Page 1
For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product.
Page 3
Your JL Audio amplifier employs an Your amplifier needs to be installed in a dry, advanced type of heat management, called well-ventilated environment and in a manner RealSink™. This feature takes advantage of which does not interfere with your vehicle’s safety...
Product descriPtion The JL Audio HD750/1 is a very powerful and compact monoblock (single channel), full-range amplifier utilizing patented Single Cycle Control™ Class D technology. This groundbreaking technology delivers reference- grade sonic performance while requiring far less current from the vehicle’s electrical system than a conventional amplifier.
Then insert any questions, please contact your authorized the power connector plug into the amplifier’s JL Audio dealer for assistance. power connector receptacle, pushing firmly. 1) Disconnect the negative battery post 9) Connect the RCA input cables connection and secure the disconnected cable to the amplifier.
“CCA” wire because the vehicle and your body during installation. this wire is significantly less conductive than pure copper wire. Only use pure copper power wire, such as JL Audio’s Premium Power Wire. +12 VDC Ground +12 VDC Ground Remote...
When using smaller wire, it may optimal grounding, we recommend the be necessary to strip 1 inch of insulation from use of a JL Audio ECS master ground lug the wire and fold the bare wire in half prior to (XB-MGLU). Alternatively, a sheet metal insertion.
(not included), secure the amplifier by its four Lateral Mounting Feet. Check before drilling any holes in your vehicle to make sure that you will not be drilling through a gas tank, brake line, wiring harness 8 | JL Audio - HD750/1 Owner’s Manual...
OEM (factory-installed) systems. To use speaker-level sources, splice the speaker output wires of the source unit or small amplifier onto a pair of RCA plugs for each input pair or use the JL Audio ECS Speaker Wire to RCA adaptor (XD-CLRAIC2-SW).
Appendix C (pages 18, 19). Doing so will result in Useful for connection of subwoofer(s) audible distortion and possible speaker damage. in a bi-amplified system. 10 | JL Audio - HD750/1 Owner’s Manual...
inFrasonic Filter 2) “Filter Slope” Control: This switch allows you The “Infrasonic Filter” is a 24 dB/octave high- to select from two filter slopes: pass filter, with a fixed cutoff frequency of 30 Hz. This filter is designed to conserve amplifier power “12dB”: Configures the filter to attenuate and protect subwoofer systems, without audibly frequencies above or below the selected...
If you change crossover slopes or crossover filter frequencies, you may need to revisit this control as these can affect the phase of the speaker systems in the overlap region. 12 | JL Audio - HD750/1 Owner’s Manual...
The RBC-1 Remote Bass Control used with JL Audio Slash, Slash v2, e-Series, A-Series and If you connect a load higher than 4Ω nominal, G-Series amplifiers is NOT compatible with the power will drop by half with every doubling of HD Series amplifiers.
Page 14
Do not chassis ground any speakers connected to this or any other JL Audio amplifier. Doing so will cause the amplifier to go into protection and mute the output.
Page 15
JL Audio dealer so that may require service of the amplifier, its that it may be sent in to JL Audio for service. wiring or the vehicle’s charging system. Audio There are no user serviceable parts or fuses inside is muted when this fault occurs.
Sens.” for the affected channels if any equalizer boost is activated after setting the “Input Sens.” with this procedure. This applies to any EQ boost circuit, source unit tone controls or EQ circuits. EQ cuts will not require re-adjustment. 18 | JL Audio - HD750/1 Owner’s Manual...
Page 19
the nine-step Procedure 1) Disconnect the Speaker Connector Plug. 6) Verify that you have disconnected the Speaker 2) Turn off all processing on the source unit Connector Plug before proceeding. Play a (bass/treble, loudness, EQ, etc.). Set fader track with an appropriate sine wave (within control to center position and subwoofer the frequency range to be amplified by each level control to 3/4 of maximum (if...
Check the input connectors to ensure that they all are making good contact with the input jacks on the amplifier. 20 | JL Audio - HD750/1 Owner’s Manual...
Page 21
“my amplifier shuts off once in a while, usually at higher volumes” Check your voltage source and grounding point. The power supply of the HD750/1 will operate with charging system voltages down to 8.5V. Shutdown problems at higher volume levels can occur when the charging system voltage drops below 8.5V.
Page 24
- amPliFiers (usa) JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years. The warranty is extended to three (3) years total if installation is performed by an authorized JL Audio dealer using a JL Audio Premium Power Connection System for power wiring.