Advertisement
661MXPlus Motherboard Layout
IrDA Connector
(optional)
SPDIF_OUT
Connector (optional)
FDD Connector
PCI Expansion Slots
USB 2.0
Connectors
Speaker Connector
FAN1 Connector
Front Panel
Connector
Clear CMOS
SiS 964L
Jumper
Chipset
NOTE:
The above motherboard layout is provided for reference only;
please refer to the physical motherboard.
Easy Installation Guide
CD-IN
8X AGP
Front Audio
Connector
Connector
Slot
ATA 66/100/133
IDE Connectors
1
12V ATX Power
Connector
CPU FAN Connector
CPU Model Selection
Jumper
478-pin CPU Socket
SiS 661GX Chipset
184-pin DIMM Slots
ATX Power
Connector
P/N: 3A2507U00-000-G
V1.1
Advertisement
Table of Contents
Related Manuals for Foxconn 661MXPlus
Summary of Contents for Foxconn 661MXPlus
- Page 1 Easy Installation Guide 661MXPlus Motherboard Layout CD-IN IrDA Connector 8X AGP Front Audio Connector (optional) Connector Slot 12V ATX Power Connector SPDIF_OUT CPU FAN Connector Connector (optional) CPU Model Selection Jumper FDD Connector 478-pin CPU Socket PCI Expansion Slots SiS 661GX Chipset USB 2.0 Connectors 184-pin DIMM Slots...
-
Page 2: Rear Panel
Rear Panel 661MXPlus LAN Port Parallel Port (optional) (Printer Port) Line-in jack PS/2 Mouse Connector Line-out jack Microphone PS/2 Keyboard Connector jack Serial Port VGA Port USB 2.0 Ports (COM1) (optional) PS/2 Mouse Connector This green 6-pin connector is for a PS/2 mouse. PS/2 Keyboard Connector This purple 6-pin connector is for a PS/2 keyboard. -
Page 3: Accessory Checklist
Accessory Checklist Thanks for your purchasing Foxconn’s 661MXPlus series motherboard. Please carefully check the package; if there are any missing or damaged items, contact your distributor as soon as possible. v661MXPlus motherboard (x1) vFoxconn Utility CD (x1) vEasy Installation Guide (x1) - Page 4 1. Clear CMOS Jumper: CLS_CMOS You can clear CMOS to restore default system setting. To clear the CMOS, follow the procedures described below. 1. Turn off the system and unplug the AC power. 2. Remove ATX power cable from PWR1 connector. 3.
-
Page 5: Front Audio Connector
3. CPU FAN & FAN1 Plug the CPU cooling fan cable into the 3-pin CPU FAN power supply on the motherboard. Connect the case cooling fan connector to FAN1. SENSE +12V CPU FAN +12V SENSE FAN1 4. Front Audio Connector The audio interface provides two kinds of audio output choices: the Front Audio, the Rear Audio. -
Page 6: Front Panel Connector
5. CD_IN Connector CD_IN is Sony standard CD audio connector, it can be connected to a CD-ROM drive through a CD audio cable. CD_R CD_L CD_IN 6. Front Panel Connector Attach the power LED, IDE LED, reset switch and power switch connectors to the corresponding pins. -
Page 7: Speaker Connector
7. Speaker Connector The speaker connector is used to connect the speaker of the chassis. SPKJ EMPTY SPEAKER 8. SPDIF Out Connector (optional) The SPDIF output connector is capable of providing digital audio to external speakers, or compressed AC3 data to an external Dolby digital decoder. EMPTY SPDIF_OUT SPDIF_OUT... -
Page 8: Usb 2.0 Connectors
9. USB 2.0 Connectors The F-USB 1/2 connectors are available for additional USB ports if the USB ports on the rear panel are inadequate. Compared to traditional USB 1.1 with the speed of 12Mb/s, USB 2.0 has a fancy speed up to 480Mb/s, which allows faster Internet connection, interactive gaming, and simultaneous running of high-speed peripherals. - Page 9 10. IrDA Connector (optional) This header supports wireless transmitting and receiving devices. Before using this function, Configure the settings of IR mode from the “Integrated Peripherals” section of the CMOS Setup Utility. IRTX IRRX Empty 11. 6-channel Audio Effects The motherboard is equipped with the CODEC ALC655 chip, which provides supp- ort for 6-channel audio output, including 2 front, 2 rear, 1 center and 1 subwoofer channel.
- Page 10 Utility. Choose “Load Optimized Defaults” for recommended optimal performance. Select this option and press <Enter>. 13. Foxconn Utility CD This motherboard comes with one Utility CD. To begin using the CD, simply insert the CD disc into the CD-ROM drive. The CD will automatically bring up the main menu screen.