Craftsman 315.271410 Owner's Manual

318 inch industrial electric drill variable speed adjustable-reversible double insulated

Advertisement

OWNER'S
MANUAL
MODEL NO.
315.271410
CAUTION:
Read Rules for
Safe Operation
and All Instruc-
tions Carefully
Thank You for Buying
Craftsman Tools
CRRFTSMRN"
318 INCH INDUSTRIAL
ELECTRIC DRILL
VARIABLE
SPEED
ADJUSTABLE-REVERSIBLE
DOUBLE
INSULATED
Warranty
Introduction
Operation
Maintenance
Repair Parts
Sears,
Roebuck
and Co., Hoffman
Estate,It_
60179
USA
612547-747
11-00

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman 315.271410

  • Page 1 Read Rules for Safe Operation 318 INCH INDUSTRIAL and All Instruc- ELECTRIC DRILL tions Carefully VARIABLE SPEED ADJUSTABLE-REVERSIBLE DOUBLE INSULATED Warranty Introduction Thank You for Buying Craftsman Tools Operation Maintenance Repair Parts Estate,It_ Sears, Roebuck and Co., Hoffman 60179 612547-747 11-00...
  • Page 2: Rules For Safe Operation

    FULL ONE YEAR WARRANTY ON CRAFTSMAN INDUSTRIAL ELECTRIC DRILL If thisCraftsman Industrial Electric Drill fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS STORE IN THE uNrrED STATES.
  • Page 3 CORDS. When alcohol, or any medication. tool is used Outdoors, use only extension cords When servicing use only identical Craftsman suitable for use outdoors. Outdoor approved cords replacement part==. are marked with the suffix W-A, for example - POLARIZIED PLUGS, To reduce the dsk of electric...
  • Page 4: Operation

    OPERATION KNOW YOUR ELECTRIC DRILL Before attempting touse anytool,familiarize yourself w ithalloperating features andsalaryrequirements. SeeFigure1. Make sure power supply Is 120 volts, 60 Hz, AC only. CHUCK AUXILIARY HANDLE REVERSE LEVER CHUCK KEY CONTROLSELECTOR SWITCH TRIGGER BELT CLIP CHUCK KEY HOLDER TRUSS HEAD SCREW Fig+ 1 Page 4...
  • Page 5 OPERATION INSTALLING AUXIUARY HANDLE See F_ure 1, AN AUXILIARY HANDLE IS PACKED WITH YOUR DRILL FOR EASE OF OPERATION AND TO HELP PREVENT LOSS OF CONTROL To install, start the screw threads into the threaded hole in the gear housing and tighten sac_re_/.
  • Page 6 OPERATION VARIABLE SPEED VARIABLE SPEED S6e Figure 4. CONTROL SELECTOR Your ddll has avadable speed control selector designed to allow operator control and adjustment of speed and torque limits. The speed and torque of your ddl] can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 4.
  • Page 7 OPERATION TO INSTALL BITS DRILL BIT See Figure 6. UNPLUG YOUR DRILL. Open or close the chuck jaws to a point where the opening is slightly la_er than the drill bit you intend to use. Also, raise the front of your drillslightlyto keep the drill bits from fallLngout of the chuck jaws.
  • Page 8 OPERATION DRILLING See Rgure 8. Depress and release the switch trigger to be sure your ddli is in "Off" position before connecting if to power supply. Check fhe direation of rotatton lever tor corTectsatting (ton_vard or reverse). See Figure 3. Secure the material fo be drilled in a viseor wit hclamps fo keep it from turning as the dd]l bit rotates.
  • Page 9: Chuck Removal

    OPERATION CHUCK REMOVAL See Figures 10, If, and 12. The chuck must be removed in order to use some accesso- des. TO remove; UNPLUG YOUR DRILL. Close the chuck jaws. Line up hole in spindle with slot in gear housing and insert a 1/8 in.
  • Page 10: Maintenance

    LUBRICATION All ofthe bearings in this tool are hibdcated with a sufficientamount of high grade lubricant for the life of the unit under norma; operating conditions, Therefore. no further lubricationis required. CRAFTSMAN CHUCK HOLDER F_rmaiaopbyforcingendwithroundholasthroughslotledbele0noppositeend.
  • Page 11: Parts List

    CRAFTSMAN 3/8 INCH INDUSTRIAL ELECTRIC DRILL - MODEL NUMBER 315.271410 The model number willbe found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3i8 INCH ELECTRIC DRILL or when ordedng repair pads,...
  • Page 12 For repairof major brand appliancesin your own home... no matter who made it, no matterwho sold it! 1-800-4-MY-HOME s" Anytime,day or night {1-800-469-4663) www,sears,com To bringin productssuch as vacuums,lawn equipmentand electronics for repair,call for the locationof yournearest Sears Parts & Repair Center. 1-800-488-1222 Anytime,day or night www.sears.com...

Table of Contents