CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. COMPLIANCE: The responsible party for this product’s compliance is:...
SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
Page 4
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.
* For further information, refer to ‘Speaker & Speaker Stand’ manual. 2. POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indi- cated on the Specifications page. Never attempt to operate the Monitor on DC power.
(DVD/DTV INPUT) Connection to AV equipment Note: The connection cables shown above to the left are not included with the Monitor. A D-sub 15-pin cable and a DVI cable shown above to the right are provided to connect the Monitor to a PC.
- Connect the VIDEO INPUT socket (yellow) with the BNC-RCA adapter to the VIDEO INPUT on the Monitor. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the Monitor.
Page 9
- Connect the signal cable from the monitor output port of the PC to the RGB1 INPUT (PC/DTV INPUT) port of the Monitor or the signal cable from the DVI output port of the PC to the RGB2 INPUT (DIGITAL RGB INPUT) port on the Monitor and change the resolution output of PC accordingly.
Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the Monitor. - Under certain conditions or if the IR code from the remote is interrupted, a particular remote function may not occur.
Monitor Installation Options • The Monitor can be installed in different ways such as on a wall, or on a desktop etc. • Install this monitor only in a location where adequate ventilation is available. • This monitor can be mounted either horizontally or vertically.
Caution • When installing the monitor vertically, you have to change the OSD display mode so that the menus will appear correctly and also to protect the monitor from overheating (Refer to P. 18). • Install this monitor only in a location where adequate ventilation is available.
• Press the ON/OFF button on the Monitor to turn the Monitor on. 2. If the Monitor was turned off with the remote control and the ON/OFF button on the Monitor • Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on.
APC (Auto Picture Control) APC (Auto Picture Control) - This function adjusts the Monitor to the best picture appearance 1. Press the APC button to select the picture appearance setup option. • Each press of the APC button changes the menu option as shown below.
(Digital Auto Sound Processing) - This function lets you enjoy the best sound without any special adjustment because the Monitor automatically selects the appropriate sound option based on the program content. 1. Use the DASP button to select the appropriate sound setup.
Time Menu Options Setting the Clock Setting the Clock - If current time setting is erased by a power failure, if TV is unplugged, or if the monitor has been turned off with the ON/OFF button on the monitor, reset the clock.
Orbiter - Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining even after you change the image.
4. If picture needs to be adjusted more after Auto adjustment in RGB1(PC), you can adjust the MANUAL CONFIG. - Although the image is still not correct, your Monitor is functioning properly but needs further adjustment. - The and the AUTO CONFIG.
Screen Position Screen Position - Screen Position is available in the following modes: RGB1-PC, RGB1-DTV (480p,720p,1080i), RGB2-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i). 1. Press the MENU button and then use 2. Press the button and then use D / E D / E / F / G 3.
PIP (Picture-in-Picture) Feature - PIP lets you view 2 different inputs (picture sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - When you select PC or DTV for main picture in PIP, you can watch VIDEO, S-VIDEO or COMPONENT 480i for sub picture.
Twin Picture Main Picture Size Main Picture Size Adjustment Adjustment Use the TWIN PICTURE button. • Each press of the TWIN PICTURE button cycles through the screen displays shown below. DW 1 Sub Picture Size Adjustment Sub Picture Size Adjustment Use the WIN.SIZE button.
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
Page 24
0 ~ 64 0 ~ 64 0 ~ 1 01. Power (Command:a) 0 ~ 1 G To control Power On/Off of the Monitor. 0 ~ 3 Transmission 0 ~ 1 [k][a][ ][Set ID][ ][Data][Cr] 0 ~ 3...
Page 25
03. Aspect Ratio (Command:c) (Main picture format) G To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Special menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 0: Wide screen (16:9) 1: Normal screen (4:3) 2: Full screen (Zoom)
Page 26
Acknowledgement [l][ ][Set ID][ ][OK][Data][x] Data 0: OSD off 1: OSD on 13. Remote Control Lock Mode (Command:m) G To lock the front panel controls on the monitor Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 0: Lock off 1: Lock on...
Page 27
20. Color Temperature (Command:u) G To adjust color temperature. You can also adjust ACC in the Video menu. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0: Normal 1: Cool 2: Warm Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data 0: Normal 1: Cool 2: Warm 21.
How to Connect G Connect your wired remote control to the Remote port on the Monitor. Set the CONTROL LOCK to ‘ON’ on the Monitor back panel to operate Monitor with wired remote control. Remote Control IR Code (NEC Format)
Page 29
Code (Hexa) Function UP ( DOWN ( VOL+ ( VOL- ( POWER On/Off POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 AII INPUT SELECT...
Monitor • Check whether the Monitor is turned on. • Power cord inserted into wall outlet? • Plug another product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. • Press the VOLUME ( ) button.
Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor. Cleaning the Cabinet Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.