Set Mode Items - Icom IC-V80 Instruction Manual

Previous view
10
SET MODES

■ Set mode items

D Repeater tone frequency
Select the subaudible tone needed to access the re-
peater. A total of 50 tone frequencies (67.0–254.1 Hz)
are selectable. (default: 88.5 Hz)
D Tone squelch frequency
Select the CTCSS tone frequency to use for the Tone
Squelch function. A total of 50 tone frequencies (67.0–
254.1 Hz) are selectable. (default: 88.5 Hz)
• Usable subaudible tone frequencies
67.0 79.7 94.8 110.9 131.8
69.3 82.5 97.4 114.8 136.5
71.9 85.4 100.0 118.8 141.3
74.4 88.5 103.5 123.0 146.2
77.0 91.5 107.2 127.3 151.4
The transceiver has 50 tone frequencies and conse-
quently their spacing is narrow compared with units
having 38 tones. Therefore, some tone frequencies may
receive interference from adjacent tone frequencies.
D DTCS Code
Set the DTCS code (both encoder and decoder) for DTCS
squelch operation. A total of 104 codes are selectable.
(default: 023)
• Available DTCS codes
054 165
023 125 245
025 065 131 172 246
026 071 132 174 251
031 072 134 205 252
032 073 143 212 255
036 074 145 223 261
043 114 152 225 263
047 115 155 226 265
116 243 266
051 156
122 244
053 162 271
D DTCS Polarity
Set the Transmit and Receive DTCS polarity to "NN,"
"NR," "RN" or "RR."
The polarity for transmitting or receiving can be inde-
pendently set. (default: dtP.nn)
TX/RX: Normal polarity
(unit: Hz)
156.7 171.3 186.2 203.5 229.1
159.8 173.8 189.9 206.5 233.6
162.2 177.3 192.8 210.7 241.8
165.5 179.9 196.6 218.1 250.3
254.1
167.9 183.5 199.5 225.7
274 445 627
356 506 732
446 631
306 364 516 734
311 365 452 523 632 743
315 371 454 526 654 754
325 411 455 532 662
331 412 462 546 664
332 413 464 565 703
343 423 465 606 712
346 431 466 612 723
351 503 731
432 624
TX/RX: Reverse polarity
D Frequency offset
Set the duplex frequency offset between 0 and 20 MHz.
In the duplex mode, the transmit frequency shifts up or
down from the receive frequency by the offset amount.
(default: Depending on the transceiver versions)
D Reversed Duplex function
Turn the Reversed Duplex function ON or OFF (default).
When the Reversed Duplex function is ON, the receive
and transmit frequencies are reversed. (default: OFF)
D Tuning step
Set the VFO tuning step to 5, 10, 12.5, 15, 20, 25, 30 or
50 kHz. (default: differs depending on the version)
D Scan resume setting
Select the scan resume option from SCt. 5, SCt. 10,
SCt. 15, or SCP. 2.
• SCt. 5/10/15 : The scan pauses for 5 to 15 seconds, when
a signal is received. (default: SCt. 15)
• SCP.2 : The scan pauses, then resumes 2 seconds
after the signal disappears.
D Function key timer
Push [FUNC](M) to enter the Function mode, and then
push a keypad key to activate its second function.
• While in the Function mode, "
Set the time between when the Function mode is en-
tered, and how long it remains activated after you push
the keypad key to activate its second function.
• F0.At : Exits the Function mode immediately after a
key is pushed to activate its second function.
(default)
• F1/2/3.At : The Function mode remains activated 1, 2 or 3
seconds after a key is pushed to activate its sec-
ond function.
• F .m : The Function mode remains activated until
[FUNC](M) is pushed again, even after a key is
pushed to activate its second function.
38
" is displayed on the LCD.