Choose from the options below: Visit us on the web at www.mtdproducts.com Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683 Write us at MTD LLC • EO. Box 361131 • Cleveland, OH • 44136-0019...
ImportantSafeOperation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Never run an engine indoors or in a poorly ventilated area. SafeHandling of Gasoline Engine exhaust contains carbon monoxide, an odorless To avoid personal injury or property damage use extreme care and deadly gas. in handling gasoline. Gasoline is extremely flammable and the Do not operate...
Maintenance & Storage Donot modify engine Never tamper with safety devices. Check their proper To avoid serious injury or death, do not modify engine in any operation regularly. Refer to the maintenance way. Tampering with the governor setting can lead to a runaway adjustment sections of this manual.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting assemble and operate...
Assembly & Set-Up Contentsof Carton One Snow Thrower Two Replacement Auger Shear Pins One Chute Assembly One Snow Thrower Operator's One Product Registration Card Manual Assembly Handle Place the shift lever in the forward-6 position. Observe the lower rear area of the snow thrower to be sure both cables are aligned with roller guides...
Page 8
ChuteDirectional Control Chute Clean-0ut Tool Remove the plastic cap (if present), flat washer and hairpin The chute clean-out tool is fastened to the top of the auger clip from the end of the chute directional control. See Fig. housing with a mounting clip and a cable tie at the factory.
Adding Fuel WARNING! Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition. equipment moving parts.
Page 10
Auger Control carefully read and follow all instructions below. WARNING! Prior to operating your snow thrower, Perform all adjustments to verify your snow thrower is operating safely and properly. Check the adjustment of the auger control as follows: When the auger control is released and in the disengaged "up"...
Controls a nd Features Drive Control Shift Lever er Control Gas Cap Chute Assembly Chute Directional Control Oil Fill Clean Out Tool Muffler Recoil Starter Primer Handle Throttle Control Choke Control Electric Start Augers Button Oil Drain Skid Shoe Electric Starter Outlet Figure 4-1 Snow thrower controls...
ThrottleControl AugerControl AUGER CONTROL The throttle control is located on the rear of the engine. regulates the speed of the engine and will shut off the engine when moved into the STOP position. Primer Pressing the primer forces fuel directly %_p_li into the engine's carburetor...
Page 13
Chute Directional Control ChuteClean-OutTool CHUTE DIRECTIONAL CONTROL clogged chute assembly. Shut offengine and remain ARNING! Never use your hands to clear a behind handles until all moving parts have stopped ADJUSTABLE before unclogging. CHUTE TiLT DISCHARGE DISCHARGE LEFT The chute clean-out tool is conveniently fastened to the rear of...
Operation Plug the extension cord into the electric outlet located Starting the Engine on the engine. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well- ventilated area. See Fig. 5-2. moving parts. Do not use a pressurized starting l_Jlhjk, ARNING!
RecoilStarter ToEngageDrive With the throttle control in the Fast(rabbit) position, move engine running. shift lever into one of the six forward (F) positions or two CAUTION! Do not pull the starter handle while the reverse (R) positions. Select a speed appropriate for the snow conditions and a pace you're comfortable with.
Maintenance& Adjustments Maintenance Lubrication GearShaft Engine Refer to the Engine Maintenance section. The gear (hex) shaft should be lubricated at least once a season or after every twenty-five (25) hours of operation. ShavePlate and Skid Shoes Carefully pivot the snow thrower up and forward so that it The shave plate and skid shoes on the bottom...
Page 17
Auger Shaft Adjustments At least once a season, remove the shear pins from the auger Shift Cable shaft. Spray lubricant inside the shaft and around the spacers and the flange bearings found at either end of the shaft. If the full range of speeds (forward and reverse) cannot be See Fig.
DriveControl ChuteBracketAdjustment When the drive control is released and in the disengaged "up" If the spiral at the bottom of the chute directional control is not position, the cable should have very little slack. It should NOT be fully engaging with the chute assembly, the chute bracket can be tight.
Engine Maintenance WARNING! To prevent accidental start-up, shut off Periodic inspection and adjustment of the engine is essential high level performance is to be maintained. Regular maintenance the engine and remove the ignition key before will also ensure a long service life. The required service intervals performing any type of engine...
Check that the spark plug washer is in good condition 5park Plug and thread the spark plug in by hand to prevent cross- threading. plug removed. DO NOT crank engine with spark After the spark plug is seated, tighten with a spark plug WARNING? DO NOT check for spark with spark plug removed.
Service Carefully pivot the snow thrower up and forward so that it Belt Replacement rests on the auger housing. Auger Belt Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure To remove and replace your snow thrower's auger belt, proceed it.
DriveBelt Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. To remove and replace your snow thrower's drive belt, proceed See Fig. 8-5. as follows: Place a piece of plastic under the gas cap. Remove the plastic belt cover on the front of the engine by removing the two self-tapping...
Friction WheelRemoval Slip the drive belt offthe pulley and between friction wheel and friction wheel disc. See Fig. 8-7. If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment fails to correct the problem, the friction...
Page 24
Carefully remove the hex nut which secures the hex shaft Follow the previous steps in reverse order to reassemble to the snow thrower frame and lightly tap the shaft's end to components. If you're disassembling the friction wheel and dislodge the ball bearing from the right side of the frame.
Troubleshooting Problem Cause Remedy Engine fails to start 1. Choke not in ON position. 1. Move choke to ON position. 2. Spark plug wire disconnected. 2. Connect wire to spark plug. 3. Fuel tank empty or stale fuel. 3. Fill tankwith clean, fresh gasoline.
Page 30
MTD. OWNER'S WARRANTY RESPONSIBILITIES: As the smalloff-roadengineowner,youare responsible forthe performance of the requiredmaintenance listed in your Owner'sManual.MTD recommends that you retainall yourreceiptscoveringmaintenances on yoursmall off-roadengine,but MTDcan not denywarrantysolelyfor the lack of receiptsor foryour failureto ensurethe performanceto all scheduledmaintenance. As the smalloff-roadengineowner,youshouldhoweverbe awarethat MTDmaydenyyour warrantycoverageif yoursmall off-roadengine or part hasfaileddue toabuse, neglect,impropermaintenance or unapprovedmodifications.
Page 31
(8)Throughout the engine's warranty period defined inSubsection (a)(2), MTD will m aintain a supply ofwarranted parts s ufficient tomeet the expected demand forsuch parts. (9)Any replacement part m ay b eused i ntheperformance...
MANUFACTURER'S LiMiTED WARRANTY The limited warranty set forth below is given by MTD LLC with c. Service completed by someone other than an authorized service dealer. respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited d.