Single package gas-electric heating & cooling units pg 15 seer “m” series (28 pages)
Summary of Contents for Goodman CPG SERIES
Page 1
NSTALLATION NSTRUCTIONS & C OMMERCIAL EATING OOLING - 6 T ACKAGE CPG S ERIES ® This Forced Air Central Unit Design Complies With Requirements Embodied in The American National Standard / National Standard of Canada Shown Below. ANSI Z21.47•CSA-2.3 Central Furnaces RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
Index REPLACEMENT PARTS Replacement Parts ............2 RDERING ARTS Safety Instructions ............2 When reporting shortages or damages, or ordering repair parts, give the complete unit model and serial numbers General Information ............3 as stamped on the unit’s nameplate. Unit Location ..............
WARNING WARNING CARBON MONOXIDE POISONING O NOT CONNECT TO OR USE ANY DEVICE THAT IS NOT DESIGN HAZARD CERTIFIED BY OODMAN FOR USE WITH THIS UNIT ERIOUS PROPERTY DAMAGE PERSONAL INJURY REDUCED UNIT FAILURE TO KEEP THIS COMPARTMENT CLOSED EXCEPT WHEN SERVICING COULD RESULT IN PERFORMANCE AND HAZARDOUS CONDITIONS MAY RESULT CARBON MONOXIDE POISONING OR DEATH.
responsibility for equipment installed in violation of any code NSTALLATIONS or regulation. The mechanical installation of the packaged roof top units consists of making final connections between NOTE: Appliance is shipped from factory for vertical duct the unit and building services; supply and return duct con- application.
Full perimeter roof curbs are available from the factory and • The base should also be located where no runoff of are shipped unassembled. Field assembly, squaring, level- water from higher ground can collect in the unit. ing and mounting on the roof structure are the responsibility OOF TOP NSTALLATIONS of the installing contractor.
Adequate clearance around the unit should be kept for safety, CAUTION service, maintenance, and proper unit operation. A total clear- ance of 75” on the main control panel side of the unit is rec- ommended to facilitate possible fan shaft, coil, electric heat F PROTRUSIONS EXIST DO NO ATTEMPT TO SET UNIT ON CURB and gas furnace removal.
RIGGING DETAILS WARNING O PREVENT PROPERTY DAMAGE, THE UNIT SHOULD REMAIN IN AN UPRIGHT POSITION DURING ALL RIGGING AND MOVING OPERATIONS. O FACILITATE LIFTING AND MOVING WHEN A CRANE IS USED, PLACE THE UNIT IN AN ADEQUATE CABLE SLING. CAUTION F UNITS ARE LIFTED TWO AT A TIME THE FORK HOLES ON THE CONDENSER END OF THE UNIT MUST NOT BE USED...
Page 8
RETURN CONDENSER COIL EVAPORATOR COIL SUPPLY COMPRESSOR Corner & Center of Gravity Locations Shipping Operating Corner Weights ( lbs ) Model Weight Weight (in) (in) (lbs) (lbs) CPG036045* CPG036090* CPG048090* CPG048115* CPG060090* CPG060140* CPG072140* * Weights shown are belt drive with no accessories. CAUTION O PREVENT SEVERE DAMAGE TO THE BOTTOM OF THE UNIT DO NOT...
ELECTRICAL WIRING Electrical Code. If long wires are required, it may be neces- sary to increase the wire size to prevent excessive voltage drop. Wires should be sized for a maximum of 3% voltage WARNING drop. HIGH VOLTAGE! CAUTION ISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT ULTIPLE POWER SOURCES MAY BE PRESENT...
Areas Without Convenience Outlet 2. Locate thermostat or remote sensor in the conditioned space where it will sense average temperature. Do It is recommended that an independant 115V power source not locate the device where it may be directly exposed be brought to the vicinity of the roof top unit for portable lights to supply air, sunlight or other sources of heat.
Page 11
(LP) gas is permitted with the use of the factory authorized 4. Install a drip leg to trap dirt and moisture before it can conversion kit (see the unit Technical Manual for the appro- enter the gas valve. The drip leg must be a minimum priate kit).
1. Vaporization rate, which depends on (a) temperature IPING HECKS of the liquid, and (b) wetted surface area of the container or containers. CAUTION 2. Proper pressure regulation. 3. Pressure drop in lines between regulators, and O PREVENT PROPERTY DAMAGE OR PERSONAL INJURY DUE TO FIRE, THE between second stage regulator and the appliance.
NOTE: The gas connection size at the unit does NOT CIRCULATING AIR AND FILTERS establish the size of the supply line. 3. These units are designed for either natural or propane UCTWORK (LP) gas and are specifically constructed at the factory The supply duct should be provided with an access panel for only one of these fuels.
STARTUP, ADJUSTMENTS, AND CHECKS OOLS EQUIRED Refrigeration gauge and manifold Voltmeter WARNING Clamp-on ammeter Ohmmeter HIGH VOLTAGE! O AVOID PERSONAL INJURY OR DEATH DUE TO Test lead ELECTRICAL SHOCK OND THE FRAME OF THIS UNIT TO (Minimum #16 AWG with insulated alligator clips) THE BUILDING ELECTRICAL GROUND BY USE OF THE Manometer for verifying gas pressure 0 to 20"...
Page 15
System Voltage - That nominal voltage value assigned to a VAPORATOR circuit or system for the purpose of designating its voltage Actual RPM’s must be set and verified with a tachometer or class. strobe light. Refer to Appendices A and B for basic unit fan RPM.
Page 16
VAPORATOR OTATION HECK HREE HASE ODELS If the power to the unit is interrupted during the heating cycle, it may cause the secondary limit to trip. Once the blower com- partment temperature drops below the limit reset tempera- Check that fan rotates clockwise when viewed from the drive ture, the limit will automatically reset.
Page 17
Manifold Pressure Check 4. Relight all other appliances turned off in step 1. Be sure all pilot burners are operating. The gas valve has a tapped opening to facilitate measure- ment of the manifold pressure. A “U” Tube manometer hav- Main Burner Flame Check ing a scale range from 0 to 12 inches of water should be Flames should be stable, soft and blue (dust may cause or-...
4. The belt drive blower contactor closes its contacts L1, 7. Disconnecting the jumper wire between R and Y and L2 and L3 to T1, T2 and T3 to provide power to the between R and G on TB1 terminal block will simulate supply fan motor.
supply pressure tap is provided on the upstream side of the 3. Remove the heat exchanger door on the side of the gas valve. A manifold pressure tap is provided on the gas unit by removing screws. valve. The normal manifold pressure for full input is 3.5" w.c. 4.
External Lockout 9. Integrated ignition control will close its normally open contacts after a delay of approximately 30 seconds. An external lockout occurs if the integrated ignition control This action energizes contactor BC and starts the determines that a measurable combustion cannot be estab- supply fan motor.
Pressure Switch Stuck Open INPUT RATING A pressure switch stuck open can be caused by a faulty pres- It is the responsibility of the contractor to adjust the gas input sure switch, faulty wiring, a disconnected or damaged hose, to the unit. The input rate can be calculated by using the a blocked or restricted flue, or a faulty induced draft blower.
To connect manometer to gas valve: EEM Motor 1. Back outlet pressure test screw (inlet/outlet pressure Adjust the CFM for the unit by changing the position of the boss) out one turn (counterclockwise, not more than low voltage leads on the motor terminal block. Green is for one turn).
Page 23
Disposable return air filters are supplied with this unit. See WARNING the unit Specification Sheet or Technical Manual for the cor- rect size and part number. To remove the filters, remove the filter access panel on return side of the unit. O PREVENT PERSONAL INJURY OR DEATH DUE TO IMPROPER INSTALLATION ADJUSTMENT...
Page 24
b. Disconnect wires from the flame rod and ignition WARNING electrode. c. Disconnect the gas piping at the union. O AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRIC SHOCK, d. The entire burner assembly can now be removed DO NOT REMOVE ANY INTERNAL COMPARTMENT COVERS OR ATTEMPT ANY from the unit.
APPENDIX A BLOWER PERFORMANCE TABLES DIRECT DRIVE CPG036 DOWN SHOT AND HORIZONTAL CPG036 DIRECT DRIVE DOWN SHOT EXTERNAL STATIC STANDARD SPEED TAP PRESSU RE (ESP) AMPS WATTS in w.c. 0.10 1313 1.68 0.20 1247 1.63 0.30 1178 1.59 0.40 1094 1.55 0.50 1002...
APPENDIX A BLOWER PERFORMANCE TABLES DIRECT DRIVE CPG048 DOWN SHOT AND HORIZONTAL CPG048 DIRECT DRIVE DOWN SHOT EXTERNAL STATIC STAN DARD SPEED TAP PRESSURE (ESP) AMPS WATTS in w.c. 0.10 1592 2.54 0.20 1528 2.43 0.30 1464 2.32 0.40 1380 2.21 0.50 1296...
APPENDIX A BLOWER PERFORMANCE TABLES DIRECT DRIVE CPG060 DOWN SHOT CPG060 DIRECT DRIVE DOWN SHOT EXTERNAL STATIC SPEED STANDARD PRESSURE (ESP) AMPS WATTS C FM in w.c. 0.10 1237 1.64 0.20 1191 1.75 0.30 1127 1.80 0.40 1065 1.89 0.50 1.97 0.10 1437...
APPENDIX B ELECTRICAL DATA ELECTRICAL DATA OUTDOOR VOLTAGE COMPRESSOR INDOOR INDOOR FAN MOT OR VOLTAGE LIMITATION FAN MOTOR MODELS MOT OR (NAMEPLATE) APPLICATION MIN. MAX. 208/230-60-1 16.67 1.40 DD STD STATIC DD STD STATIC 208/230-60-3 10.45 73.0 1.40 3 TON BD STD STATIC 460-60-3 5.77...
Page 36
CPG036(48)0451D SINGLE PHASE 240V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP 208-240/1/60 SEE NOTE 5 3 SPEED ALTERNATE SMOKE/FIRE...
Page 37
CPG036(48)0451D SINGLE PHASE 240V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. FACTORY WIRING SUPPLY VOLTAGE COMPONENT LEGEND 208-240/1/60 AUXILIARY LIMIT SWITCH LINE VOLTAGE...
Page 38
CPG036(048)0901D SINGLE PHASE 240V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP 208-240/1/60 SEE NOTE 5 3 SPEED ALTERNATE SMOKE/FIRE...
Page 39
CPG036(048)0901D SINGLE PHASE 240V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND FACTORY WIRING SUPPLY VOLTAGE 208-240/1/60 AUXILIARY LIMIT SWITCH LINE VOLTAGE...
Page 40
CPG0060*1D SINGLE PHASE 240V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWER SUPPLY 240/1/60 SEE NOTE 6 NOTE 3 &...
Page 41
CPG0060*1D SINGLE PHASE 240V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. SUPPLY VOLTAGE FACTORY WIRING COMPONENT LEGEND 240/1/60 LINE VOLTAGE AUXILIARY LIMIT SWITCH...
Page 42
CPG060*3D THREE PHASE 208-230V/60HZ DIRECT HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWER SUPPLY 240/3/60 SEE NOTE 5 YL RD NOTE 3 &...
Page 43
CPG060*3D THREE PHASE 208-230V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. SUPPLY VOLTAGE FACTORY WIRING COMPONENT LEGEND 240/3/60 LINE VOLTAGE AUXILIARY LIMIT SWITCH...
Page 44
CPG036(048)*3D THREE PHASE 208-230V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWERSUPPLY 208-240/3/60 SEE NOTE 5 3 SPEED ALTERNATE SMOKE/FIRE...
Page 45
CPG036(048)*3D THREE PHASE 208-230V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND SUPPLY VOLTAGE FACTORY WIRING 208-240/3/60 AUXILIARY LIMIT SWITCH LINE VOLTAGE...
Page 46
CPG036(048)*3D THREE PHASE 230V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWERSUPPLY 208-240/3/60 SEE NOTE 5 3 SPEED ALTERNATE SMOKE/FIRE...
Page 47
CPG036(048)*3D THREE PHASE 230V/60HZ DIRECT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND SUPPLY VOLTAGE FACTORY WIRING 208-240/3/60 AUXILIARY LIMIT SWITCH LINE VOLTAGE...
Page 48
CPG036(48)0904B(7B)/CPG060*4B(7B)/CPG072*4B(7B) THREE PHASE 460V/575V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWER SUPPLY 460/3/60 575/3/60 SEE NOTE 4 460/575 SMOKE/FIRE...
Page 49
CPG036(48)0904B(7B)/CPG060*4B(7B)/CPG072*4B(7B) THREE PHASE 460V/575V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. SUPPLY VOLTAGE COMPONENT LEGEND 460-575/3/60 AUXILIARY LIMIT SWITCH FACTORY WIRING BLOWER CONTACTOR...
Page 50
CPG036(048)0903B/CPG060*3B/CPG072*3B THREE PHASE 208-230V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWER SUPPLY 208-240/3/60 SEE NOTE 4 SMOKE/FIRE DETECTOR REPLACES JUMPER WIRE...
Page 51
CPG036(048)0903B/CPG060*3B/CPG072*3B THREE PHASE 208-230V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND SUPPLY VOLTAGE FACTORY WIRING AUXILIARY LIMIT SWITCH 208-240/3/60 LINE VOLTAGE...
Page 52
CPG036(048)0454B THREE PHASE 575V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWER SUPPLY 460/3/60 575/3/60 SEE NOTE 4 460/575 SMOKE/FIRE...
Page 53
CPG036(048)0454B THREE PHASE 575V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. SUPPLY VOLTAGE COMPONENT LEGEND 460-575/3/60 AUXILIARY LIMIT SWITCH FACTORY WIRING BLOWER CONTACTOR...
Page 54
CPG036(048)0453B THREE PHASE 240V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP POWER SUPPLY 208-240/3/60 SEE NOTE 4 SMOKE/FIRE DETECTOR REPLACES JUMPER WIRE...
Page 55
CPG036(048)0453B THREE PHASE 240V/60HZ BELT DRIVE HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND SUPPLY VOLTAGE FACTORY WIRING AUXILIARY LIMIT SWITCH 208-240/3/60 LINE VOLTAGE...