Table of Contents
Advertisement
Available languages
Available languages
Temperature
is too warm
•
New installation?
Allow 24 hours following installation for the
refrigerator to cool completely.
•
Door(s} opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully
closed.
•
Large load of food added? Allow several hours for
refrigerator to return to normal temperature.
•
Controls
set correctly
for the surrounding
conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See "Using the Controls."
There is interior moisture
buildup
NOTE: Some moisture build-up is normal.
•
Humid room? Contributes to moisture build-up.
•
Door(s} opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully
closed.
The ice maker is not producing
ice or not enough ice
•
Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
•
Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.
•
Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.
•
New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
•
Large amount of ice recently removed?
Allow 24 hours for
ice maker to produce more ice.
•
Ice cube jammed
in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.
•
Reverse osmosis
water filtration
system connected
to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
•
Water shutoff valve not fully open? Turn the water shutoff
valve fully open.
•
Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.
•
Reverse osmosis
water filtration
system connected
to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
•
Questions remain regarding
water pressure?
Call a
licensed, qualified plumber.
Off-taste,
odor or gray color in the ice
•
New plumbing connections? New plumbing connections
can cause discolored or off-flavored
ice.
•
Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.
•
Odor transfer
from food? Use airtight, moisture proof
packaging to store food.
•
Are there minerals
(such as sulfur) in the water? A water
filter may need to be installed to remove the minerals.
•
Is there a water filter installed
on the refrigerator?
Gray or
dark discoloration
in ice indicates that the water filtration
system needs additional flushing.
The ice dispenser
will not operate properly
•
Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
•
Ice bin installed
correctly?
Be sure the ice bin is firmly in
position.
•
New installation?
Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
•
Ice stuck in the delivery chute? Use a plastic utensil to clear
the delivery chute.
•
Has the wrong ice been added to the bin? Use only cubes
produced by the current ice maker.
•
Has the ice melted around the auger (metal spiral} in the
ice bin? Dump the ice cubes and clean the ice bin.
Cut Hazard
Use a sturdy glass when diepensing
ice or water.
Failure to do so can result
in cuts.
•
Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed" ice and begin dispensing again.
•
Has the dispenser
arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
Page 10
Hide quick links:
Advertisement
Table of Contents
