Table of Contents
Related Manuals for Sears 390.262451
Summary of Contents for Sears 390.262451
- Page 1 "HYDROoGLASS ''_ ,_E/_/,_,_ ESSU E __: _ __,_ _ _,_,i_i!i_ii_i,ii_ i_i_ _ili_i i! _ ! _i_! _ii ¸I_ il ¸I !i_ _,_ - Installation ® Operation ® Repair Parts ._rence. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PRINTED IN U S A Form NO F642-20g2 (3/2B/9s)
- Page 2 CONTENTS nNTRODUCTtON Please take a few minutes to read our instructions before INTRODUCTION/WARRANTY .......... 2 you install and use your pump_ This will help you obtain SAFETY ................the full benefits from this pump It will also help you avoid any needless service costs that result from causes PREPARATION ..............
- Page 3 Before You Install Your Pump BASIC TOOLS MATERIALS NEEDED Pipe Wrenches Screwdriver Hacksaw Check Valve Adjustable Wrench Teflon Tape Knife NOTICE: Welt must not be more than 20' depth to water. 1. Long runs and many fittings increase friction reduce flow. Locate pump as close to well as possible: use as few elbows and fittings as possible°...
-
Page 4: Installation
Well Pipe Installation NOTICE: Use the installation method below which matches your well type° [_ck vaive CASED WELL INSTALLATION Io Inspect foot valve to be sure it works freely. Inspect strainer to be sure it is clean° 2o Connect foot valve and strainer to the first length of suction pipe and lower pipe into well Add sections of pipe as needed, using Teflon tape on male threads_ Be... -
Page 5: Installation
2. Whenthepumpis setawayfromthepointsof water use,the discharge pipesizeshouldbe increased to reduce pressure losses caused by friction, o Up to 100' run: Same size as pump discharge port. = 100' to 300' run: Increase one pipe size, = 300' to 600' run: Increase two pipe sizes. LAWN SPRINKLING APPLICATION This pump is designed for lawn sprinkling°... -
Page 6: Electrical
Electrical Risk of serious or fatal I_WARNINGI Disconnect power at service panel before electrical shock. connecting pressure switch. Connect motor ground wire before connecting power To convertdual-voltagemotors supply wires. from 230 to 115 Volts: Do not ground to a gas tracerfrom B toA supply line. -
Page 7: Operation
Operation more than 20') and length of horizontal run (10' of PRIMING THE PUMP horizontal suction pipe = 1' of vertical lift due to NOTICE: 'Priming' refers to the pump expelling all air in friction losses in the pipe)° the system and beginning to move water from its source if no water is produced within ! 0 minutes, stop pump, out into the system. - Page 8 Maintenance switch on motor end of shaft; hold motor shaft with Pump and piping need not be disconnected to repair or replace motor or seal (see Figure 18)_ If motor is replaced, wrench on shaft flats and unscrew impeller by turning replace the shaft seal (Key Nov 6, Page 1 I).
-
Page 9: Maintenance
Maintenance (Continued) NOTICE: Be sure you do not scratch seal face° Be CarefulThat Does not Damage Dispose of cardboard washer and recheck seal face to Seal Face Shaft Shoulder be sure it is free of dirt, foreign particles, scratches and grease, Inspect shaft to be sure it is free of nicks... - Page 10 Troubleshooting Chart SYMPTOM CORRECTIVE ACTION POSSIBLE CAUSE(S) Disconnect switch is off Be sure switch is on Motor will not run Fuse is blown Replace fuse 3, Starting switch is defective 3, Replace starting switch 4. Wires at motor are loose, Refer to instructions on wiring Check and tighten all wiring.
- Page 11 SEARS "HYDRO-GLASS "® SPRUNKLER PUMPS MODELS 390.262451, 390.262551 and 390.262651 Toorder parts, call: SearsProductService,1-800-366-7278 390.262451 390,262551 390.262651 115/230V 115/230V 230V Part 60 Cy/1 Ph 60 Cy/1 Ph 60 Cy!1 Ph lq12 HP Description 1 HP 2 HP J218-955C J218-956C J218-957C Motor C69-2 C69-2...
-
Page 12: Repair Parts
"HYDRO-GLASS ''® SPRI Now that you have purchased your Sprinkler Pump, should a need ever exist for repair parts or service, simply contact any Sears Service Center. Be sure to provide all pertinent facts when you call or visit. The Model Number of your Sprinkler Pump will be found on a plate attached to the side of the pump body,...