Advertisement
Quick Links
Gasket Kit #3421
Installation Instructions
for the
Resolute Acclaim Stove
The Acclaim uses a rope-type gasket to make a seal
between some parts. With use, this gasket can be-
come compressed and begin to lose its effectiveness. It
should then be replaced.
Contents:
4’ of 3/16” gasket (door glass frame)
8’ of 5/16” gasket (back, top, upper fireback)
4’ of 5/16” wire gasket (griddle)
6’ of 1/2” gasket (front door)
1 tube of gasket cement
Tools required: Utility knife, wooden block, rubber mal-
let, 1/4” allen wrench, wire brush, flat-blade screwdriver.
Wait till the fire is out and the stove has cooled com-
pletely before replacing the gasket, and be sure to wear
safety goggles and a dust mask.
The procedure for replacing the gaskets is the same,
regardless of the gasket location.
1. Remove the original gasket by grasping an end and
pulling firmly.
2. Use a wire brush or tip of a screwdriver to clean the
channel of any remaining cement or bits of gasket.
Use a cold chisel on stubborn deposits if necessary.
ST560
Fig. 1 Remove gasket then clean channel with wire brush.
ST559
Remove
gasket
11/30/00 djt
3. Determine the right length of the appropriate-sized
gasket by laying it out in the channel. Allow an extra
1-2” (25-50mm) and mark the spot to be cut.
4. Remove the gasket from the channel, place it on
a wooden cutting surface, and cut it at the marked
spot with a utility knife. Twist the ends slightly to
discourage the gasket from unraveling.
5. Apply the cement in the channel. Before you cut the
tip of the cement tube, knead the tube thoroughly to
help mix back into the cement any water that may
have separated during storage. Practice applying the
cement on a piece of newspaper before you apply it
in the channel.
6. Starting at one end, press the gasket into the chan-
nel. Ensure a good joint where the ends meet before
trimming any excess. Do not overlap the gasket
ends or leave ends with ragged edges.
ST561
Fig. 2 Lay a bead of gasket cement then press gasket in
place.
ST559
7. Press the part firmly against its normal mating
Remove
surface to seat the gasket evenly in its channel.
gasket
Tap it with the rubber mallet (or hammer and block
11/30/00 djt
of wood) to help seat it properly. Never hit cast iron
directly with a metal hammer.
8. Clean any excess gasket cement from around the
channel; residual cement will leave a white cast after
it dries. Extra cement will attack and dull an enam-
elled finish, so remove it right away with a damp
rag. Then, let the cement that holds the new gasket
dry for at least 24 hours. Use a slip of waxed paper
between the gasket and the mating surface to keep
the cement from migrating through the gasket and
sticking it to the mating surface.
9. Test the gasket seal by closing the door or griddle
on a piece of paper. Pull gently on the paper. A good
seal will provide firm resistance. A poor seal will let
the paper move freely.
2008847 8/08 Rev. 7
Advertisement
Summary of Contents for Vermont Castings Gasket Kit #3421
-
Page 1: Installation Instructions
3. Determine the right length of the appropriate-sized gasket by laying it out in the channel. Allow an extra 1-2” (25-50mm) and mark the spot to be cut. 4. Remove the gasket from the channel, place it on a wooden cutting surface, and cut it at the marked spot with a utility knife. - Page 2 Care of the Glass Panels If a poor seal is apparent after you have installed a new gasket, and it cannot be corrected with door or Most carbon deposits will burn off the glass during nor- latch adjustment, it may be necessary to insert shim mal use.