1. Manuals
  2. Brands
  3. Haier Manuals
  4. Washer
  5. XQBM22-C
  6. Service manual

Haier XQBM22-C Service Manual

Mini computerized automatic washing machine
Hide thumbs Also See for XQBM22-C:
Table of Contents

Advertisement

Quick Links

See also: Use and Care Manual , User Manual
Mini Computerized Automatic Washing Machine
Service
Features
Ultimate design,compact structure
Water saving,energy-saving,time-saving
Erosion-proof shell,never getting rust
Better effect by soak-washing
Antiseptic resin,mould proofing and germicidal
Drainage protection program
Manual code:SM XQBM22-C-01
XQBM22-C
· þ Î ñ Ê Ö
Haier Group
Manual
XQBM22-C(America)
Edition: 2003.01.14

Advertisement

Table of Contents
loading

Related Manuals for Haier XQBM22-C

Summary of Contents for Haier XQBM22-C

  • Page 1 Mini Computerized Automatic Washing Machine · þ Î ñ Ê Ö Service Manual XQBM22-C(America) Features Ultimate design,compact structure Water saving,energy-saving,time-saving Erosion-proof shell,never getting rust Better effect by soak-washing Antiseptic resin,mould proofing and germicidal Drainage protection program Haier Group Edition: 2003.01.14 Manual code:SM XQBM22-C-01...

  • Page 2: Table Of Contents

    CONTENTS 1.Contents Product code illumination and series introduction 3. Features 4. Specifications 5. Safety precautions 6. Warning and cautions 7. Net dimension 8. Installation and accessory parts 9. Parts and functions 10. Maintenance service and trouble shooting 11. Wiring diagram 12.

  • Page 3: Features

    FEATURES Water saving,energy-saving,time-saving tainless steel inner tub Smaller volume,larger capacity Automatic power-off function Better effect by soak-washing Full plastic shell, stainless for ever Imbalance-revising function...

  • Page 4: Specifications

    SPECIFICATIONS Model XQBM22-C(America) Features for use Wash capacity Spin capacity Level/Volume 30/22/12 Preset × Residual dam pness Contral model contraller Normal computerized × Fuzzy computerized × Frequency conversion × Service features Programs Short cycle Inlet heating select × Heating selection ×...

  • Page 5: Safety Precautions

    SAFETY PRECAUTIONS Be sure to earth the earthing wire reliably. When the machine is normally using, please put the power plug at the location easily to be inserted and extracted by hand. Be sure to pull the plug off when there'spower failure, or the machine is being moved, cleaned or when it is idle.

  • Page 6: Warning And Cautions

    WARNING AND CAUTIONS Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children. Do not put any hot or heavy items Do not wash laundries with volatile ( such as the kettle with hot water ) materials (such as thinner, petrol etc.).

  • Page 7: Net Dimension

    NET DIMENSION Figure 1 Unit mm INSTALLATION AND ACCESSORY PARTS Usage of the drain hose The drainage shall be smooth with the drain hose. 1.Put the drain hose up to suitable position. The hanging height of drain hose should be in the fixed h<1.2m range: not more than 1.2m.
  • Page 8 INSTALLATION AND ACCESSORY PARTS How to change the direction of the drain hose 1.Lean the machine down gently with the 3.Extend the drain hose from the right side. Push the drain hose into the groove with front hands. Back Push the drain hose into the groove with Front hands at this point...
  • Page 9 INSTALLATION AND ACCESSORY PARTS The part of control panel seat 1)Method of opening the control panel A.Open the back cover. Loosen the locking belt fixed on the cabinet (used in inner wiring), to loosen the inner wiring. B.Loosen the four screws used to install the control panel seat (rear and side). Lift the rear upwards.

  • Page 10: Parts And Functions

    PARTS AND FUNTIONS Top lid Control panel seat Filter cover Inner tub Pulsator Cabinet Cabinet,lower Adjustable foot Figure 2 Cycle selection knob Control panel film Water level knob Power line Water inlet valve Water absorption gasket Handle Drain Hose Back cover Fixed Foot(3 Pcs) Figure 3...

  • Page 11: Maintenance Service And Trouble Shooting

    MAINTENANCE SERVICE AND TROUBLE SHOOTING If you replace the sequencer without checking the other components carefully, the sequencer may be damaged again. Therefore, please first check if the other components working normally before replacing the sequencer in maintenance. No action Confirm that there's no power failure, and the power plug is inserted reliably.

  • Page 12: No Water Filling

    MAINTENANCE SERVICE AND TROUBLE SHOOTING No water filling Switch on the power.Push the "Start/Pause"button Con- Exist Remove the foreign materials of the water inlet valve filter screen firm the action sound of or raise the water pressure to 0.03MPa-0.78MPa before use the water inlet valve Not exist Exist...

  • Page 13: Keep Filling Water

    MAINTENANCE SERVICE AND TROUBLE SHOOTING No draining Set rinse or spin.Start the machine Roll up normally Check if the drain Check the drain system like the drain valve etc. motor acts Exist -sure the voltage of Replace the drain motor the two ends of the drain motor Not exist Mea-...

  • Page 14: Too Much Spinning Noise

    MAINTENANCE SERVICE AND TROUBLE SHOOTING Too much spinning noise If the washing machine is Set the machine horizontally set horizontally If the hanger is wrongly used Replace the hanger If the noise of the motor is too much Replace the motor Fasten the motor If the motor is fastened tightly If the noise of the retarder is too much...

  • Page 15: Too Much Noise In Washing

    MAINTENANCE SERVICE AND TROUBLE SHOOTING Too much noise in washing If the noise of the motor is too much Replace the motor If the motor fastened tightly Fasten the motor If the noise of the retarder is too much Replace the retarder If the belt is too tight or loose Adjust the belt If the radiating pulley is loose...
  • Page 16 MAINTENANCE SERVICE AND TROUBLE SHOOTING Time-out in brake Chec Check if the k if the reset Set the reset spring to brake moment of the retarder spring of the retarder is at proper proper position is less than 3N.m position At this time please confirm that the brake moment of the retarder shall be within...

  • Page 17: Wiring Diagram

    WIRING DIAGRAM Pink Orange Water level switch Blue Black Grey Valve Black Yellow Black Puller White Purple White White Red/white Safety Red/white switch Motor Figure 4 There is overload protector installed in the motor. In case that the motor is overload or meets breakdown in working, the protector will act and stop the motor.

  • Page 18: Exploded View

    Sincere Forever...

Table of Contents