Advertisement
Quick Links
Quick Setup Guide - Please read this fi rst. It might be all you need to get going.
The X10 SC12A Supervised Security Console with automatic
dialer calls friends or relatives in the event of a break in, and
plays a message (in your voice). Your friend or neighbor can
listen in to your home through the Console's microphone,
and call the police if there's a problem. Accessories include
battery powered Radio Frequency (RF) Door/Window Sensors,
battery powered RF Motion Detectors, and RF Keyfob Remote
Controls for arming and disarming the system.
Console SC12A
Some of the accessories available are shown below. The models
you purchase may vary from those shown below. See your
owner's manual or visit www.x10.com for more information.
Motion Detector
Keyfob Remote
Door/Window
Sensor
Connecting up
1. Open the center lid on the Console. Attach the power
supply's cord to the connector labeled power supply. Plug
the power supply into any AC outlet. (Use only the included
power supply).
2. Attach the phone cord (supplied) to the connector labeled
phone. Plug the other end into an unused phone jack.
3. Install 4 AA alkaline batteries (not supplied) in the
Console's battery compartment.
3.
Close the battery cover. If you open the cover again after
applying power, TAMPER appears in the display. Enter the
PIN (0000) to remove TAMPER from the display. The display
then shows HOME CONTROL in the top line and the time of
day below it.
Initializing the devices
Initializing Keyfob Remotes
Press and hold the ARM button on the Keyfob remote for 3-4
seconds and then release it. This initializes the remote and
picks a random code that is used when it is registered with the
Console.
Initializing Door/Window Sensors
Pry the two halves of the Door/Window Sensor apart and
install 2 AAA alkaline batteries inside. Observe polarity. Note
some Sensors use two AA batteries - follow the instructions
that came with the Sensors.
Set the switch inside to MAX (left) for doors, or MIN (right)
for windows.
Press and hold the button inside the Door/Window Sensor for
3-4 seconds and then release it. This initializes the Sensor and
picks a random code that is used when it is registered with the
Console. Replace the cover and place the magnet next to the
Sensor (with the arrows aligned).
Initializing Motion Detectors
Remove the cover on the front of the Motion Detector and
install 2 AA alkaline batteries in the battery compartment.
Replace the cover (some types of unit have a tamper switch).
Press and hold the TEST button on the back of the Motion
Detector for 3-4 seconds and then release it. This initializes the
Motion Detector and picks a random code that is used when it
is registered with the Console. Place the unit face down, so that
it won't see any motion during the registering process.
Registering the devices
All features (except Home Control) require access to the
Menu mode. To do this, press either of the Menu Start up or
down buttons. The display then shows ENTER PIN (Personal
Identifi cation Number) in the top line. The default PIN is 0000,
see your owner's manual if you want to change this, but for
now press 0000 on the keypad. This clears the top line and
shows * for each number entered. After pressing a Menu Start
up or down button and entering the PIN, the First Level Menu
(INSTALL) is displayed.
1.
1. To select a menu option,
2.
press the up or down
Menu Start button
repeatedly to step through
the menu items 1 through
9.
2. Once you arrive at the
menu item you desire,
press OK to select it.
3. To leave the First Level
Menu, repeatedly press
the Clear button.
Then refer to your Owner's Manual for more detailed information.
Press either of the Menu up/down buttons. The display then
shows ENTER PIN in the top line. Press 0000 on the keypad.
This clears the top line and shows * for each number entered.
When you see INSTALL on the display, press OK.
If you are registering a Keyfob Remote:
Press any button on the Keyfob remote. The Console
acknowledges that it has been registered by beeping and
displaying RMOT 1 SET.
Repeat this for any other Keyfob Remotes you want to register.
The display increments to RMOT 2 SET, etc., as you register
more remotes.
If you are registering Door/Window Sensors:
Move the magnet away from the Door/Window Sensor. The
Console acknowledges that it has been registered with a chime
and by displaying ZONE 1 SET.
Repeat this for any other Door/Window Sensors you want to
register. The display increments to ZONE 2 SET, etc., as you
register more Door Window Sensors.
If you are registering the Motion Detector:
Press the TEST button on the back of the Motion Detector
(or turn the unit over so that it sees motion). The Console
acknowledges that it has been registered by displaying (for
example) ZONE 3 SET.
Repeat this for any other Motion Detectors you want to
register. The display increments to ZONE 4 SET, etc. as you
register more Motion Detectors.
Press Clear to back out of the menus. You are asked to confi rm,
1. YES, 2 NO. Press 1 to go back to the HOME CONTROL
screen. Press 2 to stay in the INSTALL menu.
Installing the Door/Window Sensors
• Set the DELAY slide switch (inside the Sensor) to MIN (for
windows) to always trigger the alarm instantly, or to MAX
(for doors) to trigger the alarm after a preset entry delay
when the system is armed in the AWAY mode.
• Attach the Door/Window Sensor to the wall using the
mounting screws provided (replace the cover).
1.
• Fit the Door/Window Sensor as high as possible at the top
of the door/window.
3.
• Make sure the arrows on the magnet and the Door/Window
Sensor are facing each other and that they separate cleanly
2.
when the door or window is opened.
• To protect two doors or windows close to each other, use
the Door/Window Sensor with an additional set of magnetic
switch contacts (see owner's manual for details).
Installing the Motion Detectors
• Set the slide switch (on the back) to position 1 for instant
triggering for maximum sensitivity, or position 2 to trigger
only after two movements have been sensed.
• Attach the Motion Detector to a wall at a height of 5 to 6 ft.,
using the mounting bracket and screws provided.
• Point the Motion Detector so that it looks slightly downwards.
90°
5-6ft
30-40ft
Arming the system
Press ARM HOME on the Console to arm ALL Door/Window
Sensors instantly. Motion Detectors will not trip the system when
it is armed in the ARM HOME mode.
Press ARM AWAY on the Console to arm all Door/Window
Sensors and Motion Detectors. This arms the system after a set
delay. The delay will be what you specifi ed as the EXIT DELAY
- one minute default (see owner's manual). If you arm the system
in the AWAY mode you will also have an entry delay when you
enter your home before the alarm trips (from Door/Window
Sensors set to MAX, and from Motion Detectors), to give you
time to disarm it. This delay will be what you specifi ed for your
ENTRY DELAY - 30 second default (see owner's manual for
more details).
Pressing ARM on the Keyfob remote always arms in the AWAY
mode, (instantly). ALL Door/Window Sensors and Motion
Detectors trip instantly when armed from the Keyfob.
Disarming the system
Pressing DISARM on the Keyfob remote disarms the system
instantly. The zone that was violated is shown in the Console's
display. To remove this press Arm and Disarm again.
To disarm from the Console: Enter your 4 digit PIN.
This will be 0000 unless you changed it (see owner's manual).
SC1200-5/13
Advertisement
