the lid open? Close the lid. Does the door switch Change the door switch. Door switch is defective. operate normally? Safety switch is Change the safety Does the safety switch defective. switch. operate normally? Is the connector of Connect the connector...
Concerning Operating PROBLEM CHECK POINT CAUSE SOLUTION Is the plug connected Connect the plug. to electric outlet? Is Fuse opened? Change Fuse Is the condition of INDICATOR Change P.C.B ASS’Y. Power button is defective power button good? LAMPS(L.E.D) DO NOT LIGHT UP WHEN THE Is the connector of the Improper connection of...
8. PRESENTATION OF THE P.C.B ASS’Y Concerning Error Message MESSAGE CAUSE SOLUTION Install drain hose properly. Improper installation of drain hose. Remove foreign matter from drain hose. The drain hose is blocked up by foreign matter. Change drain motor. Drain motor is inferior. Open the water tap.
§• §• Parts List No. PARTS CODE PARTS NAME DESCRIPTION Q'TY REMARK 3614530200 PLATE T 3618102500 NOZZLE DETERGENT 3611131700 CASE DETERGENT ABS, RINSE 3610907800 CAP SOFTENER 3614280100 PANEL B 36117AAX00 DOOR B ABS TRANSPARENT 3611425000 COVER DOOR B 3615110110 SPRING DOOR R EFF.
Page 34
No. PARTS CODE PARTS NAME DESCRIPTION Q'TY REMARK 3613226700 HOSE DRAIN O AS L=1250mm, HANGER 3614514600 PLATE UPPER 3615302220 SUPPORTER TUB BL SPG 1.6T(R-01) 3615302320 SUPPORTER TUB BR SPG 1.6T(R-01) 3615302420 SUPPORTER TUB FL SPG 1.6T(R-01) 3615302520 SUPPORTER TUB FR SPG 1.6T(R-01) 7122501211 SCREW TAPPING...
Page 35
No. PARTS CODE PARTS NAME DESCRIPTION Q'TY REMARK 3611417700 COVER TUB 3618807100 TUB O 1098 3619805400 SUSPENSION AS(B) ROD=592 SPR=102(BLACK) 3619805500 SUSPENSION AS(A) ROD=592 SPR=112(YELLOW) 3613208901 HOSE OVERFLOW PELD, L=280mm 3613218400 VALVE DRAIN AS VE TYPE 3613218500 HOSE DRAIN I AS LDPE+EVA, L=219.5 3610387400 BASE...
Page 36
DAEWOO ELECTRONICS CORP. 686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX: DWELEC K28177-8 CABLE: “DAEWOOELEC” S/M NO. : PRINTED DATE: Aug. 2006...