Advertisement
I=T
_:_
=
'connect BLACK grounding cable to negative (-) term[-
na! with remaining hex bolt, fiat washer, lock washer
SEAT
.
and hex nut. Tighten securely.
"
.
•Close battery box door°
SEAT PAN
Open battery box door for:
..
°
Inspection for secure connections (to tighten hard-
SHOULDER
'::'i;:i
ware),
, :
BOL.T
.. • , lnspectibn for corrosion.
_':':'
PROTECTIVEI//I",\
.....
:: WASHER
. ' :.
,_';i
.:CAPS _//])]
....
'
'
'
,'
;
,'::-
'..
":
.
WASHER
--- _.---:--_ - _--.---
":,,
:,_:i:
:
CHECK:TIRE
PRESSURE,
"
'
"
,
HSX
_h;iiiies o1_ your tracioi:----' -": "
were _b_erinilated at the factory for
;':: _!.
: !!!,::,.:__:_
.::
..:. ;BOLT" _ 5 $_il_lStfig'PbrPOses. Cbrr_cttire press'ure ts irnp6rtant for
_..::
......
' '.
:.,. :: best cLttting"Defformance,'.i ._".
,.
,.
i ;;. :':'
__;
....
: : ,,:_iiRe'd(_e;"ii_:a' pres_ure'!'t0 PSi sh0wn':in "PRODUCT
, :_ :-: SPECIFIGATIONS" on page 3 of this manual.
.!.
NEGATIVE
'
i
!
mower housing 'should be properfy
OUSING" in the
::=
PAN
BATTERY
BOX
DOOR
FIG, 3
INSTALL
SEAT(See
.Fig, 4)
Adjust Seat before t!ghtening adjustment bolt,
Remove ca_rdb0ard packing onseat pan.
•Placeseat on seat pa.n and assemble Shoulder bolt,
e
dj's
i ioCt<
h
d
!Ass mblea
u tmentbol,
was er_n flatwasher
Ioo_ely_ Do n0ttighten.
-,"
.. : .
,:
Tighten shoulder bolt securelY.,
';_,- .
Lower Seat into operating position and sit on Seat.
°
Slide seat Untiia comfortable position is reached Which
allows you to press clutch!broke pedal all the way
down=
:,
Get off seat without moving its adjusted position.
°
Raise seat and tighten adjustment bolt securely.
• .
•8
motion and
-
mbwer blade drive i0elts in
_ arid Adj'ustments
,-section of this manual : :Verify that the belts are routed
correctly_
':
•
:
CHECK BRAKE SYSTEM
After .you learn how to Operate your tractor, check to see
that the brake is properly adjusted.
See "TO ADJUST
BRAKE" in the Service and Adjustrnents
section of this
manual°
ASSEMBLE
GAUGE
WHEELS
TO MOWER
DECK (See Fig. 5)
Assemb. I e gauge wheels with tractor on a flat level surface,
_,
Adjust mower to desired cutting height (see .':TOAD-
"
JUST MOWER CUTTING HEIGHT_' in the Operation
section of this manual).
' _ " '= "
,.
-With .mower' in desired height of cut position, gauge
"
Wl_eelsShould be assembled sb they are sUghtly off the
.
gr0iJhd: Install gauge wheel ,in appfopriatehole
with
-":-' s|pulder
bblt, i3i8" washer and 3/8-i6
10cknut and
i'
t!ghtens_.curely:,:
_":_.:...
? ,;.:
'_' ....
°
Repeat for opposite side installing gauge wheel in
same adjustment hole.
Advertisement
