Craftsman 113.27520 Operating Instructions Manual
Craftsman 113.27520 Operating Instructions Manual

Craftsman 113.27520 Operating Instructions Manual

Bench saw 10" tilting arbor

Advertisement

..... : ,,,,,,,: . ......
i,
,
i
i
J ii
i,ii
,,,
.......
OP_RATUNG INSTRUCTIONS
AND
PARTS LIST FOR
(
W
C
@
r
Model
Number
113.27520
The above Model Number
will be found on a plate attached
to
your sa_, at the back, near the bottom of the base.
Always men-
tion the Model
Number
when communicating
with us regarding
your saw or when ordering
parts,
....
Ordering
Information
tor ...................
Retail
and Mail
Order
Stores
1.
Send all ol:rders for parts listed herein direct to:
....
7% ......
A minimu_
,_?,
source on any
order amou
_:¢ ,_:,_ __. ,,,i/._:_
i!
s to be charged
the actual F___. _ ........
'_
:¢'
Markut_: Selling prices on the parts listed produce
a markalp of
approxtmately
AO.
Filing Instructions
File this parts list immediately behind parts list nttmber 113.22411
in the DIVISION
9 Standard Nomenclature
GREY BINDER Vol, II
Printed
in U
S A
ii
$_AR$,
ROEgUCK
AND CO.

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman 113.27520

  • Page 1 ..: ,,,,,,,: ..J ii i,ii ..OP_RATUNG INSTRUCTIONS PARTS LIST FOR Model Number 113.27520 The above Model Number will be found on a plate attached your sa_, at the back, near the bottom of the base. Always men- tion the Model Number when communicating...
  • Page 2: Assembling/Adjusting

    Shift the two trunnious until the two measure- ments are equal, then retighten the screws. Again Check measurement. INSTALL RIP FENCE--Secure the rack (J, fig. 1) to Your Craftsman shipped complete (without the front skirt of the saw,tabIe, using the three screws motor)
  • Page 3: Motor Specifications

    moving the motor support assembly towards or away from the cradle. Motor should be allowed to rest or hang against the belt to obtain the automatic belt tightening feature--and belt should be snug. If adjustment ,s cor- rect, clamp the motor support in place by tightening the two square head set screws (part S-1267, fig.
  • Page 4: Operating Adjustments

    so that it touches 'the right side of the saw blade--then set indicator at "0". Move fence to left side of blade and ad- ADJUSTING TILT GAGE Using just left-hand indicator in like manner. accurate square, blade ADJUSTING CLAMP LEVER right angles to table top.
  • Page 5: Standarв Operations

    RI:SAW HG Resawing is the cutting of thick boards into thinner ones. It is RIPP_HG a ripping operation, Small boards -- up to 3_/[_-inchmaximum width -_ _ Ripping is the sawing of wood with the grain. It is --can be resawed in one pass;...
  • Page 6 CROSSCUTTING Continued inch wide can be .cut,. Outside blades can be used alone, chippers cannot. covers table in front of blade, A dado insert (part 9-2212, fig. 4) must be used to re- gage should be reversed_ Square crosscutting is done with the miter place the standard table...
  • Page 7: Parts List & View

    : All parts illustrated :in:Fi :[:and listed bers must be ordered or [Mail Orde: :etc.; are :Sta_flar_ items arid im...
  • Page 8 3557 3557 FIGURE 5 PARTS LIST Prepaid [7_:i Prepaid "':7-:. Prel?aid, Prtee : Pric_ • Price Part NAME PARt Each Part No_ NAbIE PART ::Each Part Each DEPTH DIAL ASSEMBLY 6380 Arbor Housing ..... L..[: :7.50 %Vasher ......Lift 5-1211 Spring X_ashe¢...

Table of Contents