Page 1
® ELECTRONIC ELECTRICDRYER For questions about features, operation/performance, parts, accessories or service call: 1-800-253-1301 or visit our website at... www.whirlpooLcom Table of Contents ..........8530051...
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER"...
INSTALLATION INSTRUCTIONS Check that you have everything necessary for correct installation. Pedestal Proper installation is your responsibility. • Flat-blade screwdriver • Safety glasses Are you placing the dryer on a pedestal? You may purchase a pedestal separately for this dryer. This pedestal will add about •...
Dryer Dimensions (96.52 Explosion Hazard Keep flammabme materiame and vapors, such as gasoline, away from dryer= Place dryer at least 18 inches (48 cm) above the floor (80 cm) 27" for a garage installation= (6&6 cm) *Most installations require a minimum 51/2 '' (14 cm) clearance Failure to do so can result in death, explosion, or fire.
Page 6
Recessed or closet installation - Dryer on pedestal _l_lJ14,,mox..__ It is your responsibility • To contact a qualified electrical installer. • To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances. The National Electric Code requires a 4-wire supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.
Page 7
If using a power s upply cord: Use a ULapproved power s upply c ordkitmarked foruse with GROUNDING INSTRUCTIONS clothes d ryers. The kitshould contain: m For a grounded, cord-connected dryer: • AULapproved 30amppower supply cord, r ated This dryer must be grounded. In the event of malfunction or 120/240-volt minimum.
Page 8
Power Supply Cord Direct Wire Fire Hazard Fire Hazard Use 10 gauge solid copper wire, Use a new UL listed 30 amp power supply cord. Use a UL _isted strain relief, Use a UL listed strain relief, Disconnect power before making e_ectdcal connections. Disconnect power before making e_ectrica_ connections.
Remove center terminal block screw. Electrical Connection Options Remove appliance ground wire (green with yellow stripes) If your home has: And you will be Go to Section from external ground conductor screw. Fasten it under center, connecting to: silver-colored terminal block screw. 4-wire receptacle A UL listed, 4-wire connection:...
Page 10
Place the hooked ends of the other power supply cable wires 4-wire connection: Direct wire under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. IMPORTANT: A 4-wire connection is required for mobile homes !I !I and where local codes do not permit the use of 3-wire connections, Direct wire cable must have 5 ft (1.52 m) of extra length so dryer...
Page 11
3. Place the hooked ends of the other power supply cable wires 3-wire connection: Direct wire under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. Use where local codes permit connecting cabinet-ground conductor to neutral wire. !! !! Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.
Page 12
DURASAFF Mvent products are recommended. DURASAFF Mvent products can be purchased from your dealer Optional exhaust installations or by calling Whirlpool Parts and Accessories. For more This dryer can be converted to exhaust out the right side, left information, see the "Assistance or Service"...
Page 13
Determine Vent Length 1. Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking.
3. Determine the number of elbows you will need. IMPORTANT: Do not use vent runs longer than those specified in the Vent Length Chart, The following chart helps you determine your maximum vent length based on the number of 90 ° turns or elbows you will need and the type of vent (rigid or flexible metal) and hood Excessive Weight Hazard that you will use.
Page 15
Check the levelness of the dryer. Check levelness first 1. Check to be sure all parts are now installed. If there is an side to side, then front to back. extra part, go back through the steps to see which step was skipped.
DRYER USE 0 S_nsJng Heavy Duty JVormal 0 H_gh 0 v_Jp OMor_ Bulkyo/_// 0 Medium 0 Co_IOvwll Items I___ k O CydeComplete OLess CQstIQa 0 Low 0 Louder ,7buch Up OPbink,eShleld De/Jcqte_ Extra Low Softer Dryness 7vntm/Locked Level 0 On 0 Air Only 0 Off Manual Cycles...
Page 17
To unlock: To use a Manual Cycle Press and hold the END OF CYCLE SIGNAL button for 3 seconds • Rotate the dial to select a Manual Cycle. to turn this feature off. Press MORE TIME or LESS TIME until the desired drying time NOTE: When the dryer is running and Control Locked is on, the is displayed.
WRINKLE SHIELD Feature Cycle tips • Dry most loads using the preset cycle settings. The WRINKLE SHIELD feature light glows when this option is selected. This indicator stays on with the Cycle Complete light. • Refer to the Automatic or Manual Preset Cycle Settings chart (in the "Cycles"...
Automatic Preset Cycle Settings Automatic Cycles Temperature Time* Load Type (Minutes) WRINKLE SHIELD Feature When you are unable to remove a load of clothes from the dryer HEAVY DUTY High as soon as it stops, wrinkles can form. The WRINKLE SHIELD Heavyweight, towels feature periodically tumbles, rearranges and fluffs the load to avoid wrinkles.
3. Put the wet items on top of the rack. Leave space between When using Air Only the items so air can reach all the surfaces. • Check to see that coverings are securely stitched. NOTE: Do not allow items to hang over the edge of the rack. •...
DRYER CARE Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup. To wash Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.
Moving care The dryer light automatically turns on inside the dryer drum when you open the door. To change the drum light 1. Unplug dryer or disconnect power. 2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer.
United States. If you need replacement parts To locate the Whirlpool designated service company in your area, If you need to order replacement parts, we recommend that you you can also look in your telephone directory Yellow Pages. use only FSP® factory specified parts. These parts will fit right...
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for FSP _ replacement parts and repair labor costs to correct defects in materials or workmanship.