Table of Contents
Advertisement
612547-207
OWNERS
MANUAL
MODEL
NOr
315,1041-1
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
SAVE THIS
MANUAL
FOR
FUTURE REFERENCE
el_$17,2gY
t,4_e
3/8 INCH
ELECTRIC DRILL
DOUBLE
INSULATED
VARIABLE
SPEED
ADJUSTABLE
- REVERSIBLE
Warranty
Introduction
Operation
Maintenance
Repair
Parts
Dest ned exclusively
for and sold only by
SEARS, ROEBUCK AND CO, Dept
698/73tA,
Sears Tower. Chicago,
IL 60884
®
Advertisement
Table of Contents
Related Manuals for Craftsman 315.10411
Summary of Contents for Craftsman 315.10411
- Page 1 612547-207 OWNERS MANUAL MODEL 315,1041-1 CAUTION: Read Rules for Safe Operation and Instructions 3/8 INCH Carefully ELECTRIC DRILL DOUBLE INSULATED VARIABLE SPEED ADJUSTABLE - REVERSIBLE Warranty SAVE THIS Introduction MANUAL Operation FUTURE REFERENCE Maintenance ® Repair Parts Dest ned exclusively for and sold only by SEARS, ROEBUCK AND CO, Dept 698/73tA,...
- Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN ELECTRIC DRILL If this Etectdc Drill fat_s to give complete satisfaction w_thtn one year from the date of purchase RETURN tT TO THE NEAREST SEARS SERVtCE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES and Sears will repair It, free of charge, If this electric drill Is used for commercial or rental purposes this warJ:antyapptlas for only 90 days from the date of purchase.
- Page 3 RULES FOR SAFE OPERATION (Continued) 12 DON'T ABUSE CORD, Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oi!, and sharp edges. 13. SECURE WORK+ Use clamps or a vise to hold work, Both hands are needed to operate the tool !4, DON'T OVERREACH.
- Page 4 OPERATION KNOW YOUR DRILL AUXILIARY HANDLE Before attempting to use your drill, familiarize yourself with all operat ng leatures and safety re CHUCK "XX"x4 quirements. See Figure 1. CAP SCREW Make sure power supply is t10o120 veils, 60 Hz, AC only.
- Page 5 OPERATION (Cont.) The following guidelines may be used in determining correct speed !or varioes applications: LOW speed Is ideal when minimum speed and power is required For example: starting holes withe_t center punching, mixing paint, and drltllng in ceramics MEDIUM speed }s suitable for drilling hard metals, plastfcs, and laminates HIGH speed produces best results when maximum power is required For example: drllttng in wood;...
- Page 6 OPERATION (Cont.) DRILLING See Ftgure 4 Depress and release the sWitch trigger to be sure your drill Is in the "Off" posttton before connec ring it to power supply Check the direction of rotation lever for correct setting (forward or reverse} Secure the material to be drtlted in a vlse or with clamps...
- Page 7 OPERATION (Cont.) CHUCK REMOVAL See Figures 5, 6 & 7 PiN OR NAIL The chuck must be removed in order to use some ac- cessories To remove: UNPLUG YOUR DRILL, CHUCK Cfose the chuck Jaws Line up hole in spindle with hole In gear housing and insert s 1t8 Inch diameter nail or pin into...
- Page 8 OPERATION (Cont.) CRAFTSMAN CHUCK HOLDER Form a loop by forcing with round holes through slotted hole or_ opposite Figure Place loop over the cord putl it tight. Figure Mount the chuck key by insetting the geared end through the hole...
- Page 9 MAINTENANCE GENERAL When etectr$c toots are used On fiberglass boats, Only the parts shown on parts list, page eleven, are Intended to be repaired or replaced by the customer_ sports cars, etc., it has been found that they are sub- Ject to accelerated wear and possible premature All other parts represent...
- Page 10 CRAFTSMAN 3/8 INCH ELECTRIC DRILL -- MODEL NUMBER 3!5.10411 NOTE "'A"PAGE 11 19 18...
- Page 11 CRA_ ._IAN INCH ELECTRIC DRILL MODEL NUMBER 315.10411 Always mention the Model Number in all correspondence regarding your The Model Number will be found on a pla_,eattached to the Motor Housm 9. t 3/8 INCH ELECTRIC DRILL or when ofdaring repair parts. PARTS LIST Number Description...
- Page 12 3/8 INCH OWNERS ELECTRIC DRILL MANUAL DOUBLE INSULATED VARIABLE SPEED ADJ USTABLE- REVESl BLE SERVICE Now that you have purchased your Eleatrlc Drfll0 should a need ever exist for repair parts or service, .simply contact any Sears Service Center and most Sears, Roebuck and Co.