Related Manuals for Zenoah PSZ2600
Summary of Contents for Zenoah PSZ2600
- Page 1 PSZ2600 115 37 31-10 (005) OWNER’S MANUAL POLE SAW PSZ2600 Original Language GB-1...
-
Page 2: Table Of Contents
PSZ2600 SAFETY FIRST Contents Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken 1. Parts location ..........2 into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions 2. -
Page 3: Specifications
Idle speed ....3000±200min-1(rpm) Oil pump ........... Plunger type Fuel ....Mixture (Gasoline 50 : Oil 1) Standard Accessories (when using ZENOAH genuine oil) Harness ..............1 pc. Carburetor ....Walbro Diaphragm type Tool Kit ..............1 pc. Spark plug ......... NGK CMR7A Guide bar cover ........... -
Page 4: For Safe Operation
PSZ2600 5. For safe operation WORKING PLAN 1. Read this manual carefully until you 1. You should never use the product completely understand and follow when under the influence of alcohol, all safety and operating instructions. when suffering from exhaustion or lack 2. - Page 5 Cut only materials recommended by the be sure to use only ZENOAH prod- manufacturer. And use only for tasks ex- ucts or products which have been plained in the manual.
- Page 6 PSZ2600 5. For safe operation HANDLING FUEL eral steps to keep cutting jobs free 1. The engine of the ZENOAH product from accident or injury. is designed to run on a mixed fuel, which contains highly flammable (1) With a basic understanding of kick- gasoline.
-
Page 7: Set Up
PSZ2600 6. Set up MOUNTING ENGINE A standard package contains the items as shown below. 1. Push the shaft tube toward the clutch housing and rotate it by hand to check that the power transmission shaft is en- gaged with the gears. 2. -
Page 8: Fuel And Chain Oil
WARNING It is very important to maintain the proper chain tension. • The Zenoah engines are lubricated by oil specially for- Rapid wear of the guide bar or the chain coming off eas- mulated for air-cooled 2-cycle gasoline engine use. If ily can be caused by improper tension. -
Page 9: Operation
PSZ2600 7. Fuel and chain oil 8. Operation careful that, if the agitation is insufficient, there is an WARNING increased danger of early piston seizing due to ab- normally lean mixture. The cutting head will start rotating upon the engine starts. 5. - Page 10 PSZ2600 8. Operation 6. While holding the unit firmly, pull out the starter rope quickly STOPPING ENGINE until engine fires. 1. Release the throttle lever and run the engine for half a minute. 2. Shift the ignition switch to the STOP position. IMPORTANT WARNING •...
- Page 11 PSZ2600 8. Operation Checking oil supply IMPORTANT After starting the engine, run the chain at medium speed and see if chain oil has scattered off, as shown in the figure. The oil flow adjusting screw must be pressed in slightly in order to turn.
-
Page 12: Maintenance
• Make sure that the engine has stopped and is cool be- gap is in the correct range. For a replacement plug, use the fore performing any service to the machine. Contact with correct type specified by ZENOAH. moving cutting head or hot muffler may result in a per- sonal injury. - Page 13 PSZ2600 9. Maintenance SPARK ARRESTER OILING PORT • The muffler is equipped with a spark arrester to prevent red Dismount the guide bar and check the oiling port for clogging. hot carbon from flying out of the exhaust outlet. Periodically (MA1) inspect and clean as necessary with a wire brush in the re- pair specialty store.
- Page 14 PSZ2600 9. Maintenance SPROCKET After every cutter has been set, check the depth gauge and file Check for extensive wear, and replace it when the teeth are it to the proper level as illustrated. (MA7) worn over 0.3 mm. 0.3 mm (1) Sprocket SAW CHAIN 0.025"...
-
Page 15: Storage
→ clogged with dust → consult with the repair specialty store When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal operat-... - Page 16 PSZ2600 To Dealer: Please complete the following form at time of sale. Product Model: Equipment No.: ZENOAH PSZ2600 Engine No.: Private Date of Purchase: D / M / Y Use: Professional Rental Purchaser: Name: Dealer: Name: Address/Phone: Address/Phone: To Purchaser: When your unit requires any repair, please bring or send it to the dealer with this sheet attached.