Page 1
Safety Rules and Operating Instructions before first use of this product. • Safety Customer Help Line: 1-877-369-8665 • Features • Operation Sold by: Sears Canada Inc., Toronto M5B 2B8 • Maintenance Visit the Craftsman web page: www.sears.ca • Parts List 960223154-01 8-O3...
Page 2
WARRANTY ON CRAFTSMAN CORDLESS DRILL-DRIVER If this CRAFTSMAN power tool fails because of defects in material or workmanship within three years from the date of purchase, return it to the nearest Sears Canada Inc. ("Sears") store and "Sears" will repair it, free of charge.
Page 3
Your drill-driver has many features for making your drilling WARNING: Do not attempt to use this product until operations more pleasant and enjoyable. Safety, you read thoroughly and understand completely the performance and dependability have been given top operator's manual. Pay close attention to the safety priority in the design of this drill-driver making it easy to rules including Dangers, Warnings and Cautions.
Page 4
Tool Use and Care nails, screws, or other small metal objects that can make a connection from one terminal to another. • Use clamps or other practical way to secure and Shorting the battery terminals together may cause sparks, support the workpiece to a stable platform. Holding burns, or a fire.
Page 5
• That wire size is large enough for AC ampere _IWARNING: Never use a battery that has been rating of charger as specified below: dropped or received a sharp blow, A damaged battery Cord Length (Feet) 25' 100' is subject to explosion. Properly dispose of a dropped battery immediately.
Page 6
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second)
Page 7
90 in.lb. M_imum Torque Chuck 10mm (3/8 in.) Keyless CHARGER 1421414 Motor DC 12 Volt Gear Train One Speed Rating 120 V, 60 Hz,AC only Switch Variable Speed Charge Rate 3-6 Hours No Load Speed O-600/min. Clutch 24 Positions BATTERY PACK 130139012 KNOW YOUR DRILL-DRIVER...
Page 8
BIT STORAGE TORQUE SCREWDRIVER ADJUSTMENT RING BITS KEYLESS CHUCK DIRECTION OF ROTATION SELECTOR (FORWARD / REVERSE) CHARGING STAND RED_ LIGHT WRIST STRAP BATI'ERYPACK SHOWNINTOOL Fig. 1 CHARGER SeeFigurel.
Page 9
WARNING: Do not allow familiarity with your drill- driver to make you careless, Remember that a careless fraction of a second is sufficient to inflict severe injury, CHARGING BATI'ERY PACK See Figure 1. The battery pack for this tool has been shipped in a low charge conditionto prevent possible problems.
Page 10
SWITCH TO INSTALL BA'I-rERY PACK See Figure 2. • Lock switch trigger on your drill by placing the direction To turn your drill ON, depress the switch trigger. To turn it of rotation selector in center position. See Figure 4. OFF, release the switch trigger.
SWITCH LOCK KEYLESS CHUCK See Figure 4. See Figure 5. The switch trigger can be locked in the OFF position. This Your drill has a keyless chuck. As the name implies, you can feature can be used to prevent the possibility of accLdental hand tightenor release drillbits in the chuckjaws.
Page 12
REMOVING BITS INSTALLING BITS See Figure 6. See Figure 6. • Lock the switch trigger by placing the direction of • Lock the switch triggerby placing the direction of rotation selector in center position. See Figure 4. rotationselector in center position.See Figure 4. •...
Page 13
BIT STORAGE DRILLING See Figure 9. See Figure 10. When not in use, bits providedwith your drill can be placed in the storage area located on the bottomof your drill as shown in Figure 9. SCREWDRIVER BITS BIT STORAGE AREA Fig.
CHUCK REMOVAL • insert hex key in chuck and tighten chuck jaws se- curely. Tap sharply with a mallet in a counterclockwise See Figures 11, 12, and 13. direction. This will loosen chuck on the spindle. It can The chuck must be removed in order to use some now be unscrewed by hand.
Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury. TOOLS, VISIT YOUR NEAREST SEARS RETAIL STORE, OR A COMPLETE SELECTION OF ACCESSORIES FOR THIS AND OTHER CRAFTSMAN POWER AND BENCH|...
CRAFTSMAN 1 0mm(3/8in.),12VOLTCORDLESS D RILL-DRIVER - MODEL NO.973.225400 inallcorrespondence regarding your10mm (3/8 in.),12VOLT CORDLESS DRILL-DRIVER orwhen ordering I Themodel number will b efound onaplate attached tothemotor h ousing. Always m ention t hemodel number I repair parts. SEE BACK PAGE FOR PARTS ORDERING...
Page 18
Operator's Manual STOCK 9 22540 MODEL 973.225400 Sears service is available at or through your Sears Retail Store or Catalogue Sales Office, How to order repair parts When orderingrepair parts always give: SERVICE AND REPAIR PARTS 1. The Part Number CALL 1-800-665-4455 * 2.